home | help
RC.CONF(5)		       File Formats Manual		      RC.CONF(5)

NAME
     rc.conf -- system configuration information

DESCRIPTION
     The  file	rc.conf  contains  descriptive	information about the local host
     name, configuration details for any potential network interfaces and  which
     services  should be started up at system initial boot time.  In new instal-
     lations, the rc.conf file is generally initialized by the system  installa-
     tion utility, sysinstall(8).

     The purpose of rc.conf is not to run commands or perform system startup ac-
     tions  directly.	Instead,  it  is included by the various generic startup
     scripts in /etc which conditionalize their internal  actions  according  to
     the settings found there.

     The  /etc/rc.conf	file  is  included  from the file /etc/defaults/rc.conf,
     which specifies the default settings for all the  available  options.   Op-
     tions  need only be specified in /etc/rc.conf when the system administrator
     wishes to override these defaults.  The file /etc/rc.conf.local is used  to
     override  settings  in /etc/rc.conf for historical reasons.  In addition to
     /etc/rc.conf.local you can also place smaller configuration files for  each
     rc(8) script in the /etc/rc.conf.d directory, which will be included by the
     load_rc_config  function.	 For  jail configurations you could use the file
     /etc/rc.conf.d/jail to store jail specific configuration options.	Also see
     the rc_conf_files variable below.

     Options are set with "name=value" assignments that use sh(1)  syntax.   The
     following list provides a name and short description for each variable that
     can be set in the rc.conf file:

     rc_debug	 (bool) If set to "YES", enable output of debug messages from rc
		 scripts.   This  variable can be helpful in diagnosing mistakes
		 when editing or integrating new scripts.  Beware that this pro-
		 duces copious output to the terminal and syslog(3).

     rc_info	 (bool) If set to "NO", disable informational messages from  the
		 rc scripts.  Informational messages are displayed when a condi-
		 tion  that is not serious enough to warrant a warning or an er-
		 ror occurs.

     rc_startmsgs
		 (bool) If set to "YES", show "Starting foo:" when faststart  is
		 used (e.g., at boot time).

     early_late_divider
		 (str)	The name of the script that should be used as the delim-
		 iter between the "early" and "late" stages of the boot process.
		 The early stage should contain all the services needed  to  get
		 the  disks (local or remote) mounted so that the late stage can
		 include scripts contained in  the  directories  listed  in  the
		 local_startup	variable (see below).  Thus, the two likely can-
		 didates for this value are mountcritlocal for the typical  sys-
		 tem,  and  mountcritremote if the system needs remote file sys-
		 tems mounted to get access to	the  local_startup  directories;
		 for example when /usr/local is NFS mounted.  For rc.conf within
		 a jail(8) NETWORKING is likely to be an appropriate value.  Ex-
		 treme care should be taken when changing this value, and before
		 changing  it  one  should ensure that there are adequate provi-
		 sions to recover from a failed boot (such as  physical  contact
		 with the machine, or reliable remote console access).

     swapfile	 (str)	If  set to "NO", no swapfile is installed, otherwise the
		 value is used as the full pathname to a file to use  for  addi-
		 tional swap space.

     apm_enable  (bool) If set to "YES", enable support for Automatic Power Man-
		 agement with the apm(8) command.

     apmd_enable
		 (bool)  Run  apmd(8)  to  handle APM event from userland.  This
		 also enables support for APM.

     apmd_flags  (str) If apmd_enable is set to "YES", these are  the  flags  to
		 pass to the apmd(8) daemon.

     devd_enable
		 (bool)  Run  devd(8) to handle device added, removed or unknown
		 events from the kernel.

     ddb_enable  (bool) Run ddb(8) to install ddb(4) scripts at boot time.

     ddb_config  (str) Configuration file for ddb(8).  Default /etc/ddb.conf.

     kld_list	 (str) A list of kernel modules to load right  after  the  local
		 disks	are  mounted.  Loading modules at this point in the boot
		 process is much faster than doing it via /boot/loader.conf  for
		 those modules not necessary for mounting local disk.

     kldxref_enable
		 (bool)  Set  to "NO" by default.  Set to "YES" to automatically
		 rebuild linker.hints files with kldxref(8) at boot time.

     kldxref_clobber
		 (bool) Set to "NO" by default.  If kldxref_enable is true, set-
		 ting to "YES" will overwrite  existing  linker.hints  files  at
		 boot time.  Otherwise, only missing linker.hints files are gen-
		 erated.

     kldxref_module_path
		 (str)	Empty  by default.  A semi-colon (`;') delimited list of
		 paths containing kld(4) modules.  If empty, the contents of the
		 kern.module_path sysctl(8) are used.

     powerd_enable
		 (bool) If set to "YES", enable the system power control  facil-
		 ity with the powerd(8) daemon.

     powerd_flags
		 (str)	If powerd_enable is set to "YES", these are the flags to
		 pass to the powerd(8) daemon.

     tmpmfs	 Controls the creation of a /tmp  memory  file	system.   Always
		 happens  if  set to "YES" and never happens if set to "NO".  If
		 set to anything else, a memory file system is created	if  /tmp
		 is not writable.

     tmpsize	 Controls the size of a created /tmp memory file system.

     tmpmfs_flags
		 Extra	options  passed  to the mdmfs(8) utility when the memory
		 file system for /tmp is created.  The default	is  "-S",  which
		 inhibits  the	use  of  softupdates on /tmp so that file system
		 space is freed without delay after file truncation or deletion.
		 See mdmfs(8) for other options you can use in tmpmfs_flags.

     varmfs	 Controls the creation of a /var  memory  file	system.   Always
		 happens  if  set to "YES" and never happens if set to "NO".  If
		 set to anything else, a memory file system is created	if  /var
		 is not writable.

     varsize	 Controls the size of a created /var memory file system.

     varmfs_flags
		 Extra	options  passed  to the mdmfs(8) utility when the memory
		 file system for /var is created.  The default	is  "-S",  which
		 inhibits  the	use  of  softupdates on /var so that file system
		 space is freed without delay after file truncation or deletion.
		 See mdmfs(8) for other options you can use in varmfs_flags.

     populate_var
		 Controls the automatic population of the /var file system.  Al-
		 ways happens if set to "YES" and never happens if set to  "NO".
		 If  set  to  anything	else, a memory file system is created if
		 /var is not writable.	Note that this process	requires  access
		 to  certain  commands	in /usr before /usr is mounted on normal
		 systems.

     cleanvar_enable
		 (bool) Clean the /var directory.

     local_startup
		 (str) List of directories to search for startup script files.

     script_name_sep
		 (str) The field separator to use for breaking down the list  of
		 startup script files into individual filenames.  The default is
		 a  space.   It is not necessary to change this unless there are
		 startup scripts with names containing spaces.

     hostapd_enable
		 (bool) Set to "YES" to start hostapd(8) at system boot time.

     hostname	 (str) The fully qualified domain name (FQDN) of  this	host  on
		 the  network.	This should almost certainly be set to something
		 meaningful,  even  if	there  is  no  network	connection.   If
		 dhclient(8) is used to set the hostname via DHCP, this variable
		 should  be set to an empty string.  If this value remains unset
		 when the system is done booting your console login will display
		 the default hostname of "Amnesiac."

     nisdomainname
		 (str) The NIS domain name of this host, or "NO" if NIS  is  not
		 used.

     dhclient_program
		 (str)	Path  to  the  DHCP  client program (/sbin/dhclient, the
		 OpenBSD DHCP client, is the default).

     dhclient_flags
		 (str) Additional flags to pass to the DHCP client program.  For
		 the OpenBSD DHCP client, see the dhclient(8) manpage for a  de-
		 scription of the command line options available.

     dhclient_flags_<iface>
		 Additional  flags to pass to the DHCP client program running on
		 iface	only.	 When	specified,   this   variable   overrides
		 dhclient_flags.

     background_dhclient
		 (bool)  Set  to  "YES"  to start the DHCP client in background.
		 This can cause trouble with applications depending on a working
		 network, but it will provide a faster startup in many cases.

     background_dhclient_<iface>
		 When specified, this variable overrides the background_dhclient
		 variable for interface iface only.

     synchronous_dhclient
		 (bool) Set to	"YES"  to  start  dhclient(8)  synchronously  at
		 startup.   This  behavior  can be overridden on a per-interface
		 basis	 by   replacing    the	  "DHCP"    keyword    in    the
		 ifconfig_<interface> variable with "SYNCDHCP" or "NOSYNCDHCP".

     defaultroute_delay
		 (int)	When set to a positive value, wait up to this long after
		 configuring DHCP interfaces at startup to give  the  interfaces
		 time to receive a lease.

     firewall_enable
		 (bool)  Set to "YES" to load firewall rules at startup.  If the
		 kernel was not built with options IPFIREWALL, the ipfw.ko  ker-
		 nel module will be loaded.  See also ipfilter_enable.

     firewall_script
		 (str)	This  variable	specifies  the full path to the firewall
		 script to run.  The default is /etc/rc.firewall.

     firewall_type
		 (str)	Names  the  firewall  type   from   the   selection   in
		 /etc/rc.firewall, or the file which contains the local firewall
		 ruleset.  Valid selections from /etc/rc.firewall are:

		 open	 unrestricted IP access
		 closed  all IP services disabled, except via "lo0"
		 client  basic protection for a workstation
		 simple  basic protection for a LAN.

		 If a filename is specified, the full path must be given.

     firewall_quiet
		 (bool) Set to "YES" to disable the display of firewall rules on
		 the console during boot.

     firewall_logging
		 (bool)  Set to "YES" to enable firewall event logging.  This is
		 equivalent to the IPFIREWALL_VERBOSE kernel option.

     firewall_flags
		 (str) Flags passed to	ipfw(8)  if  firewall_type  specifies  a
		 filename.

     firewall_coscripts
		 (str)	List of executables and/or rc scripts to run after fire-
		 wall starts/stops.  Default is empty.

     firewall_nat_enable
		 (bool) The ipfw(8) equivalent of natd_enable.	Setting this  to
		 "YES"	enables kernel NAT.  firewall_enable must also be set to
		 "YES".

     firewall_nat_interface
		 (str) The ipfw(8) equivalent of natd_interface.   This  is  the
		 name  of the public interface or IP address on which kernel NAT
		 should run.

     firewall_nat_flags
		 (str) Additional configuration parameters for kernel NAT should
		 be placed here.

     dummynet_enable
		 (bool) Setting this to "YES" will automatically load  the  dum-
		 mynet(4) module if firewall_enable is also set to "YES".

     natd_program
		 (str) Path to natd(8).

     natd_enable
		 (bool)  Set  to  "YES" to enable natd(8).  firewall_enable must
		 also be set to "YES", and divert(4) sockets must be enabled  in
		 the kernel.  If the kernel was not built with options IPDIVERT,
		 the ipdivert.ko kernel module will be loaded.

     natd_interface
		 (str) This is the name of the public interface on which natd(8)
		 should run.  The interface may be given as an interface name or
		 as an IP address.

     natd_flags  (str)	Additional  natd(8) flags should be placed here.  The -n
		 or -a flag is automatically added with the above natd_interface
		 as an argument.

     ipfilter_enable
		 (bool) Set to "NO" by default.  Setting this to  "YES"  enables
		 ipf(8) packet filtering.

		 Typical usage will require putting

		 ipfilter_enable="YES"
		 ipnat_enable="YES"
		 ipmon_enable="YES"
		 ipfs_enable="YES"

		 into	 /etc/rc.conf	 and	editing    /etc/ipf.rules    and
		 /etc/ipnat.rules appropriately.

		 Note that ipfilter_enable and ipnat_enable can be enabled inde-
		 pendently.  ipmon_enable and ipfs_enable both require at  least
		 one of ipfilter_enable and ipnat_enable to be enabled.

