FreeBSD Manual Pages
AUCAT(1) General Commands Manual AUCAT(1) NAME aucat -- audio file manipulation tool SYNOPSIS aucat [-dn] [-b size] [-c channels] [-e enc] [-f device] [-g position] [-h fmt] [-i file] [-m min:max/min:max] [-o file] [-p position] [-q port] [-r rate] [-v volume] DESCRIPTION The aucat utility can play, record, mix, and process audio files on the fly. During playback, aucat reads audio data concurrently from all played files, mixes it and plays the result on the device. Similarly, it stores audio data recorded from the device into corresponding files. An off-line mode could be used to process audio files without involving audio hardware. Processing includes: • Change the sound encoding. • Route the sound from one channel to another. • Control the per-file playback volume. Finally, aucat can accept MIDI messages usable for: • Volume control. • Start, stop and relocate playback and recording. The options are as follows: -b size The buffer size of the audio device in frames. Default is 7680. -c channels The audio file channels count. The default is 2, i.e. stereo. -d Increase log verbosity. -e enc Encoding of the audio file. The default is s24. Encoding names use the following scheme: signedness (s or u) followed by the precision in bits, the byte-order (le or be), the number of bytes per sample, and the alignment (msb or lsb). Only the signedness and the precision are mandatory. Examples: u8, s16le, s24le3, s24le4lsb. -f device Use this sndio(7) audio device. Device mode and parameters are determined from audio files. Default is default. -g position Go to the given time position and start playback or recording there. This option is equivalent to an incoming MMC relocate message with the same position. The position is expressed as the number of samples (at device sample rate). -h fmt Audio file type. The following file types are supported: raw Headerless file. wav Microsoft WAV file format. aiff Apple's audio interchange file format. au Sun/NeXT audio file format. auto Try to guess, depending on the file name. This is the default. -i file Play this audio file. If the option argument is `-' then stan- dard input will be used. -m min:max/min:max Map the given range of source channels into the given range of destination channels. -n Off-line mode. Read input files and store the result in the output files, processing them on the fly. This mode is useful to mix, demultiplex, resample or re-encode audio files off- line. It requires at least one input (-i) and one output (-o). -o file Record into this audio file. If the option argument is `-' then standard output will be used. -p position Time offset where the beginning of the file belongs. The first sample of the file will be played or recorded when the device reaches the given position. The position is expressed as the number of samples (at device sample rate). -q port Control audio device properties through this MIDI port. This includes per-stream volumes and the ability to synchronously start, stop and relocate audio files. -r rate Sample rate in Hertz of the audio file. The default is 48000. -v volume Software volume attenuation of the file to play. The value must be between 1 and 127, corresponding to -42dB and -0dB at- tenuation in 1/3dB steps. The default is 127, i.e. no attenua- tion. On the command line, per-file parameters (-cehmrv) must precede the file definition (-io). If aucat is sent SIGHUP, SIGINT or SIGTERM, it terminates recording to files. MIDI CONTROL aucat can be controlled through MIDI (-q) as follows: a MIDI channel is assigned to each stream, and the volume is changed using the standard volume controller (number 7). The master volume can be changed using the standard master volume system exclusive message. All audio files are controlled by the following MMC messages: relocate All files are relocated to the requested time posi- tion. If it is beyond the end of a file, the file is temporarily disabled until a valid position is re- quested. start Playback and/or recording is started. stop Playback and/or recording is stopped and all files are rewound back to the starting position. MIDI control is intended to be used together with sndiod(8). For in- stance, the following command will create two devices: the default snd/default and a MMC-controlled one snd/default.mmc: $ sndiod -r 48000 -z 480 -s default -t slave -s mmc Programs using snd/default behave normally, while programs using snd/mmc wait for the MMC start signal and start synchronously. Then, the following command will play a file on the snd/mmc audio device, giving full control to MIDI software or hardware connected to the midithru/0 MIDI port: $ aucat -f snd/mmc -q midithru/0 -i file.wav At this stage, aucat will start, stop and relocate automatically fol- lowing all user actions in the MIDI sequencer, assuming it's configured to transmit MMC on midithru/0 and snd/mmc. Furthermore, the MIDI se- quencer could be configured to use the snd/mmc port as MTC clock source, assured to be synchronous to playback of file.wav. EXAMPLES Mix and play two files while recording a third file: $ aucat -i file1.wav -i file2.wav -o file3.wav Record channels 2 and 3 into one stereo file and channels 6 and 7 into another stereo file using a 44.1kHz sampling rate for both: $ aucat -r 44100 -m 2:3/0:1 -o file1.wav -m 6:7/0:1 -o file2.wav Split a stereo file into two mono files: $ aucat -n -i stereo.wav -c 1 -m 0:0/0:0 -o left.wav \ -m 1:1/0:0 -o right.wav SEE ALSO cdio(1), audio(4), sndio(7), audioctl(8), mixerctl(8), sndiod(8) BUGS Resampling is low quality. There are limitations inherent to the wav, aiff, and au file formats: not all encodings are supported, file sizes are limited to 2GB, and the files must support the lseek(2) operation (e.g. pipes do not support it). FreeBSD Ports 14.quarterly $Mdocdate$ AUCAT(1)
NAME | SYNOPSIS | DESCRIPTION | MIDI CONTROL | EXAMPLES | SEE ALSO | BUGS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=aucat&sektion=1&manpath=FreeBSD+Ports+14.3.quarterly>