home | help
EM(4)			     Kernel Interfaces Manual			   EM(4)

NAME
     em -- Intel(R) PRO/1000 Gigabit Ethernet adapter driver

SYNOPSIS
     To compile this driver into the kernel, place the following line in your
     kernel configuration file:

	   device em

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_em_load="YES"

DESCRIPTION
     The  em  driver provides support for PCI Gigabit Ethernet adapters based on
     the Intel 82540, 82541ER,	82541PI,  82542,  82543,  82544,  82545,  82546,
     82546EB,  82546GB, 82547, 82571, 81572 and 82573 Ethernet controller chips.
     The driver supports Transmit/Receive checksum offload and Jumbo Frames only
     on 82540, 82543, 82544 and 82546-based adapters.  For further hardware  in-
     formation, see the README included with the driver.

     For  questions related to hardware requirements, refer to the documentation
     supplied with your  Intel	PRO/1000  adapter.   All  hardware  requirements
     listed apply to use with FreeBSD.

     Support  for  Jumbo  Frames is provided via the interface MTU setting.  Se-
     lecting an MTU larger than 1500 bytes with the ifconfig(8) utility  config-
     ures  the	adapter  to  receive and transmit Jumbo Frames.  The maximum MTU
     size for Jumbo Frames is 16114.

     This driver version supports VLANs.  For information on enabling VLANs, see
     the README.  The em driver supports the following media types:

     autoselect   Enables auto-negotiation for speed and duplex.

     10baseT/UTP  Sets 10Mbps operation.  Use  the  mediaopt  option  to  select
		  full-duplex mode.

     100baseTX	  Sets	100Mbps  operation.   Use  the mediaopt option to select
		  full-duplex mode.

     1000baseSX   Sets 1000Mbps operation.  Only full-duplex mode  is  supported
		  at this speed.

     1000baseTX   Sets	1000Mbps  operation.  Only full-duplex mode is supported
		  at this speed.

     The em driver supports the following media options:

     full-duplex  Forces full-duplex operation

     half-duplex  Forces half-duplex operation.

     Only use mediaopt to set the driver to full-duplex.   If  mediaopt  is  not
     specified, the driver defaults to half-duplex.

     For more information on configuring this device, see ifconfig(8).

HARDWARE
     The  em driver supports Gigabit Ethernet adapters based on the Intel 82540,
     82541ER, 82541PI, 82542, 82543,  82544,  82545,  82546,  82546EB,	82546GB,
     82547, 82571, 82572 and 82573 controller chips:

     *	 Intel PRO/1000 CT Network Connection (82547)
     *	 Intel PRO/1000 F Server Adapter (82543)
     *	 Intel PRO/1000 Gigabit Server Adapter (82542)
     *	 Intel PRO/1000 GT Desktop Adapter (82541PI)
     *	 Intel PRO/1000 MF Dual Port Server Adapter (82546)
     *	 Intel PRO/1000 MF Server Adapter (82545)
     *	 Intel PRO/1000 MF Server Adapter (LX) (82545)
     *	 Intel PRO/1000 MT Desktop Adapter (82540)
     *	 Intel PRO/1000 MT Desktop Adapter (82541)
     *	 Intel PRO/1000 MT Dual Port Server Adapter (82546)
     *	 Intel PRO/1000 MT Quad Port Server Adapter (82546EB)
     *	 Intel PRO/1000 MT Server Adapter (82545)
     *	 Intel PRO/1000 T Desktop Adapter (82544)
     *	 Intel PRO/1000 T Server Adapter (82543)
     *	 Intel PRO/1000 XF Server Adapter (82544)
     *	 Intel PRO/1000 XT Server Adapter (82544)

LOADER TUNABLES
     Tunables  can  be	set at the loader(8) prompt before booting the kernel or
     stored in loader.conf(5).

     hw.em.rxd
	     Number of receive descriptors allocated by the driver.  The default
	     value is 256.  The 82542 and 82543-based adapters can handle up  to
	     256 descriptors, while others can have up to 4096.

     hw.em.txd
	     Number  of  transmit  descriptors allocated by the driver.  The de-
	     fault value is 256.  The 82542 and 82543-based adapters can  handle
	     up to 256 descriptors, while others can have up to 4096.

     hw.em.rx_int_delay
	     This  value delays the generation of receive interrupts in units of
	     1.024 microseconds.  The default value is	0,  since  adapters  may
	     hang with this feature being enabled.

     hw.em.rx_abs_int_delay
	     If  hw.em.rx_int_delay is non-zero, this tunable limits the maximum
	     delay in which a receive interrupt is generated.

     hw.em.tx_int_delay
	     This value delays the generation of transmit interrupts in units of
	     1.024 microseconds.  The default value is 64.

     hw.em.tx_abs_int_delay
	     If hw.em.tx_int_delay is non-zero, this tunable limits the  maximum
	     delay in which a transmit interrupt is generated.

DIAGNOSTICS
     em%d: Unable to allocate bus resource: memory  A fatal initialization error
     has occurred.

     em%d:  Unable  to	allocate bus resource: interrupt  A fatal initialization
     error has occurred.

     em%d: watchdog timeout -- resetting  The device has stopped  responding  to
     the network, or there is a problem with the network connection (cable).

SUPPORT
     For  additional  information  regarding  building and installation, see the
     README included with the driver.  For general information and  support,  go
     to the Intel support website at: http://support.intel.com.

     If  an  issue  is identified with the released source code on the supported
     kernel with a supported adapter, email the specific information related  to
     the issue to <freebsdnic@mailbox.intel.com>.

SEE ALSO
     altq(4), arp(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)

HISTORY
     The em device driver first appeared in FreeBSD 4.4.

AUTHORS
     The      em     driver	was	written     by	   Intel     Corporation
     <freebsdnic@mailbox.intel.com>.

BUGS
     Hardware-assisted VLAN processing is disabled by default.	You  can  enable
     it on an em interface using ifconfig(8).

FreeBSD 6.3			November 27, 2005			   EM(4)

home | help