		 Having

		 options IPFILTER
		 options IPFILTER_LOG
		 options IPFILTER_DEFAULT_BLOCK

		 in the kernel configuration file is a good idea, too.

     ipfilter_program
		 (str) Path to ipf(8) (default /sbin/ipf).

     ipfilter_rules
		 (str) Set to /etc/ipf.rules by default.  This variable contains
		 the  name  of the filter rule definition file.  The file is ex-
		 pected to be readable for the ipf(8) command to execute.

     ipv6_ipfilter_rules
		 (str) Set to /etc/ipf6.rules by default.   This  variable  con-
		 tains	the  IPv6  filter rule definition file.  The file is ex-
		 pected to be readable for the ipf(8) command to execute.

     ipfilter_flags
		 (str) Empty by default.  This variable contains flags passed to
		 the ipf(8) program.

     ipnat_enable
		 (bool) Set to "NO" by default.  Set it to "YES" to  enable  ip-
		 nat(8)  network address translation.  See ipfilter_enable for a
		 detailed discussion.

     ipnat_program
		 (str) Path to ipnat(8) (default /sbin/ipnat).

     ipnat_rules
		 (str) Set to /etc/ipnat.rules by default.  This  variable  con-
		 tains the name of the file holding the network address transla-
		 tion  definition.  This file is expected to be readable for the
		 ipnat(8) command to execute.

     ipnat_flags
		 (str) Empty by default.  This variable contains flags passed to
		 the ipnat(8) program.

     ipmon_enable
		 (bool) Set to "NO" by default.  Set it to "YES" to  enable  ip-
		 mon(8)  monitoring  (logging ipf(8) and ipnat(8) events).  Set-
		 ting	this   variable   needs   setting   ipfilter_enable   or
		 ipnat_enable  too.   See ipfilter_enable for a detailed discus-
		 sion.

     ipmon_program
		 (str) Path to ipmon(8) (default /sbin/ipmon).

     ipmon_flags
		 (str) Set to "-Ds" by default.  This  variable  contains  flags
		 passed  to the ipmon(8) program.  Another typical example would
		 be "-D /var/log/ipflog" to have ipmon(8) log directly to a file
		 bypassing syslogd(8).	Make sure to adjust  /etc/newsyslog.conf
		 in such case like this:

		 /var/log/ipflog  640  10  100	*  Z  /var/run/ipmon.pid

     ipfs_enable
		 (bool)  Set  to  "NO"	by  default.   Set it to "YES" to enable
		 ipfs(8) saving the filter and NAT state tables during	shutdown
		 and reloading them during startup again.  Setting this variable
		 needs	setting  ipfilter_enable  or  ipnat_enable to "YES" too.
		 See ipfilter_enable for a detailed discussion.   Note	that  if
		 kern_securelevel  is  set  to 3, ipfs_enable cannot be used be-
		 cause the raised securelevel will prevent ipfs(8)  from  saving
		 the state tables at shutdown time.

     ipfs_program
		 (str) Path to ipfs(8) (default /sbin/ipfs).

     ipfs_flags  (str) Empty by default.  This variable contains flags passed to
		 the ipfs(8) program.

     pf_enable	 (bool)  Set  to "NO" by default.  Setting this to "YES" enables
		 pf(4) packet filtering.

		 Typical usage will require putting

		       pf_enable="YES"

		 into  /etc/rc.conf  and  editing  /etc/pf.conf   appropriately.
		 Adding

		       device pf

		 builds  support for pf(4) into the kernel, otherwise the kernel
		 module will be loaded.

     pf_rules	 (str)	Path  to  pf(4)  ruleset  configuration  file	(default
		 /etc/pf.conf).

     pf_program  (str) Path to pfctl(8) (default /sbin/pfctl).

     pf_flags	 (str)	If  pf_enable is set to "YES", these flags are passed to
		 the pfctl(8) program when loading the ruleset.

     pflog_enable
		 (bool) Set to "NO" by default.  Setting this to  "YES"  enables
		 pflogd(8) which logs packets from the pf(4) packet filter.

     pflog_logfile
		 (str)	If  pflog_enable  is  set  to  "YES" this controls where
		 pflogd(8) stores the logfile (default	/var/log/pflog).   Check
		 /etc/newsyslog.conf to adjust logfile rotation for this.

     pflog_program
		 (str) Path to pflogd(8) (default /sbin/pflogd).

     pflog_flags
		 (str)	Empty  by  default.   This  variable contains additional
		 flags passed to the pflogd(8) program.

     ftpproxy_enable
		 (bool) Set to "NO" by default.  Setting this to  "YES"  enables
		 ftp-proxy(8)  which  supports the pf(4) packet filter in trans-
		 lating ftp connections.

     ftpproxy_flags
		 (str) Empty by  default.   This  variable  contains  additional
		 flags passed to the ftp-proxy(8) program.

     pfsync_enable
		 (bool)  Set  to "NO" by default.  Setting this to "YES" enables
		 exposing pf(4) state changes to other hosts over the network by
		 means of pfsync(4).  The pfsync_syncdev variable must	also  be
		 set then.

     pfsync_syncdev
		 (str)	Empty  by  default.  This variable specifies the name of
		 the network interface pfsync(4)  should  operate  through.   It
		 must be set accordingly if pfsync_enable is set to "YES".

     pfsync_syncpeer
		 (str)	Empty  by  default.   This variable is optional.  By de-
		 fault, state change messages are sent out on  the  synchronisa-
		 tion  interface using IP multicast packets.  The protocol is IP
		 protocol  240,  PFSYNC,  and  the  multicast  group   used   is
		 224.0.0.240.	When  a  peer  address	is  specified  using the
		 pfsync_syncpeer option, the peer address is used as a	destina-
		 tion  for  the pfsync traffic, and the traffic can then be pro-
		 tected using ipsec(4).  See the pfsync(4) manpage for more  de-
		 tails about using ipsec(4) with pfsync(4) interfaces.

     pfsync_ifconfig
		 (str)	Empty  by default.  This variable can contain additional
		 options to be passed to the ifconfig(8) command used to set  up
		 pfsync(4).

     tcp_extensions
		 (bool)  Set to "YES" by default.  Setting this to "NO" disables
		 certain TCP options as described by RFC 1323.	Setting this  to
		 "NO"  might  help remedy such problems with connections as ran-
		 domly hanging or other weird behavior.   Some	network  devices
		 are known to be broken with respect to these options.

     log_in_vain
		 (int)	 Set   to   0  by  default.   The  sysctl(8)  variables,
		 net.inet.tcp.log_in_vain and net.inet.udp.log_in_vain,  as  de-
		 scribed in tcp(4) and udp(4), are set to the given value.

     tcp_keepalive
		 (bool)  Set  to "YES" by default.  Setting to "NO" will disable
		 probing idle TCP connections to verify that the peer  is  still
		 up and reachable.

     tcp_drop_synfin
		 (bool) Set to "NO" by default.  Setting to "YES" will cause the
		 kernel  to  ignore  TCP  frames  that have both the SYN and FIN
		 flags set.  This prevents OS fingerprinting, but may break some
		 legitimate applications.

     icmp_drop_redirect
		 (bool) Set to "NO" by default.  Setting to "YES" will cause the
		 kernel to ignore ICMP REDIRECT packets.  Refer to  icmp(4)  for
		 more information.

     icmp_log_redirect
		 (bool) Set to "NO" by default.  Setting to "YES" will cause the
		 kernel  to  log  ICMP REDIRECT packets.  Note that the log mes-
		 sages are not rate-limited, so this option should only be  used
		 for troubleshooting networks.	Refer to icmp(4) for more infor-
		 mation.

     icmp_bmcastecho
		 (bool)  Set  to "YES" to respond to broadcast or multicast ICMP
		 ping packets.	Refer to icmp(4) for more information.

     ip_portrange_first
		 (int) If not set to "NO", this is the first port in the default
		 portrange.  Refer to ip(4) for more information.

     ip_portrange_last
		 (int) If not set to "NO", this is the last port in the  default
		 portrange.  Refer to ip(4) for more information.

     network_interfaces
		 (str)	Set  to  the  list of network interfaces to configure on
		 this host or "AUTO" (the default) for all  current  interfaces.
		 Setting  the network_interfaces variable to anything other than
		 the default is deprecated.  Interfaces that  the  administrator
		 wishes to store configuration for, but not start at boot should
		 be    configured   with   the	 "NOAUTO"   keyword   in   their
		 ifconfig_<interface> variables as described below.

		 An ifconfig_<interface> variable is also assumed to  exist  for
		 each  value  of interface.  When an interface name contains any
		 of the characters ".-/+" they	are  translated  to  "_"  before
		 lookup.   The variable can contain arguments to ifconfig(8), as
		 well as  special  case-insensitive  keywords  described  below.
		 Such  keywords  are  removed before passing the value to ifcon-
		 fig(8) while the order of the other arguments is preserved.

		 One  can  configure  more  than  one  IPv4  address  with   the
		 ipv4_addrs_<interface> variable.  One or more IP addresses must
		 be  provided  in  Classless Inter-Domain Routing (CIDR) address
		 notation, whose last byte can be a range like	192.0.2.5-23/24.
		 In  this case the address 192.0.2.5 will be configured with the
		 netmask /24 and the addresses 192.0.2.6 to 192.0.2.23 with  the
		 non-conflicting  netmask  /32	as  explained in the ifconfig(8)
		 alias section.  With the interface in question  being	ed0,  an
		 example could look like:

		 ipv4_addrs_ed0="192.0.2.129/27 192.0.2.1-5/28"

		 It  is  also possible to add IP alias entries using ifconfig(8)
		 syntax with the "inet" keyword.  Assuming that the interface in
		 question was ed0, it might look something like this:

		 ifconfig_ed0_alias0="inet 127.0.0.253 netmask 0xffffffff"
		 ifconfig_ed0_alias1="inet 127.0.0.254 netmask 0xffffffff"

		 And so on.  For each ifconfig_<interface>_alias<n>  entry  with
		 the  "inet"  keyword  that is found, its contents are passed to
		 ifconfig(8).  Execution stops at the first unsuccessful access,
		 so if something like this is present:

		 ifconfig_ed0_alias0="inet 127.0.0.251 netmask 0xffffffff"
		 ifconfig_ed0_alias1="inet 127.0.0.252 netmask 0xffffffff"
		 ifconfig_ed0_alias2="inet 127.0.0.253 netmask 0xffffffff"
		 ifconfig_ed0_alias4="inet 127.0.0.254 netmask 0xffffffff"

		 Then note that alias4 would not be added since the search would
		 stop with the missing "alias3" entry.	Due to this difficult to
		 manage behavior, the ifconfig_<interface>_alias<n> form is dep-
		 recated.

		 If the /etc/start_if.<interface> file is present,  it	is  read
		 and  executed	by  the sh(1) interpreter before configuring the
		 interface  as	specified  in	the   ifconfig_<interface>   and
		 ifconfig_<interface>_alias<n> variables.

		 If  a	vlans_<interface>  variable  is set, a vlan(4) interface
		 will be created for each item in the list with the vlandev  ar-
		 gument  set to interface.  If a vlan interface's name is a num-
		 ber, then that number is used as the vlan tag and the new  vlan
		 interface is named interface.tag.  Otherwise, the vlan tag must
		 be	specified     via    a	  vlan	  parameter    in    the
		 create_args_<interface> variable.

		 To create a vlan device named em0.101 on em0 with the vlan  tag
		 101 and the optional the IPv4 address 192.0.2.1/24:

		 vlans_em0="101"
		 ifconfig_em0_101="inet 192.0.2.1/24"

		 To  create  a vlan device named myvlan on em0 with the vlan tag
		 102:

		 vlans_em0="myvlan"
		 create_args_myvlan="vlan 102"

		 If a wlans_<interface> variable is set,  an  wlan(4)  interface
		 will  be created for each item in the list with the wlandev ar-
		 gument set to interface.  Further wlan cloning arguments may be
		 passed  to  the  ifconfig(8)  create  command	by  setting  the
		 create_args_<interface>  variable.  One or more wlan(4) devices
		 must be created for each wireless devices as  of  FreeBSD  8.0.
		 Debugging  flags for wlan(4) devices as set by wlandebug(8) may
		 be specified with an wlandebug_<interface> variable.  The  con-
		 tents of this variable will be passed directly to wlandebug(8).

