home | help
find_optim...trp_coupler(1)  General Commands Manual find_optim...trp_coupler(1)

NAME
     find_optimal_dimensions_for_microstrp_coupler  part of atlc.

SYNOPSIS
     find_optimal_dimensions_for_microstrp_coupler  [options...  ] h t Er1 Er2 Z
     Zodd_req Zeve_reg outfile.bmp

WARNING
     This man page is not a complete set of documentation -  the  complexity  of
     the  atlc project makes man pages not an ideal way to document it, although
     out of completeness, man pages are produced.  The best  documentation  that
     was  current  at the time this version was produced should be found on your
     hard drive, usually at
     /usr/local/share/atlc/docs/html-docs/index.html
     although it might be elsewhere if your system administrator  chose  to  in-
     stall  the  package elsewhere. Sometimes, errors are corrected in the docu-
     mentation and placed at http://atlc.sourceforge.net/ before a  new  release
     of  atlc  is released.  Please, if you notice a problem with the documenta-
     tion - even spelling errors and typos, please let me know.

DESCRIPTION
     find_optimal_dimensions_for_microstrp_coupler is  part  of  the  atlc,  CAD
     package  for  the design and analysis of transmission lines and directional
     couplers. While the executable program atlc (as  opposed  to  the	complete
     package  atlc)  is  able to analyse the properties of directional couplers,
     telling you both the odd and even mode impedances Zodd and Zeven, it is not
     able to design a coupler to have specific odd and even mode impedances. The
     only way to use the program program atlc

     The parameters 'W' and 'H' and the inner dimensions of the outer conductor.
     The inner conductor has a diameter of 'd' and is offset from the centre  of
     the  outer conductor by an amount 'x' horizontally and 'y' vertically.  The
     space between the inner and outer conductors is a	dielectric  of	relative
     permittivity  'Er'.  If there is just a vacuum dielectric, then 'Er' should
     be set to 1.0

     find_optimal_dimensions_for_microstrp_coupler  d W H x y Er >  filename.bmp
     OR
     find_optimal_dimensions_for_microstrp_coupler -f filename.bmp d W H x y Er

     The  bitmaps  produced by find_optimal_dimensions_for_microstrp_coupler are
     24-bit bit colour bitmaps, as are required by atlc.

     The permittivities of the bitmap, set by 'Er', determine the colours in the
     bitmap. If Er1 is 1.0, 1.006, 2.1, 2.2, 2.33, 2.5, 3.3,  3.335,  3.7,  4.8,
     10.2  or 100 then the colour corresponding to that permittivity will be set
     according to the colours defined in COLOURS below. If  Er	is  not  one  of
     those  permittivities,  the  region  of  permittivity Er will be set to the
     colour 0xCAFF00. The program atlc does not know  what  these  permittivites
     are, so atlc, must be told with the -d command line option, as in example 4
     below.

OPTIONS
     -b bitmapsize
     is used to set the size of the bitmap, and so the accuracy to which atlc is
     able to calculate the transmission line's properties. The default value for
     'bitmapsize' is normally 4, although this is set at compile time. The value
     can be set anywhere from 1 to 15, but more than 8 is probably not sensible.

     -f outfile

     -v
     Causes  find_optimal_dimensions_for_microstrp_coupler to print some data to
     stderr. Note, nothing extra goes to standard output, as that is expected to
     be redirected to a bitmap file.

COLOURS
     The 24-bit bitmaps that atlc expects, have 8 bits assigned to represent the
     amount of red, 8 for blue and 8 for green. Hence there are  256  levels  of
     red, green and blue, making a total of 256*256*256=16777216 colours.  Every
     one  of the possible 16777216 colours can be defined precisely by the stat-
     ing the exact amount of red, green and blue, as in:

     red	 = 255,000,000 or 0xff0000
     green	 = 000,255,000 or 0x00ff00
     blue	 = 000,000,255 or 0x0000ff
     black	 = 000,000,000 or 0x000000
     white	 = 255,255,255 or 0xffffff
     Brown	 = 255,000,255 or 0xff00ff
     gray	 = 142,142,142 or 0x8e8e8e

     Some colours, such as pink, turquoise, sandy,  brown,  gray  etc  may  mean
     slightly different things to different people. This is not so with atlc, as
     the  program  expects  the  colours  below  to be EXACTLY defined as given.
     Whether you feel the colour is sandy or yellow is up to you, but if you use
     it in your bitmap, then it either needs to be a colour recognised by  atlc,
     or you must define it with a command line option (see OPTIONS and example 5
     below).
     The following conductors are recognised by atlc:
     red    = 255,000,000 or 0xff0000 is the live conductor.
     green  = 000,255,000 or 0x00ff00 is the grounded conductor.
     black  = 000,000,000 or 0x000000 is the negative conductor

     All  bitmaps  must  have the live (red) and grounded (green) conductor. The
     black conductor is not currently supported, but it will be used to indicate
     a negative conductor, which will be needed if/when  the  program  gets  ex-
     tended to analyse directional couplers.

