home | help
design_coupler(1)	     General Commands Manual	       design_coupler(1)

NAME
     design_coupler - for designing directional couplers (part of the atlc pack-
     age)

SYNOPSIS
     design_coupler [-C][-d][-e][-H height][-L length][-q]
     [s fstep][-Z Zo] CF fmin fmax

WARNING
     This  man	page  is not a complete set of documentation - the complexity of
     the atlc project makes man pages not an ideal way to document it,	although
     out  of  completeness, man pages are produced.  The best documentation that
     was current at the time this version was produced should be found	on  your
     hard drive, usually at
     /usr/local/share/atlc/docs/html-docs/index.html
     although  it  might  be elsewhere if your system administrator chose to in-
     stall the package elsewhere. Sometimes, errors are corrected in  the  docu-
     mentation	and  placed at http://atlc.sourceforge.net/ before a new release
     of atlc is released.  Please, if you notice a problem with  the  documenta-
     tion - even spelling errors and typos, please let me know.

DESCRIPTION
     design_coupler  is  used  to design directional couplers. It it not used to
     analyse couplers for which you know the dimensions. Instead, it is used but
     when you require a coupler to have specific properties, but don't know  the
     required  odd  and even mode impedances or the required physical dimensions
     that will achieve those required properties.

     As a minimum the user must specify the coupling factor CF in dB, the  mini-
     mum frequency fmin in MHz and the maximum frequency fmax in MHz.  With this
     information, the design_coupler will
     a) Tell you the required odd and even mode impedances Zodd and Zeven assum-
     ing  the  coupler	is  for 50 Ohms and assuming the coupler is is a quarter
     wave long, which might be an impractical length. There a numerous	ways  of
     making a coupler having those impedances and design_coupler does not (with-
     out  the  addition of options mentioned later), tell you how to make such a
     coupler.  b) Given you the frequency response of the  coupler,  making  the
     assumptions  about  the  50 Ohm impedance and quarter-wave length. The fre-
     quency response is calculated at 5 points in the range  specified	by  fmin
     and fmax.

     By  use of the -Z 'Zo' and -L 'length' and -f 'fstep' options it it posible
     to specify different a different characteristic impedance, length and  dif-
     ferent frequency steps to display the frequency response.

     The computed  values of Zodd and Zeven required are valid no matter how the
     coupler  is  design  physically. So no matter whether it's implemented on a
     PCB, air spaced or whatever, the above impedances are correct and the  fre-
     quency response is correct.

     The -d option causes design_coupler to not only report the required odd and
     even  modem  impedances  but also the physical dimensions of a coupler that
     achieves these properties! Currently, the only stucture  for  which  it  is
     possible  to  compute  the  physical  dimentions  is  two wide edge-coupled
     striplines between two wide plates like this:

     -----------------------------------------------------  ^
     |							 |  |
     |			Er				 |  |
     |							 |  |
     |		  -----------	    ----------- 	 |  H
     |		  <----w----><--s--><----w----> 	 |  |
     |							 |  |
     |							 |  |
     |							 |  |
     -----------------------------------------------------  v
     <-------------------------W------------------------->

     The width W must be much greater than the height of the coupler and  gener-
     ally  it  is assumed that this width will at least 2*w+s*5*H, otherwise the
     calculations will be incorrect. In order to calculate these dimenisions  an
     analytical  method is used, which is only valid if the width W is infinity,
     but should be resonably good assuming W is at least 2*w+s+5*H.

     It is later intended to enable design  coupler  to  use  other  structures,
     which  migth be more suitable for construction, such as microstrip couplers
     on PCBs, but for now at least, it is only possible to compute the	physical
     dimensions  of  the  coupler  using the above stucture. For strong coupling
     (less than 20 dB or so), the dimenions calculated might be impractical,  as
     the  spacing  s will be so small. However, for weak coupling, the physcical
     dimensions are practical.

OPTIONS
     -C
     print copyright, licensing and copying information.
     -d
     Design a coupler, using two edgle-coupled stiplines inside a  wide  4-sided
     rectangular enclosure.

     -e
     Priont an example of how to use design_coupler
     -H height
     Specify  the height of the enclosure in some convenient unit. By default, a
     height of 1 unit is assumed, but by use of this option it	is  possible  to
     specify  any height you want. Since its the ratio of dimensions that is im-
     portant, not the absolute values, this just scales all the other dimensions
     by the specified height. It is just a conveneince for the user.
     -L length
     Specifies the coupler length in metres. By default the coupler  is  assumed
     to  be  a	quarter-wave,  but this allow any length you want. Don't chose a
     length that is a multiple of a half-wave though, as this will make  it  im-
     possible to couple any power out.	-q
     This  is the 'quite' switch and causes design_coupler to print out less in-
     formation. One can use -qq to cause the even less output.
     -s fstep Causes design_couler to print out the frequency response	at  dif-
     ferent  steps  from the default 5 values. fstep must be in MHz. The default
     value of fstep is obviously (fmax-fman)/5.
     Z Zo
     Causes design_coupler to compute properties of an impedance  Zo  (shecified
     in Ohms). The default value for Zo is 50 Ohms.