		 If  the ifconfig_<interface> contains the keyword "NOAUTO" then
		 the  interface  will  not  be	configured   at   boot	 or   by
		 /etc/pccard_ether when network_interfaces is set to "AUTO".

		 It  is  possible  to  bring up an interface with DHCP by adding
		 "DHCP" to the ifconfig_<interface> variable.  For instance,  to
		 initialize the ed0 device via DHCP, it is possible to use some-
		 thing like:

		 ifconfig_ed0="DHCP"

		 Also,	if  you  want  to configure your wireless interface with
		 wpa_supplicant(8) for use with WPA, EAP/LEAP or WEP,  you  need
		 to add "WPA" to the ifconfig_<interface> variable.

		 Finally,  you	can add ifconfig(8) options in this variable, in
		 addition to the /etc/start_if.<interface> file.  For  instance,
		 to  configure an ath(4) wireless device in station mode with an
		 address obtained via DHCP, using WPA authentication and 802.11b
		 mode, it is possible to use something like:

		 wlans_ath0="wlan0"
		 ifconfig_wlan0="DHCP WPA mode 11b"

		 In addition to the ifconfig_<interface> form, a fallback  vari-
		 able  ifconfig_DEFAULT  may be configured.  It will be used for
		 all interfaces with no ifconfig_<interface> variable.	This  is
		 intended  to  replace	the  no longer supported pccard_ifconfig
		 variable.

		 It is also possible to rename an interface by doing:

		 ifconfig_ed0_name="net0"
		 ifconfig_net0="inet 192.0.2.1 netmask 0xffffff00"

     ipv6_enable
		 This variable is deprecated.  Use ifconfig_<interface>_ipv6 and
		 ipv6_activate_all_interfaces if necessary.

		 (bool) If the variable is "YES", "inet6 accept_rtadv" is  added
		 to	all	of     ifconfig_<interface>_ipv6     and     the
		 ipv6_activate_all_interfaces is defined as "YES".

     ipv6_prefer
		 This variable is deprecated.  Use ip6addrctl_policy instead.

		 (bool) If the variable is "YES", the default address  selection
		 policy table set by ip6addrctl(8) will be IPv6-preferred.

		 If  the  variable is "NO", the default address selection policy
		 table set by ip6addrctl(8) will be IPv4-preferred.

     ipv6_activate_all_interfaces
		 (bool) This controls initial configuration on IPv6-capable  in-
		 terfaces  with no corresponding ifconfig_<interface>_ipv6 vari-
		 able.	Note that it is not always necessary to set  this  vari-
		 able  to  "YES"  to use IPv6 functionality on FreeBSD.  In most
		 cases,  just  configuring  ifconfig_<interface>_ipv6  variables
		 works.

		 If  the  variable  is	"NO", all interfaces which do not have a
		 corresponding ifconfig_<interface>_ipv6 variable will be marked
		 as "IFDISABLED" at creation.  This means that all of IPv6 func-
		 tionality on that interface is completely disabled to enforce a
		 security policy.  If the variable is set  to  "YES",  the  flag
		 will be cleared on all of the interfaces.

		 In  most  cases, just defining an ifconfig_<interface>_ipv6 for
		 an IPv6-capable interface should be sufficient.  However, if an
		 interface is added dynamically  (by  some  tunneling  protocols
		 such  as PPP, for example), it is often difficult to define the
		 variable  in  advance.   In  such  a  case,   configuring   the
		 "IFDISABLED"  flag  can be disabled by setting this variable to
		 "YES".

		 For more details of the "IFDISABLED" flag and	keywords  "inet6
		 ifdisabled", see ifconfig(8).

		 Default is "NO".

     ipv6_privacy
		 (bool)  If the variable is "YES" privacy addresses will be gen-
		 erated for each IPv6 interface as described in RFC 4941.

     ipv6_network_interfaces
		 (str) This is the IPv6 equivalent of network_interfaces.   Nor-
		 mally manual configuration of this variable is not needed.

     ipv6_cpe_wanif
		 (str)	If  the variable is set to an interface name, the ifcon-
		 fig(8) options "inet6 -no_radr accept_rtadv" will be  added  to
		 the   specified   interface   automatically  before  evaluating
		 ifconfig_<interface>_ipv6,   and   two   sysctl(8)    variables
		 net.inet6.ip6.rfc6204w3  and  net.inet6.ip6.no_radr will be set
		 to 1.

		 This means the specified interface will  accept  ICMPv6  Router
		 Advertisement	messages  on  that  link  and add the discovered
		 routers into the Default Router List.	While the  other  inter-
		 faces	can still accept RA messages if the "inet6 accept_rtadv"
		 option is specified, adding routes into the Default Router List
		 will be disabled by "inet6 no_radr" option by default.  See if-
		 config(8) for more details.

		 Note that ICMPv6 Router Advertisement messages will be accepted
		 even when net.inet6.ip6.forwarding is 1  (packet  fowarding  is
		 enabled) when net.inet6.ip6.rfc6204w3 is set to 1.

		 Default is "NO".

     ifconfig_<interface>_ipv6
		 (str)	IPv6  functionality on an interface should be configured
		 by ifconfig_<interface>_ipv6, instead of setting ifconfig para-
		 meters in ifconfig_<interface>.  If this variable is empty, all
		 of IPv6 configurations on  the  specified  interface  by  other
		 variables such as ipv6_prefix_<interface> will be ignored.

		 Aliases  should  be  set  by ifconfig_<interface>_alias<n> with
		 "inet6" keyword.  For example:

		 ifconfig_ed0_ipv6="inet6 2001:db8:1::1 prefixlen 64"
		 ifconfig_ed0_alias0="inet6 2001:db8:2::1 prefixlen 64"

		 Interfaces  that  have  an  "inet6  accept_rtadv"  keyword   in
		 ifconfig_<interface>_ipv6 setting will be automatically config-
		 ured  by  SLAAC (StateLess Address AutoConfiguration) described
		 in RFC 4862.

		 Note that a link-local address will be automatically configured
		 in addition to the configured	global-scope  addresses  because
		 the  IPv6  specifications require it on each link.  The address
		 is calculated from the MAC address by using  an  algorithm  de-
		 fined in RFC 4862, Section 5.3.

		 If  only  a  link-local address is needed on the interface, the
		 following configuration can be used:

		 ifconfig_ed0_ipv6="inet6 auto_linklocal"

		 A link-local address can also be configured manually.	This  is
		 useful for the default router address of an IPv6 router so that
		 it does not change when the network interface card is replaced.
		 For example:

		 ifconfig_ed0_ipv6="inet6 fe80::1 prefixlen 64"

     ipv6_prefix_<interface>
		 (str)	  If	one    or   more   prefixes   are   defined   in
		 ipv6_prefix_<interface> addresses based on each prefix and  the
		 EUI-64  interface  index  will be configured on that interface.
		 Note	that   this    variable    will    be	 ignored    when
		 ifconfig_<interface>_ipv6 is empty.

		 For example, the following configuration

		 ipv6_prefix_ed0="2001:db8:1:0 2001:db8:2:0"

		 is equivalent to the following:

		 ifconfig_ed0_alias0="inet6 2001:db8:1:: eui64 prefixlen 64"
		 ifconfig_ed0_alias1="inet6 2001:db8:1:: prefixlen 64 anycast"
		 ifconfig_ed0_alias2="inet6 2001:db8:2:: eui64 prefixlen 64"
		 ifconfig_ed0_alias3="inet6 2001:db8:2:: prefixlen 64 anycast"

		 These	Subnet-Router  anycast addresses will be added only when
		 ipv6_gateway_enable is YES.

     ipv6_default_interface
		 (str) If not set to "NO", this is the default output  interface
		 for  scoped  addresses.   This works only with ipv6_gateway_en-
		 able="NO".

     ip6addrctl_enable
		 (bool) This variable is to enable configuring	default  address
		 selection  policy table (RFC 3484).  The table can be specified
		 in another variable ip6addrctl_policy.   For  ip6addrctl_policy
		 the   following   keywords  can  be  specified:  "ipv4_prefer",
		 "ipv6_prefer", or "AUTO".

		 If "ipv4_prefer" or "ipv6_prefer" is  specified,  ip6addrctl(8)
		 installs  a  pre-defined  policy table described in Section 2.1
		 (IPv6-preferred) or 10.3 (IPv4-preferred) of RFC 3484.

		 If  "AUTO"  is  specified,  it  attempts   to	 read	a   file
		 /etc/ip6addrctl.conf  first.	If  this  file	is found, ip6ad-
		 drctl(8) reads and installs it.  If not found, a policy is  au-
		 tomatically set according to ipv6_activate_all_interfaces vari-
		 able; if the variable is set to "YES" the IPv6-preferred one is
		 used.	Otherwise IPv4-preferred.

		 The  default  value  of ip6addrctl_enable and ip6addrctl_policy
		 are "YES" and "AUTO", respectively.

     cloned_interfaces
		 (str) Set to the list of clonable network interfaces to  create
		 on  this  host.  Further cloning arguments may be passed to the
		 ifconfig(8) create command for each interface	by  setting  the
		 create_args_<interface> variable.  Entries in cloned_interfaces
		 are automatically appended to network_interfaces for configura-
		 tion.

     fec_interfaces
		 (str) Set to the list of ng_fec(4) Fast EtherChannel interfaces
		 to configure on this host.  A fecconfig_<interface> variable is
		 assumed  to  exist  for  each value of interface.  The value of
		 this variable is used to configure link  aggregated  interfaces
		 according  to	the  syntax of the NGM_FEC_ADD_IFACE to ngctl(8)
		 msg.  Additionally, this option ensures that each listed inter-
		 face is created via the mkpeer command to ngctl(8)  before  at-
		 tempting to configure it.  For example:

		 fec_interfaces="fec0"
		 fecconfig_fec0="em0 em1"
		 ifconfig_fec0="DHCP"

     gif_interfaces
		 (str)	Set to the list of gif(4) tunnel interfaces to configure
		 on this host.	A gifconfig_<interface> variable is  assumed  to
		 exist	for each value of interface.  The value of this variable
		 is used to configure the link layer of the tunnel according  to
		 the  syntax of the tunnel option to ifconfig(8).  Additionally,
		 this option ensures that each listed interface is  created  via
		 the create option to ifconfig(8) before attempting to configure
		 it.

     sppp_interfaces
		 (str)	Set  to  the  list of sppp(4) interfaces to configure on
		 this host.  A spppconfig_<interface> variable is assumed to ex-
		 ist for each value of interface.  Each interface should also be
		 configured by a general ifconfig_<interface> setting.	Refer to
		 spppcontrol(8) for more information about available options.

     ppp_enable  (bool) If set to "YES", run the ppp(8) daemon.

     ppp_profile
		 (str) The name of the profile to  use	from  /etc/ppp/ppp.conf.
		 Also  used  for  per-profile overrides of ppp_mode and ppp_nat,
		 and ppp_<profile>_unit.  When the profile name contains any  of
		 the  characters  ".-/+" they are translated to "_" for the pro-
		 poses of the override variable names.

     ppp_mode	 (str) Mode in which to run the ppp(8) daemon.

     ppp_<profile>_mode
		 (str) Overrides the  global  ppp_mode	for  profile.	Accepted
		 modes	are  "auto", "ddial", "direct" and "dedicated".  See the
		 manual for a full description.

     ppp_nat	 (bool) If set to "YES", enables  network  address  translation.
		 Used in conjunction with gateway_enable allows hosts on private
		 network  addresses  access to the Internet using this host as a
		 network address translating router.

     ppp_<profile>_nat
		 (str) Overrides the global ppp_nat for profile.

     ppp_<profile>_unit
		 (int) Set the unit number to be used for this profile.  See the
		 manual description of -unitN for details.

     ppp_user	 (str) The name  of  the  user	under  which  ppp(8)  should  be
		 started.  By default, ppp(8) is started as "root".

     rc_conf_files
		 (str)	This option is used to specify a list of files that will
		 override the settings in /etc/defaults/rc.conf.  The files will
		 be read in the order in which they are specified and should in-
		 clude the full path to the file.  By default, the files  speci-
		 fied are /etc/rc.conf and /etc/rc.conf.local

     zfs_enable  (bool) If set to "YES", /etc/rc.d/zfs will attempt to automati-
		 cally	mount  ZFS  file  systems  and	initialize  ZFS  volumes
		 (ZVOLs).

     gptboot_enable
		 (bool) If set to "YES", /etc/rc.d/gptboot will log if the  sys-
		 tem  successfully  (or  not) booted from a GPT partition, which
		 had the bootonce attribute set using gpart(8) utility.

     gbde_autoattach_all
		 (bool) If set to "YES", /etc/rc.d/gbde will attempt to automat-
		 ically initialize your .bde devices in /etc/fstab.

     gbde_devices
		 (str) List the devices that the script should try to attach, or
		 "AUTO".

     gbde_lockdir
		 (str) The directory where the gbde(4)	lockfiles  are	located.
		 The default lockfile directory is /etc.

