FreeBSD Manual Pages
AUE(4) Kernel Interfaces Manual AUE(4) NAME aue -- ADMtek AN986 Pegasus USB Fast Ethernet driver SYNOPSIS To compile this driver into the kernel, place the following lines in your kernel configuration file: device uhci device ohci device usb device miibus device uether device aue Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_aue_load="YES" DESCRIPTION The aue driver provides support for USB Fast Ethernet adapters based on the ADMtek AN986 Pegasus chipset. The LinkSys USB10T adapters that contain the AN986 Pegasus chipset will operate at 100Base-TX and full-duplex. The Pegasus contains a 10/100 Ethernet MAC with MII interface and is designed to work with both Ethernet and HomePNA transceivers. Although designed to interface with 100Mbps peripherals, the existing USB stan- dard specifies a maximum transfer speed of 12Mbps. Users should there- fore not expect to actually achieve 100Mbps speeds with these devices. The Pegasus supports a 64-bit multicast hash table, single perfect fil- ter entry for the station address and promiscuous mode. Packets are received and transmitted over separate USB bulk transfer endpoints. The aue driver supports the following media types: autoselect Enable autoselection of the media type and op- tions. The user can manually override the autos- elected mode by adding media options to the /etc/rc.conf file. 10baseT/UTP Set 10Mbps operation. The mediaopt option can also be used to enable full-duplex operation. Not specifying full duplex implies half-duplex mode. 100baseTX Set 100Mbps (Fast Ethernet) operation. The mediaopt option can also be used to enable full-duplex operation. Not specifying full duplex implies half-duplex mode. The aue driver supports the following media options: full-duplex Force full duplex operation. The interface will operate in half duplex mode if this media option is not specified. For more information on configuring this device, see ifconfig(8). HARDWARE The aue driver supports the following USB Fast Ethernet adapters based on the ADMtek AN986 Pegasus chipset: • Abocom UFE1000, DSB650TX_NA • Accton USB320-EC, SpeedStream • ADMtek AN986, AN8511 • Billionton USB100, USB100LP, USB100EL, USBE100 • Corega Ether FEther USB-T, FEther USB-TX, FEther USB-TXS • D-Link DSB-650, DSB-650TX, DSB-650TX-PNA • Elecom LD-USBL/TX • Elsa Microlink USB2Ethernet • HP hn210e • I-O Data USB ETTX • Kingston KNU101TX • LinkSys USB10T adapters that contain the AN986 Pegasus chipset, USB10TA, USB10TX, USB100TX, USB100H1 • MELCO LUA-TX, LUA2-TX • Netgear FA101 • Planex UE-200TX • Sandberg USB to Network Link (model number 133-06) • Siemens Speedstream • SmartBridges smartNIC • SMC 2202USB • SOHOware NUB100 DIAGNOSTICS aue%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. aue%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8) ADMtek AN986 data sheet, http://www.admtek.com.tw. HISTORY The aue device driver first appeared in FreeBSD 4.0. AUTHORS The aue driver was written by Bill Paul <wpaul@ee.columbia.edu>. FreeBSD 15.0 May 26, 2025 AUE(4)
NAME | SYNOPSIS | DESCRIPTION | HARDWARE | DIAGNOSTICS | SEE ALSO | HISTORY | AUTHORS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=aue&sektion=4&manpath=FreeBSD+15.0-RELEASE+and+Ports>