home | help
ATA(4)			     Kernel Interfaces Manual			  ATA(4)

NAME
     ata, acd, ad, afd, ast -- generic ATA/ATAPI disk controller driver

SYNOPSIS
     For ISA based ATA/ATAPI support:
     device isa
     device ata0 at isa? port IO_WD1 irq 14
     device ata1 at isa? port IO_WD2 irq 15

     For PCI based ATA/ATAPI support:
     device pci
     device ata

     To support ATA compliant disk drives:
     device atadisk

     To support ATAPI CD-ROM, CDR, CDRW, DVD-ROM and DVD-RAM drives:
     device atapicd

     To support ATAPI floppy drives, such as the ZIP and LS120:
     device atapifd

     To support ATAPI tape drives:
     device atapist

     The following tunables are setable from the loader:

     hw.ata.ata_dma
     set to 1 for DMA access, 0 for PIO (default is DMA).

     hw.ata.atapi_dma
     set to 1 for DMA access, 0 for PIO (default is PIO).

     hw.ata.wc
     set to 1 to enable Write Caching, 0 to disable (default is disabled).
     (WARNING: might cause data loss on power failures.)

     hw.ata.tags
     set to 1 to enable Tagged Queuing support, 0 to disable (default is
     disabled).  (Only IBM DPTA, DTLA, ICxxxxxxAT, ICxxxxxxAV drives support
     that.)

DESCRIPTION
     This  driver  provides  access to disk drives, ATAPI CD-ROM and DVD drives,
     ZIP drives and tape streamers connected to controllers according to the ATA
     and ATAPI standards.  These devices are also commonly known as IDE or  EIDE
     devices.

     The currently supported controllers with their maximum speed include:

     Acerlabs Aladdin			    Ultra  DMA	100  (UDMA5), 100 MB/sec
					    (depending on model, max  stated  at
					    boot)
     AMD 756				    Ultra DMA 66 (UDMA4), 66 MB/sec
     AMD 766				    Ultra DMA 100 (UDMA5), 100 MB/sec
     CMD 646				    DMA 2 (WDMA2), 16 MB/sec
     CMD 648				    Ultra DMA 66 (UDMA4), 66 MB/sec
     CMD 649				    Ultra DMA 100 (UDMA5), 100 MB/sec
     Cypress 82C693			    DMA 2 (WDMA2), 16 MB/sec
     Cyrix 5530 			    Ultra DMA 33 (UDMA2), 33 MB/sec
     HighPoint HPT366			    Ultra DMA 66 (UDMA4), 66 MB/sec
     HighPoint HPT370			    Ultra DMA 100 (UDMA5), 100 MB/sec
     HighPoint HPT372			    Ultra DMA 133 (UDMA6), 133 MB/sec
     HighPoint HPT374			    Ultra DMA 133 (UDMA6), 133 MB/sec
     Intel PIIX 			    DMA 2 (WDMA2), 16 MB/sec
     Intel PIIX3			    DMA 2 (WDMA2), 16 MB/sec
     Intel PIIX4			    Ultra DMA 33 (UDMA2), 33 MB/sec
     Intel ICH0 			    Ultra DMA 33 (UDMA2), 33 MB/sec
     Intel ICH				    Ultra DMA 66 (UDMA4), 66 MB/sec
     Intel ICH2 			    Ultra DMA 100 (UDMA5), 100 MB/sec
     Intel ICH3 			    Ultra DMA 100 (UDMA5), 100 MB/sec
     Intel ICH4 			    Ultra DMA 100 (UDMA5), 100 MB/sec
     Promise Ultra/Fasttrak-33		    Ultra DMA 33 (UDMA2), 33 MB/sec
     Promise Ultra/Fasttrak-66		    Ultra DMA 66 (UDMA4), 66 MB/sec
     Promise Ultra/Fasttrak-100 	    Ultra DMA 100 (UDMA5), 100 MB/sec
     Promise Ultra/Fasttrak-100 TX2/TX4     Ultra DMA 100 (UDMA5), 100 MB/sec
     Promise Ultra/Fasttrak-133 TX2/TX2000  Ultra DMA 133 (UDMA6), 133 MB/sec
     ServerWorks ROSB4			    Ultra DMA 33 (UDMA2), 33 MB/sec
     ServerWorks CSB5			    Ultra  DMA	100  (UDMA5), 100 MB/sec
					    (depending on model, max  stated  at
					    boot)
     Sil 0680				    Ultra  DMA	133  (UDMA6), 133 MB/sec
					    (depending on model, max  stated  at
					    boot)
     SiS 5591				    Ultra  DMA	100  (UDMA5), 100 MB/sec
					    (depending on model, max  stated  at
					    boot)
     VIA 82C586 			    Ultra DMA 33 (UDMA2), 33 MB/sec
     VIA 82C596 			    Ultra DMA 66 (UDMA4), 66 MB/sec (de-
					    pending  on  model,  max  stated  at
					    boot)
     VIA 82C686a			    Ultra DMA 66 (UDMA4), 66 MB/sec
     VIA 82C686b			    Ultra DMA 100 (UDMA5), 100 MB/sec
     VIA 8233/8235			    Ultra DMA 133  (UDMA6),  133  MB/sec
					    (depending	on  model, max stated at
					    boot)