		 The lockfile for each individual gbde(4) device can be overrid-
		 den by setting the variable gbde_lock_<device>, where device is
		 the encrypted device without the "/dev/" and ".bde" parts.

     gbde_attach_attempts
		 (int) Number of times to attempt attaching to a gbde(4) device,
		 i.e.,	how  many  times  the user is asked for the pass-phrase.
		 Default is 3.

     geli_devices
		 (str) List of devices to automatically attach	on  boot.   Note
		 that .eli devices from /etc/fstab are automatically appended to
		 this list.

     geli_tries  (int)	Number	of  times user is asked for the pass-phrase.  If
		 empty, it will be taken from kern.geom.eli.tries  sysctl  vari-
		 able.

     geli_default_flags
		 (str) Default flags to use by geli(8) when configuring disk en-
		 cryption.   Flags can be configured for every device separately
		 by defining geli_<device>_flags variable.

     geli_autodetach
		 (str) Specifies if GELI devices should be marked for detach  on
		 last  close  after file systems are mounted.  Default is "YES".
		 This can be changed for every	device	separately  by	defining
		 geli_<device>_autodetach variable.

     geli_swap_flags
		 Options  passed  to  the  geli(8)  utility  when encrypted GEOM
		 providers for swap partitions are created.  The default is  "-e
		 aes -l 256 -s 4096 -d".

     root_rw_mount
		 (bool)  Set  to  "YES"  by default.  After the file systems are
		 checked at boot time, the root  file  system  is  remounted  as
		 read-write  if  this  is  set	to "YES".  Diskless systems that
		 mount their root file system from a read-only remote NFS  share
		 should set this to "NO" in their rc.conf.

     fsck_y_enable
		 (bool) If set to "YES", fsck(8) will be run with the -y flag if
		 the initial preen of the file systems fails.

     background_fsck
		 (bool)  If set to "YES", the system will attempt to run fsck(8)
		 in the background where possible.

     background_fsck_delay
		 (int) The amount of time in seconds to sleep before starting  a
		 background  fsck(8).	It  defaults  to  sixty seconds to allow
		 large applications such as the X server to  start  before  disk
		 I/O  bandwidth is monopolized by fsck(8).  If set to a negative
		 number, the background file system check will be delayed indef-
		 initely to allow the administrator to run it at a  more  conve-
		 nient time.  For example it may be run from cron(8) by adding a
		 line like

		       0 4 * * * root /etc/rc.d/bgfsck forcestart

		 to /etc/crontab.

     netfs_types
		 (str)	List  of file system types that are network-based.  This
		 list should generally	not  be  modified  by  end  users.   Use
		 extra_netfs_types instead.

     extra_netfs_types
		 (str)	If  set to something other than "NO" (the default), this
		 variable extends the list of file system types for which  auto-
		 matic	mounting at startup by rc(8) should be delayed until the
		 network is initialized.  It should contain  a	whitespace-sepa-
		 rated	list  of network file system descriptor pairs, each con-
		 sisting of a file system type as passed to mount(8) and  a  hu-
		 man-readable,	one-word description, joined with a colon (`:').
		 Extending the default list in this way is only  necessary  when
		 third party file system types are used.

     syslogd_enable
		 (bool) If set to "YES", run the syslogd(8) daemon.

     syslogd_program
		 (str) Path to syslogd(8) (default /usr/sbin/syslogd).

     syslogd_flags
		 (str) If syslogd_enable is set to "YES", these are the flags to
		 pass to syslogd(8).

     inetd_enable
		 (bool) If set to "YES", run the inetd(8) daemon.

     inetd_program
		 (str) Path to inetd(8) (default /usr/sbin/inetd).

     inetd_flags
		 (str)	If  inetd_enable is set to "YES", these are the flags to
		 pass to inetd(8).

     hastd_enable
		 (bool) If set to "YES", run the hastd(8) daemon.

     hastd_program
		 (str) Path to hastd(8) (default /sbin/hastd).

     hastd_flags
		 (str) If hastd_enable is set to "YES", these are the  flags  to
		 pass to hastd(8).

     named_enable
		 (bool) If set to "YES", run the named(8) daemon.

     named_program
		 (str) Path to named(8) (default /usr/sbin/named).

     named_conf  (str)	 Path	to   named(8)	configuration	file,	(default
		 /etc/namedb/named.conf).

     named_flags
		 (str) If named_enable is set to "YES", these are the  flags  to
		 pass to named(8).

     named_uid	 (str) The user that the named(8) process should be run as.

     named_chrootdir
		 (str)	The  root directory for a name server run in a chroot(8)
		 environment (default /var/named).  If left empty named(8)  will
		 not be run in a chroot(8) environment.

     named_chroot_autoupdate
		 (bool) Set to "NO" to disable automatic update of the chroot(8)
		 environment.

     named_symlink_enable
		 (bool)  Set  to "NO" to disable symlinking of daemon's PID file
		 into the chroot(8) environment.

     named_wait  (bool) Set to have /etc/rc.d/named loop until working name ser-
		 vice is established.

     named_wait_host
		 (str) Name of host to lookup for the named_wait  option.   (De-
		 fault localhost)

     named_auto_forward
		 (bool) Set to enable automatic creation of a forwarder configu-
		 ration file derived from /etc/resolv.conf.

     named_auto_forward_only
		 (bool)  Set  to change the default forwarder configuration from
		 "forward first" to "forward only".

     kerberos5_server_enable
		 (bool) Set to "YES" to start a Kerberos 5 authentication server
		 at boot time.

     kerberos5_server
		 (str) If kerberos5_server_enable is set to "YES"  this  is  the
		 path to Kerberos 5 Authentication Server.

     kerberos5_server_flags
		 (str)	Empty  by  default.   This  variable contains additional
		 flags to be passed to the Kerberos 5 authentication server.

     kadmind5_server_enable
		 (bool) Set to "YES" to start kadmind(8), the Kerberos 5  Admin-
		 istration Daemon; set to "NO" on a slave server.

     kadmind5_server
		 (str)	If  kadmind5_server_enable  is	set to "YES" this is the
		 path to Kerberos 5 Administration Daemon.

     kpasswdd_server_enable
		 (bool) Set to "YES" to start kpasswdd(8), the Kerberos 5  Pass-
		 word-Changing Daemon; set to "NO" on a slave server.

     kpasswdd_server
		 (str)	If  kpasswdd_server_enable  is	set to "YES" this is the
		 path to Kerberos 5 Password-Changing Daemon.

     rwhod_enable
		 (bool) If set to "YES", run the rwhod(8) daemon at boot time.

     rwhod_flags
		 (str) If rwhod_enable is set to "YES", these are the  flags  to
		 pass to it.

     amd_enable  (bool) If set to "YES", run the amd(8) daemon at boot time.

     amd_flags	 (str)	If  amd_enable	is  set to "YES", these are the flags to
		 pass to it.  See the amd(8) manpage for more information.

     amd_map_program
		 (str) If set, the specified program is run to get the	list  of
		 amd(8)  maps.	 For  example,	if the amd(8) maps are stored in
		 NIS, one can set this to run ypcat(1) to get a list  of  amd(8)
		 maps from the amd.master NIS map.

     update_motd
		 (bool)  If set to "YES", /etc/motd will be updated at boot time
		 to reflect the kernel release	being  run.   If  set  to  "NO",
		 /etc/motd will not be updated.

     nfs_client_enable
		 (bool)  If  set  to  "YES",  run the NFS client daemons at boot
		 time.

     nfs_access_cache
		 (int) If nfs_client_enable is set to "YES", this can be set  to
		 "0" to disable NFS ACCESS RPC caching, or to the number of sec-
		 onds for which NFS ACCESS results should be cached.  A value of
		 2-10 seconds will substantially reduce network traffic for many
		 NFS operations.

     nfs_server_enable
		 (bool)  If  set  to  "YES",  run the NFS server daemons at boot
		 time.

     nfs_server_flags
		 (str) If nfs_server_enable is set to "YES", these are the flags
		 to pass to the nfsd(8) daemon.

     nfsv4_server_enable
		 (bool)   If   nfs_server_enable   is	set   to    "YES"    and
		 nfsv4_server_enable  are  set	to  "YES", enable the server for
		 NFSv4 as well as NFSv2 and NFSv3.

     nfsuserd_enable
		 (bool) If nfsuserd_enable is set to  "YES",  run  the	nfsuserd
		 daemon,  which  is  needed  for  NFSv4  in order to map between
		 user/group names vs uid/gid numbers.  If nfsv4_server_enable is
		 set to "YES", this will be forced enabled.

     nfsuserd_flags
		 (str) If nfsuserd_enable is set to "YES", these are  the  flags
		 to pass to the nfsuserd(8) daemon.

     nfscbd_enable
		 (bool) If nfscbd_enable is set to "YES", run the nfscbd daemon,
		 which enables callbacks/delegations for the NFSv4 client.

     nfscbd_flags
		 (str)	If nfscbd_enable is set to "YES", these are the flags to
		 pass to the nfscbd(8) daemon.

     oldnfs_server_enable
		 (bool) If oldnfs_server_enable is set to "YES", force	the  NFS
		 server  daemons  to  run  the old NFS server code that does not
		 support NFSv4.

     mountd_enable
		 (bool) If set to "YES", and no nfs_server_enable is set,  start
		 mountd(8),  but  not  nfsd(8) daemon.	It is commonly needed to
		 run CFS without real NFS used.

     mountd_flags
		 (str) If mountd_enable is set to "YES", these are the flags  to
		 pass to the mountd(8) daemon.

     weak_mountd_authentication
		 (bool) If set to "YES", allow services like PCNFSD to make non-
		 privileged mount requests.

     nfs_reserved_port_only
		 (bool)  If  set to "YES", provide NFS services only on a secure
		 port.

     nfs_bufpackets
		 (int) If set to a number, indicates the number of packets worth
		 of socket buffer space to reserve on an NFS client.  The kernel
		 default is typically 4.  Using a higher number may be useful on
		 gigabit networks to improve performance.  The minimum value  is
		 2 and the maximum is 64.

     rpc_lockd_enable
		 (bool)  If  set  to "YES" and also an NFS server or client, run
		 rpc.lockd(8) at boot time.

     rpc_lockd_flags
		 (str) If rpc_lockd_enable is set to "YES", these are the  flags
		 to pass to the rpc.lockd(8) daemon.

     rpc_statd_enable
		 (bool)  If  set  to "YES" and also an NFS server or client, run
		 rpc.statd(8) at boot time.

     rpc_statd_flags
		 (str) If rpc_statd_enable is set to "YES", these are the  flags
		 to pass to the rpc.statd(8) daemon.

     rpcbind_program
		 (str) Path to rpcbind(8) (default /usr/sbin/rpcbind).

     rpcbind_enable
		 (bool)  If  set  to  "YES",  run the rpcbind(8) service at boot
		 time.

     rpcbind_flags
		 (str) If rpcbind_enable is set to "YES", these are the flags to
		 pass to the rpcbind(8) daemon.

