home | help
ISP(4)			     Kernel Interfaces Manual			  ISP(4)

NAME
     isp -- Qlogic based SCSI and FibreChannel SCSI Host Adapters

SYNOPSIS
     To compile this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device scbus
	   device isp

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):

	   isp_load="YES"

DESCRIPTION
     This driver provides access to SCSI or FibreChannel devices.

     SCSI features include support for Ultra SCSI and wide mode transactions for
     SCSI,  Ultra2  LVD  (for  the ISP1080 and ISP1280), and Ultra3 LVD (for the
     ISP12160).

     Fibre Channel support uses FCP SCSI profile for FibreChannel.  and utilizes
     Class 3 and Class 2 connections (Qlogic 2100 is Class 3 only, minor patches
     to the Qlogic 2200 to force Class 2 mode).  Support is available for Public
     and Private loops, and for point-to-point connections (Qlogic  2200  only).
     The newer 2-Gigabit cards (2300, 2312, 2322) and 4-Gigabit (2422, 2432) are
     also   supported.	  Command   tagging  is  supported  for  all  (in  fact,
     FibreChannel requires tagging).  Fabric support is enabled by  default  for
     other  than 2100 cards.  Fabric support for 2100 cards has been so problem-
     atic and these cards are so old now that it is just not worth your time  to
     try it.

FIRMWARE
     Firmware  is  available  if  the ispfw(4) module is loaded during bootstrap
     (q.v.).

     It is strongly  recommended  that	you  use  the  firmware  available  from
     ispfw(4) as it is the most likely to have been tested with this driver.

HARDWARE
     Cards supported by the isp driver include:

	   ISP1000
		   SBus  Fast  Wide, Ultra Fast Wide cards, Single Ended or Dif-
		   ferential cards.

	   ISP1020
		   Qlogic 1020 Fast Wide and Differential Fast Wide PCI cards.

	   ISP1040
		   Qlogic 1040 Ultra Wide and Differential Ultra Wide PCI cards.
		   Also known as the DEC KZPBA-CA (single  ended)  and	KZPBA-CB
		   (HVD differential).

	   Qlogic 1240
		   Qlogic  1240  Dual Bus Ultra Wide and Differential Ultra Wide
		   PCI cards.

	   Qlogic 1020
		   Qlogic 1020 SCSI cards.

	   Qlogic 1040
		   Qlogic 1040 Ultra SCSI cards.

	   Qlogic 1080
		   Qlogic 1280 LVD Ultra2 Wide PCI cards.

	   Qlogic 1280
		   Qlogic 1280 Dual Bus LVD Ultra2 Wide PCI cards.

	   Qlogic 12160
		   Qlogic 12160 Dual Bus LVD Ultra3 Wide PCI cards.

	   Qlogic 210X
		   Qlogic 2100 and 2100A Copper and Optical Fibre Channel  Arbi-
		   trated Loop (single, dual).

	   Qlogic 220X
		   Qlogic  2200 Copper and Optical Fibre Channel Arbitrated Loop
		   PCI cards (single, dual, quad).

	   Qlogic 2300
		   Qlogic 2300 Optical Fibre Channel PCI cards.

	   Qlogic 2312
		   Qlogic 2312 Optical Fibre Channel PCI cards.

	   Qlogic 234X
		   Qlogic 234X Optical Fibre Channel PCI  cards  (2312	chipset,
		   single and dual attach).

	   Qlogic 2322
		   Qlogic 2322 Optical Fibre Channel PCIe cards.

	   Qlogic 200
		   Dell  Branded  version  of  the QLogic 2312 Fibre Channel PCI
		   cards.

	   Qlogic 2422
		   Qlogic 2422 Optical Fibre Channel PCI cards (4 Gigabit)

	   Qlogic 2432
		   Qlogic 2432 Optical Fibre Channel PCIe cards (4 Gigabit)

CONFIGURATION OPTIONS
     Target mode support may be enabled with the

     options ISP_TARGET_MODE

     option.

BOOT OPTIONS
     The   following   options	 are   switchable   by	 setting    values    in
     /boot/device.hints.

     They are:

     hint.isp.0.disable
	     A hint value to disable driver in kernel.

     hint.isp.0.fwload_disable
	     A hint value to disable loading of firmware ispfw(4).

     hint.isp.0.prefer_memmap
	     A	hint  value  to use PCI memory space instead of I/O space access
	     for.

     hint.isp.0.prefer_iomap
	     A hint value to use PCI I/O space instead of  Memory  space  access
	     for.

     hint.isp.0.ignore_nvram
	     A	hint  value  to  ignore board NVRAM settings for.  Otherwise use
	     NVRAM settings.

     hint.isp.0.fullduplex
	     A hint value to set full duplex mode.

     hint.isp.0.topology
	     A hint value to select topology of  connection.   Supported  values
	     are:

	     lport	 Prefer loopback and fallback to point to point.
	     nport	 Prefer point to point and fallback to loopback.
	     lport-only  Loopback only.
	     nport-only  Point to point only.

     hint.isp.0.portwwn
	     This  should be the full 64 bit World Wide Port Name you would like
	     to use, overriding the value in NVRAM for the card.

     hint.isp.0.nodewwn
	     This should be the full 64 bit World Wide Node Name you would  like
	     to use, overriding the value in NVRAM for the card.

     hint.isp.0.iid
	     A	hint  to override or set the Initiator ID or Loop ID.  For Fibre
	     Channel cards in Local Loop topologies it is  strongly  recommended
	     that you set this value to non-zero.

     hint.isp.0.role
	     A	hint to define default role for isp instance (target, initiator,
	     both).

     hint.isp.0.debug
	     A	hint  value  for  a   driver   debug   level   (see   the   file
	     /usr/src/sys/dev/isp/ispvar.h for the values.

SYSCTL OPTIONS
     dev.isp.N.loop_down_limit
	     This  value  says	how  long to wait in seconds after loop has gone
	     down before giving up and expiring all of	the  devices  that  were
	     visible.  The default is 300 seconds (5 minutes).	A separate (non-
	     adjustable)  timeout  is  used  when booting to not stop booting on
	     lack of FC connectivity.

     dev.isp.N.gone_device_time
	     This value says how long to wait for devices to  reappear	if  they
	     (temporarily)  disappear  due to loop or fabric events.  While this
	     timeout is running, I/O to those devices will simply be held.

     dev.isp.N.wwnn
	     This is the readonly World Wide Node Name value for this port.

     dev.isp.N.wwpn
	     This is the readonly World Wide Port Name value for this port.

SEE ALSO
     da(4), intro(4), ispfw(4), sa(4), scsi(4)

AUTHORS
     The isp driver was written  by  Matthew  Jacob  originally  for  NetBSD  at
     NASA/Ames Research Center.

BUGS
     The driver currently ignores some NVRAM settings.

     Target  mode  support  is not completely reliable yet.  It works reasonably
     well for Fibre Channel, somewhat well for Qlogic 1040 cards, but  does  not
     yet  work	for  the  other cards (due to last minute unannounced changes in
     firmware interfaces).

FreeBSD 7.4			February 28, 2007			  ISP(4)

home | help