     All unknown chipsets are supported at the maximum speed of 16 MB/sec.

     The ata driver also allows for changes to the transfer mode of the  devices
     at a later time when the system is up and running, see atacontrol(8).

     The  driver  attempts  to set the maximum performance transfer mode on your
     disk drives by selecting the highest possible DMA	mode.  However	the  ata
     driver  sometimes issue the message "DMA limited to UDMA33, non-ATA66 cable
     or device", if the cable is ATA66 (or above) compliant, it is  because  the
     other  device  on	this  channel states it can only accept upto UDMA2/ATA33
     signals.  ATAPI devices are left in PIO mode because DMA problems are  com-
     mon  despite the device specifications.  You can always try to set DMA mode
     on an ATAPI device using atacontrol(8), but be  aware  that  your	hardware
     might not support it and can hang the system.

FILES
     /dev/ad*		      ATA disk device nodes
     /dev/acd*		      ATAPI CD-ROM device nodes
     /dev/afd*		      ATAPI floppy drive device nodes
     /dev/ast*		      ATAPI tape drive device nodes
     /sys/i386/conf/GENERIC   sample  generic  kernel  config file for ata based
			      systems

NOTES
     Static numbering (enabled with the ATA_STATIC_ID kernel option) reserves  a
     number  for  each possibly connected disk, even when not present.	This may
     result in odd situations where, for example, ad0 and ad2 exist in	the  ab-
     sence  of	ad1.   The advantage is that the addition of the formerly absent
     drive does not cause the numbers of the other drives to change.

     The ata driver does not support MFM/RLL/ESDI (ST-506) style disks.

     Remember that in order to use UDMA4 (and above) mode you have to use a spe-
     cial 80 conductor cable, and the driver tries to determine if you have such
     a cable attached before setting UDMA4 mode.

     The use of UDMA4(66MHz) and higher together with non-UDMA4 devices  on  the
     same  ATA	channel is not recommended, unless they are run at the non-UDMA4
     device's lower speed.  The driver has been designed to handle that kind  of
     setup but lots of older devices do not like this.

SEE ALSO
     atacontrol(8), burncd(8)

HISTORY
     The ata driver first appeared in FreeBSD 4.0.

AUTHORS
     The ata driver was written by Soren Schmidt <sos@FreeBSD.org>.

     This   manual   page   was   written  by  Jeroen  Ruigrok	van  der  Werven
     <asmodai@FreeBSD.org> and Soren Schmidt <sos@FreeBSD.org>.

FreeBSD 4.7			January 27, 2000			  ATA(4)

home | help