     keyserv_enable
		 (bool) If set to "YES", run the keyserv(8) daemon on  boot  for
		 running Secure RPC.

     keyserv_flags
		 (str) If keyserv_enable is set to "YES", these are the flags to
		 pass to keyserv(8) daemon.

     pppoed_enable
		 (bool)  If  set to "YES", run the pppoed(8) daemon at boot time
		 to provide PPP over Ethernet services.

     pppoed_<provider>
		 (str) pppoed(8) listens to requests to this provider and  ulti-
		 mately runs ppp(8) with a system argument of the same name.

     pppoed_flags
		 (str) Additional flags to pass to pppoed(8).

     pppoed_interface
		 (str)	The  network  interface  to  run  pppoed(8) on.  This is
		 mandatory when pppoed_enable is set to "YES".

     timed_enable
		 (bool) If set to "YES", run the timed(8) service at boot  time.
		 This  command is intended for networks of machines where a con-
		 sistent "network time" for all hosts must be established.  This
		 is often useful in large NFS environments where time stamps  on
		 files are expected to be consistent network-wide.

     timed_flags
		 (str)	If  timed_enable is set to "YES", these are the flags to
		 pass to the timed(8) service.

     ntpdate_enable
		 (bool) If set to "YES", run ntpdate(8) at system startup.  This
		 command is intended to synchronize the system clock  only  once
		 from  some  standard  reference.  An option to set this up ini-
		 tially (from a list of known servers) is also provided  by  the
		 sysinstall(8) program when the system is first installed.

     ntpdate_config
		 (str)	  Configuration    file    for	  ntpdate(8).	 Default
		 /etc/ntp.conf.

     ntpdate_hosts
		 (str) A whitespace-separated list of NTP servers to synchronize
		 with at startup.  The default is to use the servers  listed  in
		 ntpdate_config, if that file exists.

     ntpdate_program
		 (str) Path to ntpdate(8) (default /usr/sbin/ntpdate).

     ntpdate_flags
		 (str) If ntpdate_enable is set to "YES", these are the flags to
		 pass to the ntpdate(8) command (typically a hostname).

     ntpd_enable
		 (bool) If set to "YES", run the ntpd(8) command at boot time.

     ntpd_program
		 (str) Path to ntpd(8) (default /usr/sbin/ntpd).

     ntpd_config
		 (str)	  Path	 to   ntpd(8)	configuration	file.	 Default
		 /etc/ntp.conf.

     ntpd_flags  (str) If ntpd_enable is set to "YES", these are  the  flags  to
		 pass to the ntpd(8) daemon.

     ntpd_sync_on_start
		 (bool)  If set to "YES", ntpd(8) is run with the -g flag, which
		 syncs the system's clock on startup.  See ntpd(8) for more  in-
		 formation  regarding the -g option.  This is a preferred alter-
		 native to using ntpdate(8)  or  specifying  the  ntpdate_enable
		 variable.

     nis_client_enable
		 (bool)  If  set  to  "YES", run the ypbind(8) service at system
		 boot time.

     nis_client_flags
		 (str) If nis_client_enable is set to "YES", these are the flags
		 to pass to the ypbind(8) service.

     nis_ypset_enable
		 (bool) If set to "YES", run the ypset(8) daemon at system  boot
		 time.

     nis_ypset_flags
		 (str)	If nis_ypset_enable is set to "YES", these are the flags
		 to pass to the ypset(8) daemon.

     nis_server_enable
		 (bool) If set to "YES", run the ypserv(8) daemon at system boot
		 time.

     nis_server_flags
		 (str) If nis_server_enable is set to "YES", these are the flags
		 to pass to the ypserv(8) daemon.

     nis_ypxfrd_enable
		 (bool) If set to "YES", run the rpc.ypxfrd(8) daemon at  system
		 boot time.

     nis_ypxfrd_flags
		 (str) If nis_ypxfrd_enable is set to "YES", these are the flags
		 to pass to the rpc.ypxfrd(8) daemon.

     nis_yppasswdd_enable
		 (bool) If set to "YES", run the rpc.yppasswdd(8) daemon at sys-
		 tem boot time.

     nis_yppasswdd_flags
		 (str)	If  nis_yppasswdd_enable  is set to "YES", these are the
		 flags to pass to the rpc.yppasswdd(8) daemon.

     rpc_ypupdated_enable
		 (bool) If set to "YES", run the rpc.ypupdated daemon at  system
		 boot time.

     bsnmpd_enable
		 (bool) If set to "YES", run the bsnmpd(1) daemon at system boot
		 time.	 Be sure to understand the security implications of run-
		 ning SNMP daemon on your host.

     bsnmpd_flags
		 (str) If bsnmpd_enable is set to "YES", these are the flags  to
		 pass to the bsnmpd(1) daemon.

     defaultrouter
		 (str)	If  not set to "NO", create a default route to this host
		 name or IP address (use an IP address if this	router	is  also
		 required to get to the name server!).

     ipv6_defaultrouter
		 (str) The IPv6 equivalent of defaultrouter.

     static_arp_pairs
		 (str)	Set to the list of static ARP pairs that are to be added
		 at system boot time.  For each whitespace separated element  in
		 the  value, a static_arp_<element> variable is assumed to exist
		 whose contents will later be passed to a  "arp  -S"  operation.
		 For example

		 static_arp_pairs="gw"
		 static_arp_gw="192.168.1.1 00:01:02:03:04:05"

     static_ndp_pairs
		 (str)	Set to the list of static NDP pairs that are to be added
		 at system boot time.  For each whitespace separated element  in
		 the  value, a static_ndp_<element> variable is assumed to exist
		 whose contents will later be passed to a  "ndp  -s"  operation.
		 For example

		 static_ndp_pairs="gw"
		 static_ndp_gw="2001:db8:3::1 00:01:02:03:04:05"

     static_routes
		 (str)	Set to the list of static routes that are to be added at
		 system boot time.  If not set to "NO" then for each  whitespace
		 separated  element  in the value, a route_<element> variable is
		 assumed to exist whose contents  will	later  be  passed  to  a
		 "route add" operation.  For example:

		 static_routes="mcast gif0local"
		 route_mcast="-net 224.0.0.0/4 -iface gif0"
		 route_gif0local="-host 169.254.1.1 -iface lo0"

     ipv6_static_routes
		 (str) The IPv6 equivalent of static_routes.  If not set to "NO"
		 then  for  each  whitespace  separated  element in the value, a
		 ipv6_route_<element> variable is assumed to  exist  whose  con-
		 tents will later be passed to a "route add -inet6" operation.

     natm_static_routes
		 (str)	The natmip(4) equivalent of static_routes.  If not empty
		 then for each whitespace separated  element  in  the  value,  a
		 route_<element>  variable  is	assumed  to exist whose contents
		 will later be passed to a "atmconfig natm add" operation.

     gateway_enable
		 (bool) If set to "YES", configure host to act as an IP  router,
		 e.g. to forward packets between interfaces.

     ipv6_gateway_enable
		 (bool) The IPv6 equivalent of gateway_enable.

     routed_enable
		 (bool)  If  set  to  "YES",  run a routing daemon of some sort,
		 based on the settings of routed_program and routed_flags.

     route6d_enable
		 (bool) The IPv6 equivalent of routed_enable.  If set to  "YES",
		 run  a  routing  daemon  of some sort, based on the settings of
		 route6d_program and route6d_flags.

     routed_program
		 (str) If routed_enable is set to "YES", this is the name of the
		 routing daemon to use.

     route6d_program
		 (str) The IPv6 equivalent of routed_program.

     routed_flags
		 (str) If routed_enable is set to "YES", these are the flags  to
		 pass to the routing daemon.

     route6d_flags
		 (str) The IPv6 equivalent of routed_flags.

     mrouted_enable
		 (bool)  If  set  to  "YES",  run  the multicast routing daemon,
		 mrouted(8).

     mroute6d_enable
		 (bool) The IPv6 equivalent of mrouted_enable.	If set to "YES",
		 run the IPv6 multicast routing daemon.

		 Note that multicast routing daemons are no longer  included  in
		 the FreeBSD base system, however, both mrouted(8) and pim6dd(8)
		 may be installed from the FreeBSD Ports Collection.

     mrouted_flags
		 (str) If mrouted_enable is set to "YES", these are the flags to
		 pass to the mrouted(8) daemon.

     mroute6d_flags
		 (str) The IPv6 equivalent of mrouted_flags.  If mroute6d_enable
		 is  set to "YES", these are the flags passed to the IPv6 multi-
		 cast routing daemon.

     mroute6d_program
		 (str) If mroute6d_enable is set to "YES", this is the	path  to
		 the IPv6 multicast routing daemon.

     rtadvd_enable
		 (bool)  If set to "YES", run the rtadvd(8) daemon at boot time.
		 The rtadvd(8) utility sends ICMPv6  Router  Advertisement  mes-
		 sages	to  the interfaces specified in rtadvd_interfaces.  This
		 should only be enabled with great care.  You may want to  fine-
		 tune rtadvd.conf(5).

     rtadvd_interfaces
		 (str)	If rtadvd_enable is set to "YES" this is the list of in-
		 terfaces to use.

     ipxgateway_enable
		 (bool) If set to "YES", enable the routing of IPX traffic.

     ipxrouted_enable
		 (bool) If set to "YES", run the IPXrouted(8) daemon  at  system
		 boot time.

     ipxrouted_flags
		 (str)	If ipxrouted_enable is set to "YES", these are the flags
		 to pass to the IPXrouted(8) daemon.

     arpproxy_all
		 (bool) If set to "YES", enable global proxy ARP.

     forward_sourceroute
		 (bool) If set to "YES" and gateway_enable is also set to "YES",
		 source-routed packets are forwarded.

     accept_sourceroute
		 (bool) If set to "YES", the system  will  accept  source-routed
		 packets directed at it.

     rarpd_enable
		 (bool)  If set to "YES", run the rarpd(8) daemon at system boot
		 time.

     rarpd_flags
		 (str) If rarpd_enable is set to "YES", these are the  flags  to
		 pass to the rarpd(8) daemon.

     bootparamd_enable
		 (bool)  If set to "YES", run the bootparamd(8) daemon at system
		 boot time.

     bootparamd_flags
		 (str) If bootparamd_enable is set to "YES", these are the flags
		 to pass to the bootparamd(8) daemon.

     stf_interface_ipv4addr
		 (str) If not set to "NO", this is the local  IPv4  address  for
		 6to4  (IPv6 over IPv4 tunneling interface).  Specify this entry
		 to enable the 6to4 interface.

     stf_interface_ipv4plen
		 (int) Prefix length for 6to4 IPv4 addresses, to limit peer  ad-
		 dress range.  An effective value is 0-31.

     stf_interface_ipv6_ifid
		 (str) IPv6 interface ID for stf(4).  This can be set to "AUTO".

     stf_interface_ipv6_slaid
		 (str) IPv6 Site Level Aggregator for stf(4).

     ipv6_faith_prefix
		 (str)	If not set to "NO", this is the faith prefix to enable a
		 FAITH IPv6-to-IPv4 TCP translator.   You  also  need  faithd(8)
		 setup.

     ipv6_ipv4mapping
		 (bool)  If  set  to "YES" this enables IPv4 mapped IPv6 address
		 communication (like ::ffff:a.b.c.d).

     atm_enable  (bool) Set to "YES" to enable the configuration of  ATM  inter-
		 faces	at  system  boot time.	For all of the ATM variables de-
		 scribed below, please refer to the atm(8) manual page for  fur-
		 ther  details	on the available command parameters.  Also refer
		 to the files in /usr/share/examples/atm for more detailed  con-
		 figuration information.

     atm_load	 (str) This is a list of physical ATM interface drivers to load.
		 Typical values are "hfa_pci" and/or "hea_pci".

     atm_netif_<intf>
		 (str)	For  the  ATM physical interface intf, this variable de-
		 fines the name prefix and count for the ATM network  interfaces
		 to  be  created.  The value will be passed as the parameters of
		 an "atm set netif intf" command.

