FreeBSD Manual Pages
Smokeping_probes_RemoteFPing(3) SmokePing Smokeping_probes_RemoteFPing(3) NAME Smokeping::probes::RemoteFPing - Remote FPing Probe for SmokePing SYNOPSIS *** Probes *** +RemoteFPing binary = /usr/bin/ssh # mandatory blazemode = true hostinterval = 1.5 interface = eth0 mininterval = 0.001 offset = 50% packetsize = 5000 pings = 20 protocol = 4 rbinary = /usr/bin/fping # mandatory rhost = my.pinger.host # mandatory rport = 22 ruser = foo sourceaddress = 192.168.0.1 step = 300 timeout = 1.5 tos = 0x20 usestdout = true # The following variables can be overridden in each target section /^influx_.+/ = influx_location = In the basement # [...] *** Targets *** probe = RemoteFPing # if this should be the default probe # [...] + mytarget # probe = RemoteFPing # if the default probe is something else host = my.host /^influx_.+/ = influx_location = In the basement DESCRIPTION Integrates the remote execution of FPing via ssh/rsh into smokeping. The variable binary must point to your copy of the ssh/rsh program. The vari- able rbinary must point to your copy of the fping program at the remote end. VARIABLES Supported probe-specific variables: binary This variable specifies the path of the remote shell program (usually ssh, rsh or remsh). Any other script or binary that can be called as binary [ -l ruser ] [ -p rport ] rhost rbinary may be used. Example value: /usr/bin/ssh This setting is mandatory. blazemode Send an extra ping and then discard the first answer since the first is bound to be an outlier. Example value: true hostinterval The fping "-p" parameter, but in (possibly fractional) seconds rather than milliseconds, for consistency with other Smokeping probes. From fping(1): This parameter sets the time that fping waits between successive pack- ets to an individual target. Example value: 1.5 interface The name of the network interface to perform the ping on. Example value: eth0 mininterval The fping "-i" parameter, but in (probably fractional) seconds rather than milliseconds, for consistency with other Smokeping probes. From fping(1): The minimum amount of time between sending a ping packet to any target. Example value: 0.001 Default value: 0.01 offset If you run many probes concurrently you may want to prevent them from hitting your network all at the same time. Using the probe-specific offset parameter you can change the point in time when each probe will be run. Offset is specified in % of total interval, or alternatively as 'random', and the offset from the 'General' section is used if nothing is specified here. Note that this does NOT influence the rrds itself, it is just a matter of when data acquisition is initiated. (This vari- able is only applicable if the variable 'concurrentprobes' is set in the 'General' section.) Example value: 50% packetsize The ping packet size (in the range of 12-64000 bytes). Example value: 5000 pings How many pings should be sent to each target, if different from the global value specified in the Database section. Note that the number of pings in the RRD files is fixed when they are originally generated, and if you change this parameter afterwards, you'll have to delete the old RRD files or somehow convert them. Example value: 20 protocol Choose if the ping should use IPv4 or IPv6. Example value: 4 rbinary The location of your fping binary. Example value: /usr/bin/fping This setting is mandatory. rhost The rhost option specifies the remote device from where fping will be launched. Example value: my.pinger.host This setting is mandatory. rport The (optional) rport option allows you to specify the port of the re- mote host. Example value: 22 ruser The (optional) ruser option allows you to specify the remote user, if different from the one running the smokeping daemon. Example value: foo sourceaddress The fping "-S" parameter . From fping(1): Set source address. Example value: 192.168.0.1 stepDuration of the base interval that this probe should use, if different from the one specified in the 'Database' section. Note that the step in the RRD files is fixed when they are originally generated, and if you change the step parameter afterwards, you'll have to delete the old RRD files or somehow convert them. (This variable is only applicable if the variable 'concurrentprobes' is set in the 'General' section.) Example value: 300 timeout The fping "-t" parameter, but in (possibly fractional) seconds rather than milliseconds, for consistency with other Smokeping probes. Note that as Smokeping uses the fping 'counting' mode (-C), this apparently only affects the last ping. Example value: 1.5 tos Set the type of service (TOS) of outgoing ICMP packets. You need at laeast fping-2.4b2_to3-ipv6 for this to work. Find a copy on www.smokeping.org/pub. Example value: 0x20 usestdout Listen for FPing output on stdout instead of stderr ... (version 3.3+ sends its statistics on stdout). Example value: true AUTHORS Luis F Balbinot <hades@inf.ufrgs.br> Niko Tyni <ntyni@iki.fi> derived from Smokeping::probes::FPing by Tobias Oetiker <tobi@oetiker.ch> NOTES It is important to make sure that you can access the remote machine without a password prompt, otherwise this probe will not work properly. To test just try something like this: $ ssh foo@HostA.foobar.com fping HostB.barfoo.com The next thing you see must be fping's output. The rhost, ruser, rport and rbinary variables used to be configured in the Targets section of the first target or its parents They were moved to the Probes section, because the variables aren't really target-specific (all the targets are measured with the same parameters). The Targets sections aren't recognized anymore. BUGS This functionality should be in a generic 'remote execution' module so that it could be used for the other probes too. 2.9.0 2026-08-04 Smokeping_probes_RemoteFPing(3)
NAME | SYNOPSIS | DESCRIPTION | VARIABLES | AUTHORS | NOTES | BUGS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=Smokeping_probes_RemoteFPing&sektion=3&manpath=FreeBSD+Ports+15.1.quarterly>