     The  following  dielectrics  are  recognised by atlc and so are produced by
     find_optimal_dimensions_for_microstrp_coupler.

     white     255,255,255 or 0xFFFFFF as Er=1.0   (vacuum)
     white     255,202,202 or 0xFFCACA as Er=1.0006 (air)
     blue      000,000,255 or 0x0000FF as Er=2.1   (PTFE)
     Mid gray  142,242,142 or 0x8E8E8E as Er=2.2   (duroid 5880)
     mauve     255.000,255 or 0xFF00FF as Er=2.33  (polyethylene)
     yellow    255,255,000 or 0xFFFF00 as Er=2.5   (polystyrene)
     sandy     239,203,027 or 0xEFCC1A as Er=3.3   (PVC)
     brown     188,127,096 or 0xBC7F60 as Er=3.335 (epoxy resin)
     Turquoise 026,239,179 or 0x1AEFB3 as Er=4.8   (glass PCB)
     Dark gray 142,142,142 or ox696969 as Er=6.15  (duroid 6006)
     L. gray   240,240,240 or 0xDCDCDC as Er=10.2  (duroid 6010)
     D. Orange 213,160,077 or 0xD5A04D as Er=100   (for testing)
     If the permittivity is one not in the above list, then those parts  of  the
     image  with  Er1  will  be  set  to  0xCAFF00,  and those parts with Er2 to
     0xAC82AC.

EXAMPLES
     Here are a few  examples  of  the	use  of  find_optimal_dimensions_for_mi-
     crostrp_coupler. Again, see the html documentation in atlc-X.Y.Z/docs/html-
     docs for more examples.

     In the first example, there is just an air dielectric, so Er1=Er2=1.0.  The
     inner of 1x1 inches (or mm, miles etc) is placed centrally in an outer with
     dimensions 3 x 3 inches.

     The exact place where the dielectric starts (a) and its width (d) are unim-
     portant, but they must still be entered.

     % find_optimal_dimensions_for_microstrp_coupler 3 3 1 1 1 1 1 1 > ex1.bmp
     % atlc ex1.bmp

     In  this  second  example, an inner of 15.0 mm x 0.5 mm is surrounded by an
     outer with internal dimensions of 61.5 x 20.1 mm. There is a material  with
     permittivity  2.1	(Er  of PTFE) below the inner conductor. The output from
     find_optimal_dimensions_for_microstrp_coupler is sent to  a  file	ex1.bmp,
     which is then processed by atlc

     %	find_optimal_dimensions_for_microstrp_coupler 61.5 20.1 5 22 0.5 50 15 5
     1.0 2.1 > ex2.bmp
     % atlc ex2.bmp

     In example 3, the bitmap is made larger, to increase accuracy,  but  other-
     wise  this  is  identical	to  the  second  example.  % find_optimal_dimen-
     sions_for_microstrp_coupler -b7 61.5 20.1 5 22  0.5  50  15  5  1.0  2.1  >
     ex3.bmp
     % atlc ex3.bmp

     In   the	fourth	example,  instead  of  re-directing  find_optimal_dimen-
     sions_for_microstrp_coupler's output to a file with the > sign, it is  done
     using the -f option.
     %	find_optimal_dimensions_for_microstrp_coupler  -f ex4.bmp 61.5 20.1 5 22
     0.5 50 15 5 1.0 2.1
     % atlc ex4.bmp

     In the fifth example, materials with permittivites 2.78 and 7.89 are  used.
     While  there  is  no  change  in how to use find_optimal_dimensions_for_mi-
     crostrp_coupler, since these permittivities are not  known,  we  must  tell
     atlc  what they are.  % find_optimal_dimensions_for_microstrp_coupler 61 20
     1 4 22 0.5 50 15 5 2.78 7.89 > ex5.bmp % atlc -d CAFF00=2.78 -d AC82AC=7.89
     ex5.bmp In the sixth and final example, the -v option is used to print some
     extra data to stderr from find_optimal_dimensions_for_microstrp_coupler.

SEE ALSO
     atlc(1) create_bmp_for_circ_in_circ(1) create_bmp_for_circ_in_rect(1)  cre-
     ate_bmp_for_microstrip_coupler(1)	create_bmp_for_rect_cen_in_rect(1)  cre-
     ate_bmp_for_rect_cen_in_rect_coupler(1) create_bmp_for_rect_in_circ(1) cre-
     ate_bmp_for_rect_in_rect(1)    create_bmp_for_stripline_coupler(1)     cre-
     ate_bmp_for_symmetrical_stripline(1) design_coupler(1) readbin(1)

     http://atlc.sourceforge.net		- Home page
     http://sourceforge.net/projects/atlc	- Download area
     atlc-X.Y.Z/docs/html-docs/index.html	- HTML docs
     atlc-X.Y.Z/docs/qex-december-1996/atlc.pdf - theory paper
     atlc-X.Y.Z/examples			- examples

Dr. David Kirkby	    atlc-4.5.0 28th Sept 2003find_optim...trp_coupler(1)

home | help