     atm_sigmgr_<intf>
		 (str) For the ATM physical interface intf,  this  variable  de-
		 fines the ATM signalling manager to be used.  The value will be
		 passed as the parameters of an "atm attach intf" command.

     atm_prefix_<intf>
		 (str)	For  the  ATM physical interface intf, this variable de-
		 fines the NSAP prefix for interfaces  using  a  UNI  signalling
		 manager.   If	set  to "ILMI", the prefix will automatically be
		 set via the ilmid(8) daemon.	Otherwise,  the  value	will  be
		 passed as the parameters of an "atm set prefix intf" command.

     atm_macaddr_<intf>
		 (str)	For  the  ATM physical interface intf, this variable de-
		 fines the MAC address for interfaces  using  a  UNI  signalling
		 manager.  If set to "NO", the hardware MAC address contained in
		 the ATM interface card will be used.  Otherwise, the value will
		 be passed as the parameters of an "atm set mac intf" command.

     atm_arpserver_<netif>
		 (str)	For  the  ATM network interface netif, this variable de-
		 fines the ATM address for a host which  is  to  provide  ATMARP
		 service.   This variable is only applicable to interfaces using
		 a UNI signalling manager.  If set to "local",	this  host  will
		 become an ATMARP server.  The value will be passed as the para-
		 meters of an "atm set arpserver netif" command.

     atm_scsparp_<netif>
		 (bool) If set to "YES", SCSP/ATMARP service for the network in-
		 terface  netif  will  be  initiated  using the scspd(8) and at-
		 marpd(8)  daemons.   This  variable  is  only	 applicable   if
		 atm_arpserver_<netif> is set to "local".

     atm_pvcs	 (str)	Set  to  the list of ATM PVCs to be added at system boot
		 time.	For each whitespace separated element in the  value,  an
		 atm_pvc_<element>  variable  is assumed to exist.  The value of
		 each of these variables will be passed as the parameters of  an
		 "atm add pvc" command.

     atm_arps	 (str)	Set to the list of permanent ATM ARP entries to be added
		 at system boot time.  For each whitespace separated element  in
		 the  value,  an atm_arp_<element> variable is assumed to exist.
		 The value of each of these variables will be passed as the  pa-
		 rameters of an "atm add arp" command.

     natm_interfaces
		 (str)	Set  to the list of natm(4) interfaces that will also be
		 used for HARP through harp(4).  If this list is not  empty  all
		 interfaces  in the list will be brought up with ifconfig(8) and
		 harp(4) will be loaded.  For this to work the interface drivers
		 must be either compiled into the kernel or must reside  on  the
		 root partition.

     keybell	 (str)	The  keyboard  bell  sound.   Set to "normal", "visual",
		 "off", or "NO" if the default behavior  is  desired.	For  de-
		 tails, refer to the kbdcontrol(1) manpage.

     keyboard	 (str)	If  set to a non-null string, the virtual console's key-
		 board input is set to this device.

     keymap	 (str) If set to "NO", no keymap  is  installed,  otherwise  the
		 value	  is	used	to    install	the   keymap   file   in
		 /usr/share/syscons/keymaps/<value>.kbd.

     keyrate	 (str) The keyboard repeat  speed.   Set  to  "slow",  "normal",
		 "fast", or "NO" if the default behavior is desired.

     keychange	 (str)	If not set to "NO", attempt to program the function keys
		 with the value.  The value should be a  single  string  of  the
		 form: "funkey_number new_value [funkey_number new_value ...]".

     cursor	 (str)	 Can   be   set  to  the  value  of  "normal",	"blink",
		 "destructive", or "NO" to set the cursor behavior explicitly or
		 choose the default behavior.

     scrnmap	 (str) If set to "NO", no screen map is installed, otherwise the
		 value	is  used   to	install   the	screen	 map   file   in
		 /usr/share/syscons/scrnmaps/<value>.

     font8x16	 (str)	If  set to "NO", the default 8x16 font value is used for
		 screen    size    requests,	otherwise    the    value     in
		 /usr/share/syscons/fonts/<value> is used.

     font8x14	 (str)	If  set to "NO", the default 8x14 font value is used for
		 screen    size    requests,	otherwise    the    value     in
		 /usr/share/syscons/fonts/<value> is used.

     font8x8	 (str)	If  set  to "NO", the default 8x8 font value is used for
		 screen    size    requests,	otherwise    the    value     in
		 /usr/share/syscons/fonts/<value> is used.

     blanktime	 (int)	If  set to "NO", the default screen blanking interval is
		 used, otherwise it is set to value seconds.

     saver	 (str) If not set to "NO", this is the actual  screen  saver  to
		 use (blank, snake, daemon, etc).

     moused_nondefault_enable
		 (str) If set to "NO", the mouse device specified on the command
		 line	is   not   automatically   treated  as	enabled  by  the
		 /etc/rc.d/moused script.  Having this variable set to "YES" al-
		 lows a usb(4) mouse, for example, to be enabled as soon  as  it
		 is plugged in.

     moused_enable
		 (str)	If set to "YES", the moused(8) daemon is started for do-
		 ing cut/paste selection on the console.

     moused_type
		 (str) This is the protocol type of the mouse connected to  this
		 host.	 This  variable  must  be set if moused_enable is set to
		 "YES".  The moused(8) daemon is able to detect the  appropriate
		 mouse	type  automatically in many cases.  Set this variable to
		 "auto" to let the daemon detect it, or select one from the fol-
		 lowing list if the automatic detection fails.

		 If the mouse is attached to the PS/2 mouse port, choose  "auto"
		 or  "ps/2",  regardless  of  the  brand and model of the mouse.
		 Likewise, if the mouse is  attached  to  the  bus  mouse  port,
		 choose  "auto" or "busmouse".	All other protocols are for ser-
		 ial mice and will not work with the PS/2 and bus mice.  If this
		 is a USB mouse, "auto" is the only  protocol  type  which  will
		 work.

		 microsoft	 Microsoft mouse (serial)
		 intellimouse	 Microsoft IntelliMouse (serial)
		 mousesystems	 Mouse systems Corp. mouse (serial)
		 mmseries	 MM Series mouse (serial)
		 logitech	 Logitech mouse (serial)
		 busmouse	 A bus mouse
		 mouseman	 Logitech MouseMan and TrackMan (serial)
		 glidepoint	 ALPS GlidePoint (serial)
		 thinkingmouse	 Kensington ThinkingMouse (serial)
		 ps/2		 PS/2 mouse
		 mmhittab	 MM HitTablet (serial)
		 x10mouseremote  X10 MouseRemote (serial)
		 versapad	 Interlink VersaPad (serial)

		 Even  if the mouse is not in the above list, it may be compati-
		 ble with one in  the  list.   Refer  to  the  manual  page  for
		 moused(8) for compatibility information.

		 It  should  also be noted that while this is enabled, any other
		 client of the mouse (such as an X  server)  should  access  the
		 mouse through the virtual mouse device, /dev/sysmouse, and con-
		 figure  it  as a "sysmouse" type mouse, since all mouse data is
		 converted to this single canonical format when using moused(8).
		 If the client program does not  support  the  "sysmouse"  type,
		 specify  the  "mousesystems"  type.  It is the second preferred
		 type.

     moused_port
		 (str) If moused_enable is set to "YES", this is the actual port
		 the mouse is on.  It might be	/dev/cuad0  for  a  COM1  serial
		 mouse, /dev/psm0 for a PS/2 mouse or /dev/mse0 for a bus mouse,
		 for example.

     moused_flags
		 (str)	If  moused_flags  is  set, its value is used as an addi-
		 tional set of flags to pass to the moused(8) daemon.

     moused_XXX_flags
		 When moused_nondefault_enable is enabled, and a moused(8)  dae-
		 mon is started for a non-default port, the moused_XXX_flags set
		 of  options  has  precedence  over  and  replaces  the  default
		 moused_flags (where XXX is the name of  the  non-default  port,
		 i.e.  ums0).  By setting moused_XXX_flags it is possible to set
		 up a different set of default	flags  for  each  moused(8)  in-
		 stance.   For	example,  you  can  use  "-3"  for  the  default
		 moused_flags to make your laptop's touchpad more comfortable to
		 use, but an empty set of  options  for  moused_ums0_flags  when
		 your usb(4) mouse has three or more buttons.

     mousechar_start
		 (int)	If set to "NO", the default mouse cursor character range
		 0xd0-0xd3 is used, otherwise the range start is  set  to  value
		 character,  see vidcontrol(1).  Use if the default range is oc-
		 cupied in the language code table.

     allscreens_flags
		 (str) If set, vidcontrol(1) is run with these options for  each
		 of  the  virtual  terminals (/dev/ttyv*).  For example, "-m on"
		 will enable the mouse	pointer  on  all  virtual  terminals  if
		 moused_enable is set to "YES".

     allscreens_kbdflags
		 (str)	If set, kbdcontrol(1) is run with these options for each
		 of the virtual terminals (/dev/ttyv*).  For example,  "-h  200"
		 will  set  the  syscons(4)  scrollback  (history) buffer to 200
		 lines.

     cron_enable
		 (bool) If set to "YES", run the cron(8) daemon at  system  boot
		 time.

     cron_program
		 (str) Path to cron(8) (default /usr/sbin/cron).

     cron_flags  (str)	If  cron_enable  is set to "YES", these are the flags to
		 pass to cron(8).

     cron_dst	 (bool) If set to "YES", enable the special handling of  transi-
		 tions	to and from the Daylight Saving Time in cron(8) (equiva-
		 lent to using the flag -s).

     lpd_program
		 (str) Path to lpd(8) (default /usr/sbin/lpd).

     lpd_enable  (bool) If set to "YES", run the lpd(8) daemon	at  system  boot
		 time.

     lpd_flags	 (str)	If  lpd_enable	is  set to "YES", these are the flags to
		 pass to the lpd(8) daemon.

     chkprintcap_enable
		 (bool) If set to "YES", run the chkprintcap(8)  command  before
		 starting the lpd(8) daemon.

     chkprintcap_flags
		 (str)	If  lpd_enable	and chkprintcap_enable are set to "YES",
		 these are the flags to pass to the chkprintcap(8) program.  The
		 default is "-d", which causes missing directories  to	be  cre-
		 ated.

     mta_start_script
		 (str)	This  variable	specifies the full path to the script to
		 run  to  start  a  mail  transfer  agent.    The   default   is
		 /etc/rc.sendmail.	The	sendmail_*    variables    which
		 /etc/rc.sendmail uses are documented in the rc.sendmail(8) man-
		 ual page.

     dumpdev	 (str) Indicates the device (usually a swap partition) to  which
		 a  crash dump should be written in the event of a system crash.
		 If the value of this variable is  "AUTO",  the  first	suitable
		 swap  device  listed in /etc/fstab will be used as dump device.
		 Otherwise, the value of this variable is passed as the argument
		 to dumpon(8).	To disable crash dumps,  set  this  variable  to
		 "NO".

     dumpdir	 (str) When the system reboots after a crash and a crash dump is
		 found	 on  the  device  specified  by  the  dumpdev  variable,
		 savecore(8) will save that crash dump and a copy of the  kernel
		 to  the  directory  specified by the dumpdir variable.  The de-
		 fault value is /var/crash.  Set to "NO" to not run  savecore(8)
		 at boot time when dumpdir is set.

     savecore_flags
		 (str)	If  crash dumps are enabled, these are the flags to pass
		 to the savecore(8) utility.

     quota_enable
		 (bool) Set to "YES" to turn on user and group	disk  quotas  on
		 system  startup via the quotaon(8) command for all file systems
		 marked as having quotas enabled in /etc/fstab.  The kernel must
		 be built with options QUOTA for disk quotas to function.

     check_quotas
		 (bool) Set to "YES" to enable user and group disk quota  check-
		 ing via the quotacheck(8) command.

     quotacheck_flags
		 (str)	If quota_enable is set to "YES", and check_quotas is set
		 to "YES", these are the flags	to  pass  to  the  quotacheck(8)
		 utility.  The default is "-a", which checks quotas for all file
		 systems with quotas enabled in /etc/fstab.

