MOUSED(8) System Manager's Manual MOUSED(8) NAME moused -- pass mouse data to the console driver SYNOPSIS moused [-DPRacdfs] [-I file] [-F rate] [-r resolution] [-S baudrate] [-a X[,Y]] [-C threshold] [-m N=M] [-w N] [-z target] [-t mousetype] [-3 [-E timeout]] -p port moused [-Pd] -p port -i info DESCRIPTION The mouse daemon moused and the console driver work together to support mouse operation in the text console and user programs. They virtualize the mouse and provide user programs with mouse data in the standard format (see sysmouse(4)). The mouse daemon listens to the specified port for mouse data, interprets and then passes it via ioctls to the console driver. The mouse daemon re- ports translation movement, button press/release events and movement of the roller or the wheel if available. The roller/wheel movement is reported as ``Z'' axis movement. The console driver will display the mouse pointer on the screen and provide cut and paste functions if the mouse pointer is enabled in the virtual con- sole via vidcontrol(1). If sysmouse(4) is opened by the user program, the console driver also passes the mouse data to the device so that the user program will see it. If the mouse daemon receives the signal SIGHUP, it will reopen the mouse port and reinitializes itself. Useful if the mouse is attached/detached while the system is suspended. The following options are available: -3 Emulate the third (middle) button for 2-button mice. It is emu- lated by pressing the left and right physical buttons simultane- ously. -C threshold Set double click speed as the maximum interval in msec between but- ton clicks. Without this option, the default value of 500 msec will be assumed. This option will have effect only on the cut and paste operations in the text mode console. The user program which is reading mouse data via sysmouse(4) will not be affected. -D Lower DTR on the serial port. This option is valid only if mousesystems is selected as the protocol type. The DTR line may need to be dropped for a 3-button mouse to operate in the mousesystems mode. -E timeout When the third button emulation is enabled (see above), the moused daemon waits timeout msec at most before deciding whether two but- tons are being pressed simultaneously. The default timeout is 100 msec. -F rate Set the report rate (reports/sec) of the device if supported. -I file Write the process id of the moused daemon in the specified file. Without this option, the process id will be stored in /var/run/moused.pid. -P Do not start the Plug and Play COM device enumeration procedure when identifying the serial mouse. If this option is given to- gether with the -i option, the moused command will not be able to print useful information for the serial mouse. -R Lower RTS on the serial port. This option is valid only if mousesystems is selected as the protocol type by the -t option be- low. It is often used with the -D option above. Both RTS and DTR lines may need to be dropped for a 3-button mouse to operate in the mousesystems mode. -S baudrate Select the baudrate for the serial port (1200 to 9600). Not all serial mice support this option. -a X[,Y] Accelerate or decelerate the mouse input. This is a linear accel- eration only. Values less than 1.0 slow down movement, values greater than 1.0 speed it up. Specifying only one value sets the acceleration for both axes. -c Some mice report middle button down events as if the left and right buttons are being pressed. This option handles this. -d Enable debugging messages. -f Do not become a daemon and instead run as a foreground process. Useful for testing and debugging. -i info Print specified information and quit. Available pieces of informa- tion are: port Port (device file) name, i.e. /dev/cuaa0, /dev/mse0 and /dev/psm0. if Interface type: serial, bus, inport or ps/2. type Protocol type. It is one of the types listed under the -t option below or sysmouse if the driver supports the sysmouse data format standard. model Mouse model. The moused command may not always be able to identify the model. all All of the above items. Print port, interface, type and model in this order in one line. If the moused command cannot determine the requested information, it prints ``unknown'' or ``generic''. -m N=M Assign the physical button M to the logical button N. You may specify as many instances of this option as you like. More than one physical button may be assigned to a logical button at the same time. In this case the logical button will be down, if either of the assigned physical buttons is held down. Do not put space around `='. -p port Use port to communicate with the mouse. -r resolution Set the resolution of the device; in Dots Per Inch, or low, medium-low, medium-high or high. This option may not be supported by all the device. -s Select a baudrate of 9600 for the serial line. Not all serial mice support this option. -t type Specify the protocol type of the mouse attached to the port. You may explicitly specify a type listed below, or use auto to let the moused command to automatically select an appropriate protocol for the given mouse. If you entirely ommit this options in the command line, -t auto is assumed. Under normal circumstances, you need to use this option only if the moused command is not able to detect the protocol automatically (see the "Configuring Mouse Daemon"). Note that if a protocol type is specified with this option, the -P option above is implied and Plug and Play COM device enumeration procedure will be disabled. Also note that if your mouse is attached to the PS/2 mouse port, you should always choose auto or ps/2, regardless of the brand and model of the mouse. Likewise, if your mouse is attached to the bus mouse port, choose auto or busmouse. Serial mouse protocols will not work with these mice. For the USB mouse, the protocol must be auto. No other protocol will work with the USB mouse. Valid types for this option are listed below. For the serial mouse: microsoft Microsoft serial mouse protocol. Most 2-button serial mice use this protocol. intellimouse Microsoft IntelliMouse protocol. Genius NetMouse, ASCII Mie Mouse, Logitech MouseMan+ and First- Mouse+ use this protocol too. Other mice with a roller/wheel may be compatible with this protocol. mousesystems MouseSystems 5-byte protocol. 