VLAN(4) Kernel Interfaces Manual VLAN(4) NAME vlan -- IEEE 802.1Q VLAN network interface SYNOPSIS To compile this driver into the kernel, place the following lines in your kernel configuration file: device vlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_vlan_load="YES" DESCRIPTION The vlan driver demultiplexes frames tagged according to the IEEE 802.1Q standard into logical vlan network interfaces, which allows routing/bridg- ing between multiple VLANs through a single switch trunk port. Each vlan interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). To function, a vlan interface must be assigned a parent interface and nu- meric VLAN tag using ifconfig(8). A single parent can be assigned to mul- tiple vlan interfaces provided they have different tags. The parent inter- face is likely to be an Ethernet card connected to a properly configured switch port. The VLAN tag should match one of those set up in the switched network. Initially vlan assumes the same minimum length for tagged and untagged frames. This mode is selected by the sysctl(8) variable net.link.vlan.soft_pad set to 0 (default). However, there are network de- vices that fail to adjust frame length, should it fall below the allowed minimum due to untagging. Such devices should be able to interoperate with vlan after changing the value of net.link.vlan.soft_pad to 1. In the lat- ter mode, vlan will pad short frames before tagging them so that their length stays not less than the minimum value after untagging by the non- compliant devices. HARDWARE The vlan driver supports efficient operation over parent interfaces that can provide help in processing VLANs. Such interfaces are automatically recognized by their capabilities. Depending on the level of sophistication found in a physical interface, it may do full VLAN processing or just be able to receive and transmit long frames (up to 1522 bytes including an Ethernet header and FCS). The capabilities may be user-controlled by the respective parameters to ifconfig(8), vlanhwtag and vlanmtu. However, a physical interface is not obliged to react to them: It may have either ca- pability enabled permanently without a way to turn it off. The whole issue is very specific to a particular device and its driver. By now, the list of physical interfaces able of full VLAN processing in the hardware is limited to the following devices: ae(4), age(4), alc(4), ale(4), bce(4), bge(4), cxgb(4), em(4), ixgb(4), jme(4), msk(4), nge(4), re(4), sge(4), stge(4), ti(4), txp(4), and vge(4). The rest of the Ethernet interfaces can run VLANs using software emulation in the vlan driver. However, some of them lack the capability of transmit- ting and receiving long frames. Assigning such an interface as the parent to vlan will result in a reduced MTU on the corresponding vlan interfaces. In the modern Internet, this is likely to cause tcp(4) connectivity prob- lems due to massive, inadequate icmp(4) filtering that breaks the Path MTU Discovery mechanism. The following interfaces support long frames for vlan natively: bfe(4), cas(4), dc(4), fwe(4), fxp(4), gem(4), hme(4), le(4), nfe(4), nve(4), rl(4), sf(4), sis(4), sk(4), ste(4), tl(4), tx(4), vr(4), and xl(4). The vlan driver automatically recognizes devices that natively support long frames for vlan use and calculates the appropriate frame MTU based on the capabilities of the parent interface. Some other interfaces not listed above may handle long frames, but they do not advertise this ability of theirs. The MTU setting on vlan can be corrected manually if used in con- junction with such a parent interface. SEE ALSO ifconfig(8), sysctl(8) BUGS No 802.1Q features except VLAN tagging are implemented. FreeBSD 8.1 April 14, 2010 VLAN(4)
Want to link to this manual page? Use this URL:
<https://man.FreeBSD.org/cgi/man.cgi?query=vlan&sektion=4&manpath=FreeBSD+8.1-RELEASE>