EXAMPLES
     Run  design_coupler gives examples of its use. However, here are those same
     examples.

     Here are a examples of how to use design_coupler In  the  examples,  the  %
     sign  is  used  in  front	of anything you must type which is what you will
     probably see when using the csh or tcsh as a shell. It would probably be  a
     $ sign if using the sh or bash shell.

     To find the odd and even mode impedances and frequency response of a 50 Ohm
     coupler, covering 130 to 170 MHz, with a coupling coefficient of 30 dB:

     % design_coupler 30 130 170

     Note  the	frequency  response is symmetrical about the centre frequency at
     0.192 dB below that wanted. You may wish to redesign this	for  a	coupling
     coefficient  of about 29.9 dB, so the maximum deviation from the ideal 30.0
     dB never exceeds 0.1 dB Note the length suggested is 0.5 m (nearly 20")  is
     a	quarter  wave  at the centre frequency of 150 MHz. You might find this a
     bit too long, so let's specify a length of 0.25 m.

     % design_coupler -L 0.25 30 130 170

     What you may notice is that while the coupling to the coupled port  is  ex-
     actly  30	dB below the input power at the centre frequency (150 MHz) it is
     no longer symmetrical about the centre frequency. Also, deviations from the
     ideal 30 dB are now much larger, with a maximum error of  1.012  dB  Unlike
     the case when the length is the default quarter wave, there is not much you
     can do about this, since the deviations occur in both directions.

     Now  assume  you  are reasonably happy with the response when the length is
     250 mm but would like to see the response at every 2.5  MHz.  This  can  be
     done using the -s option to design_coupler.

     % design_coupler -L 0.25 -s 2.5 30 130 170

     Assuming  the  performance is acceptable, the dimensions of the coupler can
     be determined by adding the -d option. This will design a coupler that must
     look like the structure below. The two inner conductors, which  are  spaced
     equally  between  the  top and bottom edges of the outer conductor, must be
     very thin.  These are placed along the length of a box of width W, height H
     and of a length L determined by the user, which in this case is 250 mm.

     -----------------------------------------------------  ^
     |							 |  |
     |			Er				 |  |
     |							 |  |
     |		  -----------	    ----------- 	 |  H
     |		  <----w----><--s--><----w----> 	 |  |
     |							 |  |
     |							 |  |
     |							 |  |
     -----------------------------------------------------  v
     <-------------------------W------------------------->

     The program reports: H = 1.0, ; w = 1.44 ; s = 0.44 The height of the box H
     must be small compared to the length L, (perhaps no more  than  7%  of  the
     length), or 17.5 mm in this case, with a length of 250 mm, otherwise fring-
     ing  effects will be significant. The width of the structure W should be as
     large as possible. The program suggests making this 5*H+2*w+s. The  7%  and
     5*H+2*w+s	are  educated  guesses,  rather  than exact figures. There is no
     problem in making the width  larger than 5*H+2*w+s. The length  L	must  be
     kept at 250 mm. The RATIO of the dimensions H, w and s (but not L or W must
     be kept constant. W just needs to be sufficiently large - it is uncritical.

     If  you happened to have some 15 mm square brass available, then using that
     for the side-walls would require that H becomes 15*1.0 = 15 mm, w = 15*1.44
     = 21.6 mm	and s = 15*0.44 = 6.6 mm

     There is no need to compute the above scaling with a calculator,  as  using
     The  -H option allows one to specify the height H. The program then reports
     the exact dimensions for the length L, height H, w, s and suggests a  mini-
     mum width for W.

     In summary we have:
	 30 dB coupler +1.02 dB / -0.78 dB for 130 to 170 MHz
	 Length L = 250 mm, height H = 15 mm, stripline spacing s = 6.3 mm
	  stripline width w = 21.6 mm enclosure width W >= 124 mm

     By default, design_coupler prints a lot of information to the screen.  This
     can  be reduced by the -q option or reduced to only one line with -qq Other
     options include -Z to change the impedance from the default 50 Ohms and  -C
     to see the fully copyright, Licensing and distribution information

FILES
     No files are created at all.

SEE ALSO
     atlc(1)
     create_bmp_for_circ_in_circ(1)	 create_bmp_for_circ_in_rect(1)     cre-
     ate_bmp_for_microstrip_coupler(1)	create_bmp_for_rect_cen_in_rect(1)  cre-
     ate_bmp_for_rect_cen_in_rect_coupler(1) create_bmp_for_rect_in_circ(1) cre-
     ate_bmp_for_rect_in_rect(1)     create_bmp_for_stripline_coupler(1)    cre-
     ate_bmp_for_symmetrical_stripline(1)	 find_optimal_dimensions_for_mi-
     crostrip_coupler(1)
     readbin(1)

     http://atlc.sourceforge.net		- Home page
     http://sourceforge.net/projects/atlc	- Download area
     atlc-X.Y.Z/docs/html-docs/index.html	- HTML docs
     atlc-X.Y.Z/docs/qex-december-1996/design_coupler.pdf - theory paper
     atlc-X.Y.Z/examples			- examples

Dr. David Kirkby	    atlc-4.4.2 10th Sept 2003	       design_coupler(1)

home | help