home | help
AXE(4)			     Kernel Interfaces Manual			  AXE(4)

NAME
     axe -- ASIX Electronics AX88172 USB Ethernet driver

SYNOPSIS
     To compile this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device ehci
	   device uhci
	   device ohci
	   device usb
	   device miibus
	   device axe

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_axe_load="YES"

DESCRIPTION
     The axe driver provides support for USB Ethernet adapters based on the ASIX
     Electronics AX88172 USB 2.0 chipset.

     The  AX88172  is a USB 2.0 device which contains a 10/100 Ethernet MAC with
     MII interface and is designed to work with both Ethernet and HomePNA trans-
     ceivers.  The AX88172 will operate with both  USB	1.x  and  USB  2.0  con-
     trollers,	however  performance  with 1.x controllers will be limited since
     the USB 1.x standard specifies a maximum transfer speed of  12Mbps.   Users
     with  USB	1.x  controllers should therefore not expect to actually achieve
     100Mbps speeds with these devices.

     The AX88172 supports a 64-bit multicast hash table, single  perfect  filter
     entry  for  the  station  address, all-multicast mode and promiscuous mode.
     Packets are received and transmitted over separate USB bulk  transfer  end-
     points.

     The axe driver supports the following media types:

     autoselect   Enable  autoselection of the media type and options.	The user
		  can manually override the autoselected mode  by  adding  media
		  options to the /etc/rc.conf file.

     10baseT/UTP  Set 10Mbps operation.  The mediaopt option can also be used to
		  enable  full-duplex operation.  Not specifying full-duplex im-
		  plies half-duplex mode.

     100baseTX	  Set 100Mbps (Fast Ethernet) operation.   The	mediaopt  option
		  can  also be used to enable full-duplex operation.  Not speci-
		  fying full-duplex implies half-duplex mode.

     The axe driver supports the following media options:

     full-duplex  Force full duplex operation.	The interface  will  operate  in
		  half duplex mode if this media option is not specified.

     For more information on configuring this device, see ifconfig(8).

HARDWARE
     The  axe  driver  supports  ASIX  Electronics  AX88172  based  USB Ethernet
     adapters including:

     *	 Buffalo (Melco Inc.) LUA-U2-KTX
     *	 D-Link DUB-E100, revision A
     *	 LinkSys USB200M
     *	 Netgear FA120
     *	 Sitecom LN-029
     *	 System TALKS Inc. SGC-X2UL

DIAGNOSTICS
     axe%d: watchdog timeout  A packet was queued for transmission and a  trans-
     mit command was issued, however the device failed to acknowledge the trans-
     mission before a timeout expired.

     axe%d: no memory for rx list  The driver failed to allocate an mbuf for the
     receiver ring.

SEE ALSO
     altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

     ASIX AX88172 data sheet, http://www.asix.com.tw.

HISTORY
     The axe device driver first appeared in FreeBSD 5.0.

AUTHORS
     The axe driver was written by Bill Paul <wpaul@windriver.com>.

FreeBSD 6.3			  June 6, 2007				  AXE(4)

home | help