home | help
TL(4)			     Kernel Interfaces Manual			   TL(4)

NAME
     tl -- Texas Instruments ThunderLAN Ethernet device driver

SYNOPSIS
     To compile this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device miibus
	   device tl

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_tl_load="YES"

DESCRIPTION
     The tl driver provides support for PCI Ethernet adapters based on the Texas
     Instruments ThunderLAN Ethernet controller chip.

     The  ThunderLAN controller has a standard MII interface that supports up to
     32 physical interface devices (PHYs).  It also has a built-in  10baseT  PHY
     hardwired at MII address 31, which may be used in some 10Mbps-only hardware
     configurations.	In  100Mbps  configurations,  a  National  Semiconductor
     DP83840A or other MII-compliant PHY may be attached to the ThunderLAN's MII
     bus.  If a DP83840A or equivalent is available, the ThunderLAN chip can op-
     erate at either 100Mbps or 10Mbps	in  either  half-duplex  or  full-duplex
     modes.  The ThunderLAN's built-in PHY and the DP83840A also support autone-
     gotiation.

     The tl driver supports the following media types:

     autoselect 	   Enable  autoselection  of the media type and options.
			   Note that this option is only available on those PHYs
			   that support autonegotiation.  Also, the PHY will not
			   advertise those modes that have been explicitly  dis-
			   abled using the following media options.

     10baseT/UTP	   Set 10Mbps operation.

     100baseTX		   Set 100Mbps (Fast Ethernet) operation.

     10base5/AUI	   Enable AUI/BNC interface (useful only with the built-
			   in PHY).

     The tl driver supports the following media options:

     full-duplex	   Force full duplex operation.

     half-duplex	   Force half duplex operation.

     hw-loopback	   Enable hardware loopback mode.

     Note  that  the  100baseTX media type is only available if supported by the
     PHY.  For more information on configuring this device, see ifconfig(8).

HARDWARE
     The tl driver supports Texas Instruments ThunderLAN based Ethernet and Fast
     Ethernet adapters including a large number of Compaq PCI Ethernet adapters.
     Also supported are:

     *	 Olicom OC-2135/2138 10/100 TX UTP adapter
     *	 Olicom OC-2325/OC-2326 10/100 TX UTP adapter
     *	 Racore 8148 10baseT/100baseTX/100baseFX adapter
     *	 Racore 8165 10/100baseTX adapter

     The tl driver also supports the built-in Ethernet adapters of various  Com-
     paq Prosignia servers and Compaq Deskpro desktop machines including:

     *	 Compaq Netelligent 10
     *	 Compaq Netelligent 10 T PCI UTP/Coax
     *	 Compaq Netelligent 10/100
     *	 Compaq Netelligent 10/100 Dual-Port
     *	 Compaq Netelligent 10/100 Proliant
     *	 Compaq Netelligent 10/100 TX Embedded UTP
     *	 Compaq Netelligent 10/100 TX UTP
     *	 Compaq NetFlex 3P
     *	 Compaq NetFlex 3P Integrated
     *	 Compaq NetFlex 3P w/BNC

DIAGNOSTICS
     tl%d: couldn't map memory	A fatal initialization error has occurred.

     tl%d: couldn't map interrupt  A fatal initialization error has occurred.

     tl%d:  device timeout  The device has stopped responding to the network, or
     there is a problem with the network connection (cable).

     tl%d: no memory for rx list  The driver failed to allocate an mbuf for  the
     receiver ring.

     tl%d:  no memory for tx list  The driver failed to allocate an mbuf for the
     transmitter ring when allocating a pad buffer or collapsing an  mbuf  chain
     into a cluster.

SEE ALSO
     arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY
     The tl device driver first appeared in FreeBSD 2.2.

AUTHORS
     The tl driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

FreeBSD 9.1			  July 16, 2005 			   TL(4)

home | help