home | help
SF(4)			     Kernel Interfaces Manual			   SF(4)

NAME
     sf -- Adaptec AIC-6915 "Starfire" PCI fast ethernet adapter driver

SYNOPSIS
     device miibus
     device sf

DESCRIPTION
     The  sf driver provides support for Adaptec Duralink fast ethernet adapters
     based on the Adaptec AIC-6915 "Starfire" chipset.	This includes  the  fol-
     lowing:

	   *   ANA-62011 64-bit single port 10/100baseTX adapter
	   *   ANA-62022 64-bit dual port 10/100baseTX adapter
	   *   ANA-62044 64-bit quad port 10/100baseTX adapter
	   *   ANA-69011 32-bit single port 10/100baseTX adapter
	   *   ANA-62020 64-bit single port 100baseFX adapter

     The AIC-6915 is a bus master controller with an MII interface.  It supports
     high and low priority transmit and receive queues, TCP/IP checksum offload,
     multiple  DMA descriptor formats and both polling and producer/consumer DMA
     models.  The AIC-6915 receive filtering options include a 16 entry  perfect
     filter,  a 512-bit hash table for multicast addresses, a 512-bit hash table
     for priority address matching and VLAN filtering.	An external  MII-compli-
     ant transceiver is required for media interfacing.

     Multiport	adapters consist of several AIC-6915 controllers connected via a
     PCI to PCI bridge.  Each controller is treated as a separate  interface  by
     the sf driver.

     The sf driver supports the following media types:

     autoselect 	   Enable  autoselection  of the media type and options.
			   The user can manually override the autoselected  mode
			   by adding media options to the /etc/rc.conf file.

     10baseT/UTP	   Set	10Mbps	operation.  The mediaopt option can also
			   be used to select either full-duplex  or  half-duplex
			   modes.

     100baseTX		   Set	100Mbps (fast ethernet) operation.  The mediaopt
			   option can also be used to select either  full-duplex
			   or half-duplex modes.

     The sf driver supports the following media options:

     full-duplex	   Force full duplex operation

     half-duplex	   Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

DIAGNOSTICS
     sf%d: couldn't map memory	A fatal initialization error has occurred.  This
     may  happen if the PCI BIOS not configured the device, which may be because
     the BIOS has been configured for a "Plug and Play" operating  system.   The
     "Plug  and  Play  OS" setting int he BIOS should be set to "no" or "off" in
     order for PCI devices to work properly with FreeBSD.

     sf%d: couldn't map ports  A fatal initialization error has occurred.   This
     may  happen if the PCI BIOS not configured the device, which may be because
     the BIOS has been configured for a "Plug and Play" operating  system.   The
     "Plug  and  Play  OS" setting int he BIOS should be set to "no" or "off" in
     order for PCI devices to work properly with FreeBSD.

     sf%d: couldn't map interrupt  A fatal initialization error has occurred.

     sf%d: no memory for softc struct!	The driver failed to allocate memory for
     per-device instance information during initialization.

     sf%d: failed to enable I/O ports/memory mapping!  The driver failed to ini-
     tialize PCI I/O port or shared memory access.  This  might  happen  if  the
     card is not in a bus-master slot.

     sf%d:  watchdog  timeout  The device has stopped responding to the network,
     or there is a problem with the network connection (cable).

SEE ALSO
     arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

     The	 Adaptec	 AIC-6915	   Programmer's 	 Manual,
     ftp://ftp.adaptec.com/pub/BBS/userguides/aic6915_pg.pdf.

HISTORY
     The sf device driver first appeared in FreeBSD 3.0.

AUTHORS
     The sf driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

FreeBSD 5.2.1			  July 22, 1999 			   SF(4)

home | help