home | help
FXP(4)			     Kernel Interfaces Manual			  FXP(4)

NAME
     fxp -- Intel EtherExpress PRO/100 Ethernet device driver

SYNOPSIS
     device miibus
     device fxp

DESCRIPTION
     The  fxp  driver  provides support for Ethernet adapters based on the Intel
     i82557, i82558, i82559, i82550, and i82562 chips.

     The fxp driver supports the following media types:

     autoselect 	   Enable autoselection of the media type and options

     10baseT/UTP	   Set 10Mbps operation

     100baseTX		   Set 100Mbps (Fast Ethernet) operation

     The fxp driver supports the following media options:

     full-duplex	   Set full duplex operation

     Note that 100baseTX media type is not available on the Pro/10.  For further
     information on configuring this device, see ifconfig(8).

     The fxp driver also supports a special link option:

     link0  Some chip revisions have loadable microcode which can be used to re-
	    duce the interrupt load on the host cpu.  Not all  boards  have  mi-
	    crocode support.  Setting the link0 flag with ifconfig(8) will down-
	    load the microcode to the chip if it is available.

HARDWARE
     Adapters supported by the fxp driver include:

     *	 Intel EtherExpress PRO/10
     *	 Intel InBusiness 10/100
     *	 Intel PRO/100B / EtherExpressPRO/100 B PCI Adapter
     *	 Intel PRO/100+ Management Adapter
     *	 Intel PRO/100 VE Desktop Adapter
     *	 Intel PRO/100 M Desktop Adapter
     *	 Intel PRO/100 S Desktop, Server and Dual-Port Server Adapters
     *	 Contec C-NET(PI)-100TX (PC-98)
     *	 NEC PC-9821Ra20, Rv20, Xv13, Xv20 internal 100Base-TX (PC-98)
     *	 NEC PC-9821X-B06 (PC-98)
     *	 Many on-board network interfaces on Intel motherboards

DIAGNOSTICS
     fxp%d: couldn't map memory  A fatal initialization error has occurred.

     fxp%d: couldn't map interrupt  A fatal initialization error has occurred.

     fxp%d:  Failed  to malloc memory  There are not enough mbuf's available for
     allocation.

     fxp%d: device timeout  The device has stopped responding to the network, or
     there is a problem with the network connection (cable).

     fxp%d: Ethernet address ff:ff:ff:ff:ff:ff	In some Alpha's (AXPpci and Mul-
     tia) you must tell the driver to use (slower) I/O rather than memory to ac-
     cess the card.  Create, if it does not yet  exist,  and  add  to  the  file
     /boot/device.hints the line "hint.fxp.0.prefer_iomap="0"".

     fxp%d:  Microcode	loaded, int_delay: %d usec  bundle_max: %d  The chip has
     successfully downloaded the microcode, and changed the parameterized values
     to the given settings.

SEE ALSO
     arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY
     The fxp device driver first appeared in FreeBSD 2.1.

AUTHORS
     The fxp device driver was written by David Greenman.  It has then been  up-
     dated  to use the busdma API and made endian-clean by Maxime Henrion.  This
     manual page was written by David E. O'Brien.

FreeBSD 5.3			  July 4, 2004				  FXP(4)

home | help