3-button mice may use this protocol. mmseries MM Series mouse protocol. logitech Logitech mouse protocol. Note that this is for old Logitech models. mouseman or intellimouse should be specified for newer models. mouseman Logitech MouseMan and TrackMan protocol. Some 3-button mice may be compatible with this proto- col. Note that MouseMan+ and FirstMouse+ use intellimouse protocol rather than this one. glidepoint ALPS GlidePoint protocol. thinkingmouse Kensington ThinkingMouse protocol. mmhitab Hitachi tablet protocol. x10mouseremote X10 MouseRemote. kidspad Genius Kidspad and Easypad protocol. versapad Interlink VersaPad protocol. For the bus and InPort mouse: busmouse This is the only protocol type available for the bus and InPort mouse and should be specified for any bus mice and InPort mice, regardless of the brand. For the PS/2 mouse: ps/2 This is the only protocol type available for the PS/2 mouse and should be specified for any PS/2 mice, regardless of the brand. For the USB mouse, auto is the only protocol type available for the USB mouse and should be specified for any USB mice, regardless of the brand. -w N Make the physical button N act as the wheel mode button. While this button is pressed, X and Y axis movement is reported to be zero and the Y axis movement is mapped to Z axis. You may further map the Z axis movement to virtual buttons by the -z option below. -z target Map Z axis (roller/wheel) movement to another axis or to virtual buttons. Valid target maybe: x y X or Y axis movement will be reported when the Z axis movement is detected. N Report down events for the virtual buttons N and N+1 respec- tively when negative and positive Z axis movement is detected. There do not need to be physical buttons N and N+1. Note that mapping to logical buttons is carried out after mapping from the Z axis movement to the virtual buttons is done. N1 N2 Report down events for the virtual buttons N1 and N2 respec- tively when negative and positive Z axis movement is detected. N1 N2 N3 N4 This is useful for the mouse with two wheels of which the sec- ond wheel is used to generate horizontal scroll action, and for the mouse which has a knob or a stick which can detect the horizontal force applied by the user. The motion of the second wheel will be mapped to the buttons N3, for the negative direction, and N4, for the positive di- rection. If the buttons N3 and N4 actually exist in this mouse, their actions will not be detected. Note that horizontal movement or second roller/wheel movement may not always be detected, because there appears to be no ac- cepted standard as to how it is encoded. Note also that some mice think left is the negative horizontal direction, others may think otherwise. Moreover, there are some mice whose two wheels are both mounted vertically, and the direction of the second vertical wheel does not match the first one's. Configuring Mouse Daemon The first thing you need to know is the interface type of the mouse you are going to use. It can be determined by looking at the connector of the mouse. The serial mouse has a D-Sub female 9- or 25-pin connector. The bus and InPort mice have either a D-Sub male 9-pin connector or a round DIN 9-pin connector. The PS/2 mouse is equipped with a small, round DIN 6-pin connector. Some mice come with adapters with which the connector can be converted to another. If you are to use such an adapter, remember the con- nector at the very end of the mouse/adapter pair is what matters. The USB mouse has a flat rectangular connector. The next thing to decide is a port to use for the given interface. For the bus, InPort and PS/2 mice, there is little choice: the bus and InPort mice always use /dev/mse0, and the PS/2 mouse is always at /dev/psm0. There may be more than one serial port to which the serial mouse can be attached. Many people often assign the first, built-in serial port /dev/cuaa0 to the mouse. You can attach multiple USB mice to your system or to your USB hub. They are accessible as /dev/ums0, /dev/ums1, and so on. ~ You may want to create a symbolic link /dev/mouse pointing to the real port to which the mouse is connected, so that you can easily distinguish which is your ``mouse'' port later. The next step is to guess the appropriate protocol type for the mouse. The moused command may be able to automatically determine the protocol type. Run the moused command with the -i option and see what it says. If the command can identify the protocol type, no further investigation is neces- sary on your part. You may start the daemon without explicitly specifying a protocol type (see "EXAMPLES"). The command may print sysmouse if the mouse driver supports this protocol type. Note that the type and model printed by the -i option do not necessarily match the product name of the pointing device in question, but they may give the name of the device with which it is compatible. If the -i option yields nothing, you need to specify a protocol type to the moused command by the -t option. You have to make a guess and try. There is rule of thumb: 1. The bus and InPort mice always use busmouse protocol regardless of the brand of the mouse. 