home | help
WB(4)			     Kernel Interfaces Manual			   WB(4)

NAME
     wb -- Winbond W89C840F Fast Ethernet device driver

SYNOPSIS
     device miibus
     device wb

DESCRIPTION
     The  wb driver provides support for PCI Ethernet adapters and embedded con-
     trollers based on the Winbond W89C840F Fast Ethernet controller chip.   The
     840F  should  not	be  confused with the 940F, which is an NE2000 clone and
     only supports 10Mbps speeds.

     The Winbond controller uses bus master DMA and is	designed  to  be  a  DEC
     'tulip'  workalike.   It  differs	from  the standard DEC design in several
     ways: the control and status registers are spaced 4 bytes apart instead  of
     8,  and  the  receive filter is programmed through registers rather than by
     downloading a special setup frame via the transmit DMA  engine.   Using  an
     external  PHY,  the Winbond chip supports both 10 and 100Mbps speeds in ei-
     ther full or half duplex.

     The wb driver supports the following media types:

     autoselect 	   Enable autoselection of the media type  and	options.
			   This  is  only  supported if the PHY chip attached to
			   the Winbond controller supports NWAY autonegotiation.
			   The user can manually override the autoselected  mode
			   by adding media options to the /etc/rc.conf file.

     10baseT/UTP	   Set	10Mbps	operation.  The mediaopt option can also
			   be used to select either full-duplex  or  half-duplex
			   modes.

     100baseTX		   Set	100Mbps (Fast Ethernet) operation.  The mediaopt
			   option can also be used to select either  full-duplex
			   or half-duplex modes.

     The wb driver supports the following media options:

     full-duplex	   Force full duplex operation

     half-duplex	   Force half duplex operation.

     Note  that  the  100baseTX media type is only available if supported by the
     adapter.  For more information on configuring this device, see ifconfig(8).

HARDWARE
     The wb driver supports Winbond W89C840F based Fast  Ethernet  adapters  and
     embedded controllers including:

     *	 Trendware TE100-PCIE

DIAGNOSTICS
     wb%d: couldn't map memory	A fatal initialization error has occurred.

     wb%d: couldn't map interrupt  A fatal initialization error has occurred.

     wb%d:  watchdog  timeout  The device has stopped responding to the network,
     or there is a problem with the network connection (cable).

     wb%d: no memory for rx list  The driver failed to allocate an mbuf for  the
     receiver ring.

     wb%d:  no memory for tx list  The driver failed to allocate an mbuf for the
     transmitter ring when allocating a pad buffer or collapsing an  mbuf  chain
     into a cluster.

     wb%d: chip is in D3 power state -- setting to D0  This message applies only
     to  adapters  which support power management.  Some operating systems place
     the controller in low power mode when shutting down, and  some  PCI  BIOSes
     fail  to  bring the chip out of this state before configuring it.	The con-
     troller loses all of its PCI configuration in the D3 state, so if the  BIOS
     does  not	set it back to full power mode in time, it won't be able to con-
     figure it correctly.  The driver tries to detect this condition  and  bring
     the  adapter  back to the D0 (full power) state, but this may not be enough
     to return the driver to a fully operational condition.   If  you  see  this
     message at boot time and the driver fails to attach the device as a network
     interface,  you  will  have  to perform second warm boot to have the device
     properly configured.

     Note that this condition only occurs when warm booting from another operat-
     ing system.  If you power down your system prior to  booting  FreeBSD,  the
     card should be configured correctly.

SEE ALSO
     arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY
     The wb device driver first appeared in FreeBSD 3.0.

AUTHORS
     The wb driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

BUGS
     The  Winbond  chip  seems	to  behave strangely in some cases when the link
     partner switches modes.  If for example both sides are set to 10Mbps  half-
     duplex,  and the other end is changed to 100Mbps full-duplex, the Winbond's
     receiver suddenly starts writing trash all over the RX descriptors.  The wb
     driver handles this by forcing a reset of both the controller chip and  at-
     tached  PHY.  This is drastic, but it appears to be the only way to recover
     properly from this condition.

FreeBSD 5.4			September 4, 2004			   WB(4)

home | help