FreeBSD Manual Pages
cpipe(1) Programmer's Manual cpipe(1) NAME cpipe - copy stdin to stdout while counting bytes and reporting progress SYNOPSIS cpipe [-b bsize] [-vt] [-vr] [-vw] [-ngr] [-s speed] OPTIONS -b buffer size in kB, 1 Int value between 1 and oo. Default: `128' -vt show throughput. -vr show read-times. -vw show write-times. -ngr non-greedy read. Don't enforce a full buffer on read before starting to write. -s throughput speed limit in kB/s, 1 Double value between 1 and oo. DESCRIPTION Cpipe copies its standard input to its standard output while measuring the time it takes to read an input buffer and write an output buffer. If one or more of the -vx options is given, statistics of average throughput and the total amount of bytes copied are printed to the standard error output. Non Greedy Read Normally, cpipe does its best to totally fill its buffer (option -b) before it starts writing. In some situations however, e.g. if you talk to an in- teractive program via cpipe, this deadlocks the communication: said program waits for input which it will never see, because the input is stuck in cpipe's buffer. But cpipe itself will not see more input before the program does not respond. To get around this, try using -ngr. When issuing a read call, cpipe is then satisfied as soon as it gets at least one byte. Instead of filling the buffer, it stops reading and writes whatever it got to the output. Note, however, that the throughput measurements will be less exact if the number of bytes transferred in one read/write pair becomes small, because cpipe will spent relatively more time working on every byte. Limiting Throughput If a throughput limit is specified with option -s, cpipe calls usleep(3) in between copying buffers, thereby artificially extending the duration of a read/write-cycle. Since on most systems there is a certain minimum time usleep() sleeps, e.g. 0.01s, it is impossible to reach high limits with a small buffer size. In this case increasing the buffer size (option -b) might help. However, keep in mind that this limits the throughput only on the average. Every single buffer is copied as fast as possible. EXAMPLE The command tar cCf / - usr | cpipe -vr -vw -vt > /dev/null results in an output like ... in: 19.541ms at 6.4MB/s ( 4.7MB/s avg) 2.0MB out: 0.004ms at 30.5GB/s ( 27.1GB/s avg) 2.0MB thru: 19.865ms at 6.3MB/s ( 4.6MB/s avg) 2.0MB ... The first column shows the times it takes to handle one buffer of data (128kB by default). The read-call took 19.541ms, the write-call to /dev/null took just 0.004ms and from the start of the read to the end of write, it took 19.865ms. The second column shows the result of dividing the buffer size (128kB by default) by the times in the first column. The third column contains the average over all measured values from the start of the program. Finally, the last column shows the total number of bytes transferred, which is of course the same for reading and writing. BUGS This program uses precious processor cycles. Consequently the measured times will be different from the transfer rates possible without it. Instead of just non-greedy reading, full non-blocking I/O and use of se- lect(2) should be used to make sure that no deadlocks occur when communi- cating with interactive programs. CREDITS Peter Astrand <astrand@lysator.liu.se> recommended the speed limit. Ivo De Decker <ivo@zeus.rug.ac.be> asked for deadlock prevention, which is (hopefully) sufficiently covered by the non-greedy read. AUTHOR Bug reports, beer and postcards go to pifpafpuf@gmx.de. New versions will show up on http://cpipe.berlios.de/. Clig-manuals 3.0.1 cpipe(1)
NAME | SYNOPSIS | OPTIONS | DESCRIPTION | EXAMPLE | BUGS | CREDITS | AUTHOR
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=cpipe&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>