2. The ps/2 protocol should always be specified for the PS/2 mouse re- gardless of the brand of the mouse. 3. You must specify the auto protocol for the USB mouse. 4. Most 2-button serial mice support the microsoft protocol. 5. 3-button serial mice may work with the mousesystems protocol. If it does not, it may work with the microsoft protocol although the third (middle) button will not function. 3-button serial mice may also work with the mouseman protocol under which the third button may function as expected. 6. 3-button serial mice may have a small switch to choose between ``MS'' and ``PC'', or ``2'' and ``3''. ``MS'' or ``2'' usually mean the microsoft protocol. ``PC'' or ``3'' will choose the mousesystems pro- tocol. 7. If the mouse has a roller or a wheel, it may be compatible with the intellimouse protocol. To test if the selected protocol type is correct for the given mouse, en- able the mouse pointer in the current virtual console, vidcontrol -m on start the mouse daemon in the foreground mode, moused -f -p _selected_port_ -t _selected_protocol_ and see if the mouse pointer travels correctly according to the mouse move- ment. Then try cut & paste features by clicking the left, right and middle buttons. Type ^C to stop the command. Multiple Mice As many instances of the mouse daemon as the number of mice attached to the system may be run simultaneously; one instance for each mouse. This is useful if the user wants to use the built-in PS/2 pointing device of a lap- top computer while on the road, but wants to use a serial mouse when s/he attaches the system to the docking station in the office. Run two mouse daemons and tell the application program (such as the X Window System) to use sysmouse, then the application program will always see mouse data from either mice. When the serial mouse is not attached, the corresponding mouse daemon will not detect any movement or button state change and the application program will only see mouse data coming from the daemon for the PS/2 mouse. In contrast when both mice are attached and both of them are moved at the same time in this configuration, the mouse pointer will travel across the screen just as if movement of the mice is combined all together. FILES /dev/consolectl device to control the console /dev/mse%d bus and InPort mouse driver /dev/psm%d PS/2 mouse driver /dev/sysmouse virtualized mouse driver /dev/ttyv%d virtual consoles /dev/ums%d USB mouse driver /var/run/moused.pid process id of the currently running moused daemon /var/run/MouseRemote UNIX-domain stream socket for X10 MouseRemote events EXAMPLES moused -p /dev/cuaa0 -i type Let the moused command determine the protocol type of the mouse at the ser- ial port /dev/cuaa0. If successful, the command will print the type, oth- erwise it will say ``unknown''. moused -p /dev/cuaa0 vidcontrol -m on If the moused command is able to identify the protocol type of the mouse at the specified port automatically, you can start the daemon without the -t option and enable the mouse pointer in the text console as above. moused -p /dev/mouse -t microsoft vidcontrol -m on Start the mouse daemon on the serial port /dev/mouse. The protocol type microsoft is explicitly specified by the -t option. moused -p /dev/mouse -m 1=3 -m 3=1 Assign the physical button 3 (right button) to the logical button 1 (logi- cal left) and the physical button 1 (left) to the logical button 3 (logical right). This will effectively swap the left and right buttons. moused -p /dev/mouse -t intellimouse -z 4 Report negative Z axis (roller) movement as the button 4 pressed and posi- tive Z axis movement as the button 5 pressed. CAVEATS The moused command does not currently work with the alternative console driver pcvt(4). Many pad devices behave as if the first (left) button were pressed if the user `taps' the surface of the pad. In contrast, some ALPS GlidePoint and Interlink VersaPad models treat the tapping action as fourth button events. Use the option ``-m 1=4'' for these models to obtain the same effect as the other pad devices. Cut and paste functions in the virtual console assume that there are three buttons on the mouse. The logical button 1 (logical left) selects a region of text in the console and copies it to the cut buffer. The logical button 3 (logical right) extends the selected region. The logical button 2 (logi- cal middle) pastes the selected text at the text cursor position. If the mouse has only two buttons, the middle, `paste' button is not available. To obtain the paste function, use the -3 option to emulate the middle but- ton, or use the -m option to assign the physical right button to the logi- cal middle button: ``-m 2=3''. SEE ALSO kill(1), vidcontrol(1), keyboard(4), mse(4), pcvt(4), psm(4), screen(4), sysmouse(4), ums(4) STANDARDS The moused command partially supports "Plug and Play External COM Device Specification" in order to support PnP serial mice. However, due to vari- ous degrees of conformance to the specification by existing serial mice, it does not strictly follow the version 1.0 of the standard. Even with this less strict approach, it may not always determine an appropriate protocol type for the given serial mouse. AUTHORS The moused command was written by Michael Smith <msmith@FreeBSD.org>. This manual page was written by Mike Pritchard <mpp@FreeBSD.org>. The command and manual page have since been updated by Kazutaka Yokota <yokota@FreeBSD.org>. HISTORY The moused command first appeared in FreeBSD 2.2. FreeBSD 4.7 April 1, 2000 MOUSED(8)
NAME | SYNOPSIS | DESCRIPTION | FILES | EXAMPLES | CAVEATS | SEE ALSO | STANDARDS | AUTHORS | HISTORY
Want to link to this manual page? Use this URL:
<https://man.FreeBSD.org/cgi/man.cgi?query=moused&sektion=8&manpath=FreeBSD+4.7-RELEASE>