FreeBSD Manual Pages
RECOVERDISK(1) General Commands Manual RECOVERDISK(1) NAME recoverdisk -- recover data from hard disk or optical media SYNOPSIS recoverdisk [-b bigsize] [-r readlist] [-s interval] [-u pattern] [-v] [-w writelist] source [destination] DESCRIPTION The recoverdisk utility reads data from the source file until all blocks could be successfully read. If destination was specified all data is being written to that file. It starts reading in multiples of the sector size. Whenever a block fails, it is put to the end of the working queue and will be read again, possibly with a smaller read size. By default it uses block sizes of roughly 1 MB, 32kB, and the native sector size (usually 512 bytes). These figures are adjusted slightly, for devices whose sectorsize is not a power of 2, e.g., audio CDs with a sector size of 2352 bytes. The options are as follows: -b bigsize The size of reads attempted first. The middle pass is roughly the logarithmic average of the bigsize and the sectorsize. -r readlist Read the list of blocks and block sizes to read from the speci- fied file. -s interval How often we should update the writelist file while things go OK. The default is 60 and the unit is "progress messages" so if things go well, this is the same as once per minute. -u pattern By default blocks which encounter read errors will be filled with the pattern `_UNREAD_' in the output file. This option can be used to specify another pattern. Nothing gets written if the string is empty. -v Enables nicer status report using ANSI escapes and UTF-8. -w writelist Write the list of remaining blocks to read to the specified file if recoverdisk is aborted via SIGINT. The -r and -w options can be specified together. Especially, they can point to the same file, which will be updated on abort. OUTPUT The recoverdisk utility prints several columns, detailing the progress start Starting offset of the current block. size Read size of the current block. len Length of the current block. state Is increased for every failed read. done Number of bytes already read. remaining Number of bytes remaining. % done Percent complete. EXAMPLES # recover data from failing hard drive ada3 recoverdisk /dev/ada3 /data/disk.img # clone a hard disk recoverdisk /dev/ada3 /dev/ada4 # read an ISO image from a CD-ROM recoverdisk /dev/cd0 /data/cd.iso # continue reading from a broken CD and update the existing worklist recoverdisk -r worklist -w worklist /dev/cd0 /data/cd.iso # recover a single file from the unreadable media recoverdisk /cdrom/file.avi file.avi # If the disk hangs the system on read-errors try: recoverdisk -b 0 /dev/ada3 /somewhere SEE ALSO dd(1), ada(4), cam(4), cd(4), da(4) HISTORY The recoverdisk utility first appeared in FreeBSD 7.0. AUTHORS The original implementation was done by Poul-Henning Kamp <phk@FreeBSD.org> with minor improvements from Ulrich Sporlein <uqs@FreeBSD.org>. This manual page was written by Ulrich Sporlein. BUGS Reading from media where the sectorsize is not a power of 2 will make all 1 MB reads fail. This is due to the DMA reads being split up into blocks of at most 128kB. These reads then fail if the sectorsize is not a divisor of 128kB. When reading a full raw audio CD, this leads to roughly 700 error messages flying by. This is harmless and can be avoided by setting -b to no more than 128kB. recoverdisk needs to know about read errors as fast as possible, i.e., retries by lower layers will usually slow down the operation. When us- ing cam(4) attached drives, you may want to set kern.cam.XX.retry_count to zero, e.g.: # sysctl kern.cam.ada.retry_count=0 # sysctl kern.cam.cd.retry_count=0 # sysctl kern.cam.da.retry_count=0 FreeBSD 13.2 April 3, 2020 RECOVERDISK(1)
NAME | SYNOPSIS | DESCRIPTION | OUTPUT | EXAMPLES | SEE ALSO | HISTORY | AUTHORS | BUGS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=recoverdisk&sektion=1&manpath=FreeBSD+14.0-RELEASE+and+Ports>