home | help
ISP(4)			     Kernel Interfaces Manual			  ISP(4)

NAME
     isp -- Qlogic based SCSI and FibreChannel SCSI Host Adapters

SYNOPSIS
     To compile this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device scbus
	   device isp

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):

	   isp_load="YES"

DESCRIPTION
     This driver provides access to SCSI or FibreChannel devices.

     SCSI features include support for Ultra SCSI and wide mode transactions for
     SCSI,  Ultra2  LVD  (for  the ISP1080 and ISP1280), and Ultra3 LVD (for the
     ISP12160).

     Fibre Channel support uses FCP SCSI profile for FibreChannel, and	utilizes
     Class 3 and Class 2 connections (Qlogic 2100 is Class 3 only, minor patches
     to the Qlogic 2200 to force Class 2 mode).  Support is available for Public
     and  Private  loops, and for point-to-point connections (Qlogic 2200 only).
     The newer 2-Gigabit cards (2300, 2312, 2322) and 4-Gigabit (2422, 2432) are
     also  supported.	Command  tagging  is  supported  for   all   (in   fact,
     FibreChannel  requires  tagging).	Fabric support is enabled by default for
     other than 2100 cards.  Fabric support for 2100 cards has been so	problem-
     atic  and these cards are so old now that it is just not worth your time to
     try it.

FIRMWARE
     Firmware is available if the ispfw(4) module  is  loaded  during  bootstrap
     (q.v.).

     It  is  strongly  recommended  that  you  use  the  firmware available from
     ispfw(4) as it is the most likely to have been tested with this driver.

HARDWARE
     Cards supported by the isp driver include:

	   ISP1000
		   SBus Fast Wide, Ultra Fast Wide cards, Single Ended	or  Dif-
		   ferential cards.

	   ISP1020
		   Qlogic 1020 Fast Wide and Differential Fast Wide PCI cards.

	   ISP1040
		   Qlogic 1040 Ultra Wide and Differential Ultra Wide PCI cards.
		   Also  known	as  the DEC KZPBA-CA (single ended) and KZPBA-CB
		   (HVD differential).

	   Qlogic 1240
		   Qlogic 1240 Dual Bus Ultra Wide and Differential  Ultra  Wide
		   PCI cards.

	   Qlogic 1020
		   Qlogic 1020 SCSI cards.

	   Qlogic 1040
		   Qlogic 1040 Ultra SCSI cards.

	   Qlogic 1080
		   Qlogic 1280 LVD Ultra2 Wide PCI cards.

	   Qlogic 1280
		   Qlogic 1280 Dual Bus LVD Ultra2 Wide PCI cards.

	   Qlogic 12160
		   Qlogic 12160 Dual Bus LVD Ultra3 Wide PCI cards.

	   Qlogic 210X
		   Qlogic  2100 and 2100A Copper and Optical Fibre Channel Arbi-
		   trated Loop (single, dual).

	   Qlogic 220X
		   Qlogic 2200 Copper and Optical Fibre Channel Arbitrated  Loop
		   PCI cards (single, dual, quad).

	   Qlogic 2300
		   Qlogic 2300 Optical Fibre Channel PCI cards.

	   Qlogic 2312
		   Qlogic 2312 Optical Fibre Channel PCI cards.

	   Qlogic 234X
		   Qlogic  234X  Optical  Fibre Channel PCI cards (2312 chipset,
		   single and dual attach).

	   Qlogic 2322
		   Qlogic 2322 Optical Fibre Channel PCIe cards.

	   Qlogic 200
		   Dell Branded version of the QLogic  2312  Fibre  Channel  PCI
		   cards.

	   Qlogic 2422
		   Qlogic 2422 Optical Fibre Channel PCI cards (4 Gigabit)

	   Qlogic 2432
		   Qlogic 2432 Optical Fibre Channel PCIe cards (4 Gigabit)

CONFIGURATION OPTIONS
     Target mode support may be enabled with the

     options ISP_TARGET_MODE

     option.

BOOT OPTIONS
     The    following	 options   are	 switchable   by   setting   values   in
     /boot/device.hints.

     They are:

     hint.isp.0.disable
	     A hint value to disable driver in kernel.

     hint.isp.0.fwload_disable
	     A hint value to disable loading of firmware ispfw(4).

     hint.isp.0.prefer_memmap
	     A hint value to use PCI memory space instead of  I/O  space  access
	     for.

     hint.isp.0.prefer_iomap
	     A	hint  value  to use PCI I/O space instead of Memory space access
	     for.

     hint.isp.0.ignore_nvram
	     A hint value to ignore board NVRAM  settings  for.   Otherwise  use
	     NVRAM settings.

     hint.isp.0.fullduplex
	     A hint value to set full duplex mode.

     hint.isp.0.topology
	     A	hint  value  to select topology of connection.	Supported values
	     are:

	     lport	 Prefer loopback and fallback to point to point.
	     nport	 Prefer point to point and fallback to loopback.
	     lport-only  Loopback only.
	     nport-only  Point to point only.

     hint.isp.0.portwwn
	     This should be the full 64 bit World Wide Port Name you would  like
	     to use, overriding the value in NVRAM for the card.

     hint.isp.0.nodewwn
	     This  should be the full 64 bit World Wide Node Name you would like
	     to use, overriding the value in NVRAM for the card.

     hint.isp.0.iid
	     A hint to override or set the Initiator ID or Loop ID.   For  Fibre
	     Channel  cards  in Local Loop topologies it is strongly recommended
	     that you set this value to non-zero.

     hint.isp.0.role
	     A hint to define default role for isp instance (target,  initiator,
	     both).

     hint.isp.0.debug
	     A	 hint	value	for   a   driver   debug  level  (see  the  file
	     /usr/src/sys/dev/isp/ispvar.h for the values.

SYSCTL OPTIONS
     dev.isp.N.loop_down_limit
	     This value says how long to wait in seconds  after  loop  has  gone
	     down  before  giving  up  and expiring all of the devices that were
	     visible.  The default is 300 seconds (5 minutes).	A separate (non-
	     adjustable) timeout is used when booting to  not  stop  booting  on
	     lack of FC connectivity.

     dev.isp.N.gone_device_time
	     This  value  says	how long to wait for devices to reappear if they
	     (temporarily) disappear due to loop or fabric events.   While  this
	     timeout is running, I/O to those devices will simply be held.

     dev.isp.N.wwnn
	     This is the readonly World Wide Node Name value for this port.

     dev.isp.N.wwpn
	     This is the readonly World Wide Port Name value for this port.

SEE ALSO
     da(4), intro(4), ispfw(4), sa(4), scsi(4), gmultipath(8)

AUTHORS
     The  isp  driver  was  written  by  Matthew  Jacob originally for NetBSD at
     NASA/Ames Research Center.

BUGS
     The driver currently ignores some NVRAM settings.

     Target mode support is not completely reliable yet.   It  works  reasonably
     well  for	Fibre Channel, somewhat well for Qlogic 1040 cards, but does not
     yet work for the other cards (due to last	minute	unannounced  changes  in
     firmware interfaces).

FreeBSD 9.1			February 28, 2007			  ISP(4)

home | help