     quotaon_flags
		 (str)	If  quota_enable is set to "YES", these are the flags to
		 pass to the quotaon(8) utility.  The default is "-a", which en-
		 ables quotas for  all	file  systems  with  quotas  enabled  in
		 /etc/fstab.

     quotaoff_flags
		 (str)	If  quota_enable is set to "YES", these are the flags to
		 pass to the quotaoff(8) utility when shutting	down  the  quota
		 system.   The	default  is  "-a", which disables quotas for all
		 file systems with quotas enabled in /etc/fstab.

     accounting_enable
		 (bool) Set to "YES" to enable system accounting through the ac-
		 cton(8) facility.

     ibcs2_enable
		 (bool) Set to "YES" to enable iBCS2 (SCO) binary  emulation  at
		 system initial boot time.

     ibcs2_loaders
		 (str)	If  not set to "NO" and if ibcs2_enable is set to "YES",
		 this specifies a list of additional iBCS2 loaders to enable.

     linux_enable
		 (bool) Set to "YES" to enable	Linux/ELF  binary  emulation  at
		 system initial boot time.

     svr4_enable
		 (bool) If set to "YES", enable SysVR4 emulation at boot time.

     sysvipc_enable
		 (bool)  If  set  to "YES", load System V IPC primitives at boot
		 time.

     clear_tmp_enable
		 (bool) Set to "YES" to have /tmp cleaned at startup.

     clear_tmp_X
		 (bool) Set to "NO" to disable removing of X11 lock  files,  and
		 the  removal  and (secure) recreation of the various socket di-
		 rectories for X11 related programs.

     ldconfig_paths
		 (str) Set to the list of shared library paths to use  with  ld-
		 config(8).   NOTE:  /usr/lib  will always be added first, so it
		 need not appear in this list.

     ldconfig32_paths
		 (str) Set to the list of 32-bit  compatibility  shared  library
		 paths to use with ldconfig(8).

     ldconfig_paths_aout
		 (str)	Set  to the list of shared library paths to use with ld-
		 config(8) legacy a.out(5) support.

     ldconfig_insecure
		 (bool) The ldconfig(8) utility normally refuses to use directo-
		 ries which are writable by anyone except root.  Set this  vari-
		 able  to  "YES"  to  disable  that security check during system
		 startup.

     ldconfig_local_dirs
		 (str) Set to the list of local  ldconfig(8)  directories.   The
		 names	of all files in the directories listed will be passed as
		 arguments to ldconfig(8).

     ldconfig_local32_dirs
		 (str) Set to the list of local 32-bit compatibility ldconfig(8)
		 directories.  The names of all files in the directories  listed
		 will be passed as arguments to "ldconfig -32".

     kern_securelevel_enable
		 (bool)  Set to "YES" to set the kernel security level at system
		 startup.

     kern_securelevel
		 (int) The kernel security level to set at startup.  The allowed
		 range of value ranges from -1 (the compile time default)  to  3
		 (the  most  secure).	See security(7) for the list of possible
		 security levels and their effect on system operation.

     sshd_program
		 (str) Path to the SSH server program (/usr/sbin/sshd is the de-
		 fault).

     sshd_enable
		 (bool) Set to "YES" to start sshd(8) at system boot time.

     sshd_flags  (str) If sshd_enable is set to "YES", these are  the  flags  to
		 pass to the sshd(8) daemon.

     ftpd_program
		 (str)	Path to the FTP server program (/usr/libexec/ftpd is the
		 default).

     ftpd_enable
		 (bool) Set to "YES" to start ftpd(8) as a stand-alone daemon at
		 system boot time.

     ftpd_flags  (str) If ftpd_enable is set to "YES", these are the  additional
		 flags to pass to the ftpd(8) daemon.

     watchdogd_enable
		 (bool)  If  set to "YES", start the watchdogd(8) daemon at boot
		 time.	This requires that the kernel have been compiled with  a
		 watchdog(4) compatible device.

     watchdogd_flags
		 (str)	If watchdogd_enable is set to "YES", these are the flags
		 passed to the watchdogd(8) daemon.

     performance_cx_lowest
		 (str) CPU idle state to use while  on	AC  power.   The  string
		 "LOW"	indicates that acpi(4) should use the lowest power state
		 available while "HIGH" indicates that the lowest latency  state
		 (less power savings) should be used.

     performance_cpu_freq
		 (str) CPU clock frequency to use while on AC power.  The string
		 "LOW" indicates that cpufreq(4) should use the lowest frequency
		 available  while  "HIGH"  indicates  that the highest frequency
		 (less power savings) should be used.

     economy_cx_lowest
		 (str) CPU idle state to use when  off	AC  power.   The  string
		 "LOW"	indicates that acpi(4) should use the lowest power state
		 available while "HIGH" indicates that the lowest latency  state
		 (less power savings) should be used.

     economy_cpu_freq
		 (str) CPU clock frequency to use when off AC power.  The string
		 "LOW" indicates that cpufreq(4) should use the lowest frequency
		 available  while  "HIGH"  indicates  that the highest frequency
		 (less power savings) should be used.

     jail_enable
		 (bool) If set	to  "NO",  any	configured  jails  will  not  be
		 started.

     jail_parallel_start
		 (bool)  If set to "YES" all configured jails will be started in
		 the background (= in parallel).

     jail_list	 (str) A space separated list  of  names  for  jails.	This  is
		 purely  a configuration aid to help identify and configure mul-
		 tiple jails.  The names specified in this list will be used  to
		 identify  settings  common to an instance of a jail, and should
		 contain alphanumeric characters only.	Assuming that  the  jail
		 in  question  was named vjail, you would have the following de-
		 pendent variables:

		 jail_vjail_hostname="jail.example.com"
		 jail_vjail_ip="192.0.2.100"
		 jail_vjail_rootdir="/var/jails/vjail/root"

     jail_flags  (str) Unset by default.  When set, use  as  default  value  for
		 jail_<jname>_flags for every jail in jail_list.

     jail_interface
		 (str)	Unset  by  default.   When set, use as default value for
		 jail_<jname>_interface for every jail in jail_list.

     jail_fstab  (str) Unset by default.  When set, use  as  default  value  for
		 jail_<jname>_fstab for every jail in jail_list.

     jail_mount_enable
		 (bool)  Set  to  "NO"	by  default.   When  set  to "YES", sets
		 jail_<jname>_mount_enable to "YES" by default for every jail in
		 jail_list.

     jail_devfs_ruleset
		 (str)	   Unset     by     default.	  When	   set,     sets
		 jail_<jname>_devfs_ruleset  to  given	value  for every jail in
		 jail_list.

     jail_devfs_enable
		 (bool) Set to	"NO"  by  default.   When  set	to  "YES",  sets
		 jail_<jname>_devfs_enable to "YES" by default for every jail in
		 jail_list.

     jail_fdescfs_enable
		 (bool)  Set  to  "NO"	by  default.   When  set  to "YES", sets
		 jail_<jname>_fdescfs_enable to "YES" by default for every  jail
		 in jail_list.

     jail_procfs_enable
		 (bool)  Set  to  "NO"	by  default.   When  set  to "YES", sets
		 jail_<jname>_fdescfs_enable to "YES" by default for every  jail
		 in jail_list.

     jail_exec_prestart<N>
		 (str)	Unset  by  default.   When set, use as default value for
		 jail_<jname>_exec_prestart<N> for every jail in jail_list.

     jail_exec_start
		 (str) Unset by default.  When set, use  as  default  value  for
		 jail_<jname>_exec_start for every jail in jail_list.

     jail_exec_afterstart<N>
		 (str)	Unset  by  default.   When set, use as default value for
		 jail_<jname>_exec_afterstart<N> for every jail in jail_list.

     jail_exec_poststart<N>
		 (str) Unset by default.  When set, use  as  default  value  for
		 jail_<jname>_exec_poststart<N> for every jail in jail_list.

     jail_exec_prestop<N>
		 (str)	Unset  by  default.   When set, use as default value for
		 jail_<jname>_exec_prestop<N> for every jail in jail_list.

     jail_exec_stop
		 Unset	by  default.   When  set,  use	as  default  value   for
		 jail_<jname>_exec_stop for every jail in jail_list.

     jail_exec_poststop<N>
		 (str)	Unset  by  default.   When set, use as default value for
		 jail_<jname>_exec_poststop<N> for every jail in jail_list.

     jail_<jname>_rootdir
		 (str) Unset by default.  Set to the root directory used by jail
		 jname.

     jail_<jname>_hostname
		 (str) Unset by default.  Set to the fully qualified domain name
		 (FQDN) assigned to jail jname.

     jail_<jname>_ip
		 (str) Unset by default.  Set to the (primary) IPv4 and/or  IPv6
		 address(es)  assigned	to the jail.  The argument can be a sole
		 address or a comma separated list of  addresses.   Additionally
		 each  address	can be prefixed by the name of an interface fol-
		 lowed	by  a  pipe  to  overwrite   jail_<jname>_interface   or
		 jail_interface  and/or suffixed by a netmask, prefixlen or pre-
		 fix.  In case no netmask, prefixlen or prefix is  given,  `/32'
		 will  be  used for IPv4 and `/128' will be used for an IPv6 ad-
		 dress.  If no address is given for the jail then the jail  will
		 be started with no networking support.

     jail_<jname>_ip_multi<n>
		 (str)	Unset  by  default.  Set additional IPv4 and/or IPv6 ad-
		 dress(es) assigned to	the  jail.   The  sequence  starts  with
		 "_multi0" and the numbers have to be strictly ascending.  These
		 entries follow the same syntax as their primary jail_<jname>_ip
		 entry.   The order of the entries can be important as the first
		 address for each address family found will be the  primary  ad-
		 dress of the jail.  See ip-addresses option in jail(8) for more
		 details.

     jail_<jname>_flags
		 (str)	Set to "-l -U root" by default.  These are flags to pass
		 to jail(8).

     jail_<jname>_interface
		 (str) Unset by default.  When set, sets the  interface  to  use
		 when  setting IP address alias.  Note that the alias is created
		 at jail startup and removed at jail shutdown.

     jail_<jname>_fib
		 (str) Unset by default.  When set, the jail is started with the
		 specified forwarding table (sometimes referred to as a  routing
		 table) via setfib(1).

     jail_<jname>_fstab
		 (str)	Set  to /etc/fstab.<jname> by default.	This is the file
		 system information file to use for jail jname.

     jail_<jname>_mount_enable
		 (bool) Set to "NO" by default.  When set to  "YES",  mount  all
		 file systems from jail_<jname>_fstab at jail startup.

     jail_<jname>_devfs_ruleset
		 (str) Unset by default.  When set, defines the device file sys-
		 tem ruleset file to use for jail jname.

     jail_<jname>_devfs_enable
		 (bool)  Set  to  "NO" by default.  When set to "YES", mount the
		 device file system inside jail jname at jail startup.

     jail_<jname>_fdescfs_enable
		 (bool) Set to "NO" by default.  When set to  "YES",  mount  the
		 file-descriptor file system inside jail jname at jail startup.

     jail_<jname>_procfs_enable
		 (bool)  Set  to  "NO" by default.  When set to "YES", mount the
		 process file system inside jail jname at jail startup.

     jail_<jname>_exec_prestart<N>
		 (str) Unset by default.  This is the command run as Nth command
		 before jail startup, where N is 0, 1, and so  on.   It  is  run
		 outside the jail.

     jail_<jname>_exec_start
		 (str) Set to "/bin/sh /etc/rc" by default.  This is the command
		 executed in a jail at jail startup.

     jail_<jname>_exec_afterstart<N>
		 (str) Unset by default.  This is the command run as Nth command
		 in a jail after jail startup, where N is 1, 2, and so on.

     jail_<jname>_exec_poststart<N>
		 (str) Unset by default.  This is the command run as Nth command
		 after jail startup, where N is 0, 1, and so on.  It is run out-
		 side the jail.

     jail_<jname>_exec_prestop<N>
		 (str) Unset by default.  This is the command run as Nth command
		 before  jail  shutdown,  where N is 0, 1, and so on.  It is run
		 outside the jail.

