home | help
ALE(4)			     Kernel Interfaces Manual			  ALE(4)

NAME
     ale -- Atheros AR8121/AR8113/AR8114 Gigabit/Fast Ethernet driver

SYNOPSIS
     To compile this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device miibus
	   device ale

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_ale_load="YES"

DESCRIPTION
     The ale device driver provides support for Atheros AR8121 PCI Express Giga-
     bit Ethernet controller and Atheros AR8113/AR8114 PCI Express Fast Ethernet
     controllers.

     All  LOMs	supported by the ale driver have TCP/UDP/IP checksum offload for
     both receive and transmit, TCP segmentation offload  (TSO),  hardware  VLAN
     tag  stripping/insertion  features, Wake On Lan (WOL) and an interrupt coa-
     lescing/moderation mechanism as well as a 64-bit multicast hash filter.

     The AR8121 also supports Jumbo Frames (up to 8132 bytes), which can be con-
     figured via the interface MTU setting.  Selecting an MTU larger  than  1500
     bytes  with  the  ifconfig(8) utility configures the adapter to receive and
     transmit Jumbo Frames.

     The ale driver supports the following media types:

     autoselect   Enable autoselection of the media type and options.  The  user
		  can  manually  override  the autoselected mode by adding media
		  options to rc.conf(5).

     10baseT/UTP  Set 10Mbps operation.

     100baseTX	  Set 100Mbps (Fast Ethernet) operation.

     1000baseTX   Set 1000baseTX operation over twisted pair.

     The ale driver supports the following media options:

     full-duplex  Force full duplex operation.

     half-duplex  Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

HARDWARE
     The ale device driver provides support  for  the  following  Ethernet  con-
     trollers:

     *	 Atheros AR8113 PCI Express Fast Ethernet controller
     *	 Atheros AR8114 PCI Express Fast Ethernet controller
     *	 Atheros AR8121 PCI Express Gigabit Ethernet controller

LOADER TUNABLES
     Tunables  can  be	set at the loader(8) prompt before booting the kernel or
     stored in loader.conf(5).

     hw.ale.msi_disable
	     This tunable disables MSI support on the  Ethernet  hardware.   The
	     default value is 0.

     hw.ale.msix_disable
	     This  tunable disables MSI-X support on the Ethernet hardware.  The
	     default value is 0.

SYSCTL VARIABLES
     The following variables are  available  as  both  sysctl(8)  variables  and
     loader(8) tunables:

     dev.ale.%d.int_rx_mod
	     Maximum  amount  of  time	to delay receive interrupt processing in
	     units of 1us.  The accepted range is 0 to 130000,	the  default  is
	     30(30us).	Value 0 completely disables the interrupt moderation.

     dev.ale.%d.int_tx_mod
	     Maximum  amount  of  time to delay transmit interrupt processing in
	     units of 1us.  The accepted range is 0 to 130000,	the  default  is
	     1000(1ms).  Value 0 completely disables the interrupt moderation.

     dev.ale.%d.process_limit
	     Maximum  amount  of Rx frames to be processed in the event loop be-
	     fore rescheduling a taskqueue.  The accepted range is  32	to  255,
	     the default value is 128 events.  The interface does not need to be
	     brought down and up again before a change takes effect.

SEE ALSO
     altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), vlan(4), ifconfig(8)

HISTORY
     The  ale  driver  was  written by Pyun YongHyeon <yongari@FreeBSD.org>.  It
     first appeared in FreeBSD 7.1.

FreeBSD 7.1			November 12, 2008			  ALE(4)

home | help