     jail_<jname>_exec_stop
		 (str) Set to "/bin/sh /etc/rc.shutdown" by  default.	This  is
		 the command executed in a jail at jail shutdown.

     jail_<jname>_exec_poststop<N>
		 (str) Unset by default.  This is the command run as Nth command
		 after	jail  shutdown,  where	N is 0, 1, and so on.  It is run
		 outside the jail.

     jail_set_hostname_allow
		 (bool) If set to "NO", do not allow the root user in a jail  to
		 set its hostname.

     jail_socket_unixiproute_only
		 (bool)  If  set  to  "YES",  do  not allow any sockets, besides
		 UNIX/IP/route sockets, to be used within a jail.

     jail_sysvipc_allow
		 (bool) If set to "YES", allow applications within a jail to use
		 System V IPC.

     harvest_interrupt
		 (bool) Set to "YES" to use hardware interrupts  as  an  entropy
		 source.  Refer to random(4) for more information.

     harvest_ethernet
		 (bool)  Set  to  "YES" to use LAN traffic as an entropy source.
		 Refer to random(4) for more information.

     harvest_p_to_p
		 (bool) Set to "YES" to use serial line traffic  as  an  entropy
		 source.  Refer to random(4) for more information.

     entropy_dir
		 (str) Set to "NO" to disable caching entropy via cron(8).  Oth-
		 erwise set to the directory used to store entropy files in.

     entropy_file
		 (str)	Set  to "NO" to disable caching entropy through reboots.
		 Otherwise set to the filename	used  to  store  cached  entropy
		 through  reboots.  This file should be located on the root file
		 system to seed the random(4) device as early as possible in the
		 boot process.

     entropy_save_sz
		 (int) Size of the entropy cache files saved by save-entropy pe-
		 riodically.

     entropy_save_num
		 (int) Number of entropy cache files to save by save-entropy pe-
		 riodically.

     ipsec_enable
		 (bool) Set to "YES" to run  setkey(8)	on  ipsec_file	at  boot
		 time.

     ipsec_file  (str) Configuration file for setkey(8).

     dmesg_enable
		 (bool)  Set to "YES" to save dmesg(8) to /var/run/dmesg.boot on
		 boot.

     rcshutdown_timeout
		 (int) If set, start a watchdog timer in  the  background  which
		 will  terminate  rc.shutdown  if  shutdown(8) has not completed
		 within the specified time (in seconds).  Notice that  in  addi-
		 tion  to this soft timeout, init(8) also applies a hard timeout
		 for the execution  of	rc.shutdown.   This  is  configured  via
		 sysctl(8)  variable  kern.init_shutdown_timeout and defaults to
		 120 seconds.  Setting the value of rcshutdown_timeout	to  more
		 than  120 seconds will have no effect until the sysctl(8) vari-
		 able kern.init_shutdown_timeout is also increased.

     virecover_enable
		 (bool) Set to "NO" to prevent the system from trying to recover
		 pre-maturely terminated vi(1) sessions.

     ugidfw_enable
		 (bool) Set to "YES" to load the mac_bsdextended(4) module  upon
		 system initialization and load a default ruleset file.

     bsdextended_script
		 (str) The default mac_bsdextended(4) ruleset file to load.  The
		 default value of this variable is /etc/rc.bsdextended.

     newsyslog_enable
		 (bool) If set to "YES", run newsyslog(8) command at startup.

     newsyslog_flags
		 (str)	If newsyslog_enable is set to "YES", these are the flags
		 to pass to the newsyslog(8) program.	The  default  is  "-CN",
		 which causes log files flagged with a C to be created.

     mdconfig_md<X>
		 (str)	Arguments to mdconfig(8) for md(4) device X.  At minimum
		 a -t type must be specified and either a -s size for malloc  or
		 swap  backed  md(4) devices or a -f file for vnode backed md(4)
		 devices.  Note that mdconfig_md<X> variables are evaluated  un-
		 til one variable is unset or null.

     mdconfig_md<X>_newfs
		 (str) Optional arguments passed to newfs(8) to initialize md(4)
		 device X.

     mdconfig_md<X>_owner
		 (str)	An  ownership specification passed to chown(8) after the
		 specified md(4) device X has been mounted.  Both the md(4)  de-
		 vice and the mount point will be changed.

     mdconfig_md<X>_perms
		 (str)	A  mode  string  passed  to chmod(1) after the specified
		 md(4) device X has been mounted.  Both the md(4) device and the
		 mount point will be changed.

     mdconfig_md<X>_files
		 (str) Files to be copied to the mount point of the md(4) device
		 X after it has been mounted.

     mdconfig_md<X>_cmd
		 (str) Command to execute after the specified md(4) device X has
		 been mounted.	Note that the command is passed to eval and that
		 both _dev and _mp variables can be used  to  reference  respec-
		 tively the md(4) device and the mount point.  Assuming that the
		 md(4) device is md0, one could set the following:

		 mdconfig_md0_cmd="tar xfzC /var/file.tgz \${_mp}"

     autobridge_interfaces
		 (str) Set to the list of bridge interfaces that will have newly
		 arriving  interfaces checked against to be automatically added.
		 If not set to "NO" then for each whitespace  separated  element
		 in the value, a autobridge_<element> variable is assumed to ex-
		 ist which has a whitespace separated list of interface names to
		 match, these names can use wildcards.	For example:

		 autobridge_interfaces="bridge0"
		 autobridge_bridge0="tap* dc0 vlan[345]"

     mixer_enable
		 (bool) If set to "YES", enable support for sound mixer.

     hcsecd_enable
		 (bool) If set to "YES", enable Bluetooth security daemon.

     hcsecd_config
		 (str)	  Configuration    file    for	  hcsecd(8).	 Default
		 /etc/bluetooth/hcsecd.conf.

     sdpd_enable
		 (bool) If set to "YES", enable Bluetooth Service Discovery Pro-
		 tocol daemon.

     sdpd_control
		 (str) Path to sdpd(8) control socket.	Default /var/run/sdp.

     sdpd_groupname
		 (str) Sets sdpd(8) group to run as after it  initializes.   De-
		 fault "nobody".

     sdpd_username
		 (str)	Sets  sdpd(8)  user to run as after it initializes.  De-
		 fault "nobody".

     bthidd_enable
		 (bool) If set to "YES", enable Bluetooth Human Interface Device
		 daemon.

     bthidd_config
		 (str)	  Configuration    file    for	  bthidd(8).	 Default
		 /etc/bluetooth/bthidd.conf.

     bthidd_hids
		 (str)	Path  to  a file, where bthidd(8) will store information
		 about known HID devices.  Default /var/db/bthidd.hids.

     rfcomm_pppd_server_enable
		 (bool) If set to "YES", enable  Bluetooth  RFCOMM  PPP  wrapper
		 daemon.

     rfcomm_pppd_server_profile
		 (str)	The  name  of the profile to use from /etc/ppp/ppp.conf.
		 Multiple profiles can be specified here.  Also used to  specify
		 per-profile  overrides.   When the profile name contains any of
		 the characters ".-/+" they are translated to "_" for  the  pro-
		 poses of the override variable names.

     rfcomm_pppd_server_<profile>_bdaddr
		 (str)	Overrides  local  address  to listen on.  By default rf-
		 comm_pppd(8) will listen on "ANY" address.  The address can  be
		 specified as BD_ADDR or name.

     rfcomm_pppd_server_<profile>_channel
		 (str)	Overrides local RFCOMM channel to listen on.  By default
		 rfcomm_pppd(8) will listen on RFCOMM channel 1.  Must set prop-
		 erly if multiple profiles used in the same time.

     rfcomm_pppd_server_<profile>_register_sp
		 (bool) Tells rfcomm_pppd(8) if it should register  Serial  Port
		 service on the specified RFCOMM channel.  Default "NO".

     rfcomm_pppd_server_<profile>_register_dun
		 (bool)  Tells rfcomm_pppd(8) if it should register Dial-Up Net-
		 working service on the specified RFCOMM channel.  Default "NO".

     ubthidhci_enable
		 (bool) If set to "YES", change  the  USB  Bluetooth  controller
		 from  HID mode to HCI mode.  You also need to specify the loca-
		 tion of USB Bluetooth controller with the ubthidhci_busnum  and
		 ubthidhci_addr variables.

     ubthidhci_busnum
		 Bus  number  where  the  USB  Bluetooth  controller is located.
		 Check the output of usbconfig(8) on your system  to  find  this
		 information.

     ubthidhci_addr
		 Bus  address of the USB Bluetooth controller.	Check the output
		 of usbconfig(8) on your system to find this information.

     netwait_enable
		 (bool) If set to "YES", delays  the  start  of  network-reliant
		 services  until netwait_if is up and ICMP packets to a destina-
		 tion defined in netwait_ip are flowing.  Link state is examined
		 first, followed by "pinging" an IP address  to  verify  network
		 usability.   If  no  destination can be reached or timeouts are
		 exceeded, network services are started anyway with no guarantee
		 that the network is usable.  Use of this variable requires both
		 netwait_ip and netwait_if to be set.

     netwait_ip  (str) Empty by default.  This variable contains a  space-delim-
		 ited list of IP addresses to ping(8).	DNS hostnames should not
		 be  used  as  resolution  is not guaranteed to be functional at
		 this point.  If multiple IP addresses are specified, each  will
		 be tried until one is successful or the list is exhausted.

     netwait_timeout
		 (int) Indicates the total number of seconds to perform a "ping"
		 against  each	IP  address in netwait_ip, at a rate of one ping
		 per second.  If any of the pings are successful,  full  network
		 connectivity is considered reliable.  The default is 60.

     netwait_if  (str) Empty by default.  Defines the name of the network inter-
		 face  on  which watch for link.  ifconfig(8) is used to monitor
		 the interface, looking for "status: no  carrier".   Once  gone,
		 the  link is considered up.  This can be a vlan(4) interface if
		 desired.

     netwait_if_timeout
		 (int) Defines the total number of seconds to wait for	link  to
		 become  usable,  polled at a 1-second interval.  The default is
		 30.

FILES
     /etc/defaults/rc.conf
     /etc/rc.conf
     /etc/rc.conf.local

SEE ALSO
     catman(1), chmod(1), gdb(1), info(1), kbdcontrol(1), makewhatis(1),  sh(1),
     vi(1),  vidcontrol(1),  bridge(4), dummynet(4), ip(4), ipf(4), ipfw(4), ip-
     nat(4), kld(4), pf(4), pflog(4),  pfsync(4),  tcp(4),  udp(4),  exports(5),
     fstab(5),	ipf(5),  ipnat(5), motd(5), newsyslog.conf(5), pf.conf(5), secu-
     rity(7), accton(8),  amd(8),  apm(8),  atm(8),  bthidd(8),  chkprintcap(8),
     chown(8),	cron(8),  dhclient(8), ftpd(8), geli(8), hcsecd(8), ifconfig(8),
     inetd(8), ipf(8), ipfw(8), ipnat(8), jail(8),  kldxref(8),  lpd(8),  mdcon-
     fig(8),  mdmfs(8),  mixer(8),  mountd(8),	moused(8), mrouted(8), named(8),
     newfs(8), newsyslog(8), nfsd(8), ntpd(8), ntpdate(8), pfctl(8),  pflogd(8),
     ping(8),  powerd(8),  quotacheck(8), quotaon(8), rc(8), rc.sendmail(8), rf-
     comm_pppd(8), route(8), routed(8), rpcbind(8), rpc.lockd(8),  rpc.statd(8),
     rwhod(8),	savecore(8), sdpd(8), sshd(8), swapon(8), sysctl(8), syslogd(8),
     timed(8), usbconfig(8), wlandebug(8), yp(8), ypbind(8), ypserv(8), ypset(8)

HISTORY
     The rc.conf file appeared in FreeBSD 2.2.2.

AUTHORS
     Jordan K. Hubbard.

FreeBSD 9.0			December 13, 2011		      RC.CONF(5)

home | help