FXLOAD(8) Linux Programmer's Manual FXLOAD(8) NAME fxload - Firmware download to EZ-USB devices SYNOPSIS fxload [ -v ] [ -l ] [ -B backend] [ -D devpath ] [ -I firmware ] [ -t type ] [ -c config ] [ -s loader ] fxload [ -D devpath ] [ -L link ] [ -m mode ] fxload [ -V ] DESCRIPTION fxload is a program which downloads firmware to USB devices based on An- chorChips EZ-USB, Cypress EZ-USB FX, or Cypress EZ-USB FX2/FX2LP/FX3 micro- controllers. These have 8-bit 8051 cores with special extensions for USB I/O. The FX2 supports high speed USB 2.0 transfers (480 Mbit/sec) as well as full speed USB 1.1 transfers (12 Mbit/sec), while the earlier parts sup- port only full speed transfers. The FX3 supports super speed USB 3.0 transfers and has a 32-bit ARM core. These controllers have several pack- age options, and can be set up with external memory (on-chip memory is usu- ally 8K or 16K; for FX3, it is 512K), EEPROMs, and ROMs when device costs allow. This uses "usbfs" (older name: "usbdevfs") to access devices, and issues vendor specific control requests to download and reset the EZ-USB devices. Normally, firmware will then "renumerate" by disconnecting from USB and then reconnecting as a new device. It then appears with new device de- scriptors and functionality, as provided by the firmware which has been downloaded. To support some non-firmware applications, this can also set up symbolic links for those usbfs names. It can also change their access modes. Both of these can help simplify software applications that need to talk to USB devices using user mode drivers, don't want to run with privileges or to examine all of the existing USB devices, and which don't need more kernel drivers. See the Linux-Hotplug web site for information about how to use fxload to download device firmware when hotplugging USB devices, using driver-spe- cific scripts stored in the /etc/hotplug/usb directory. FUNCTION LETTERS At least one of the following options must be specified. Note that as usual with UNIX and Linux commands, the order of command option flags does not matter. You may use these in any order. -I firmware Downloads the specified firmware file. For FX3 devices, the format is a Cypress-specific binary image. For other devices, the file has standard Intel hexfile format. (Common naming conventions include *.hex , *.ihx , and *.img). Depending on the device and firmware in use, the -s option may also be necessary to specify a second stage loader. Firmware is normally downloaded to RAM and executed, but there is also an option for downloading into bootable I2C EEPROMs. -L link Creates the specified symbolic link to the usbfs device path. This would typically be used to create a name in a directory that would be searched by an application. The symlink would be removed by some other component on device unplug. -m mode Changes permissions on the "usbfs" device node. By default, those nodes are only accessible by privileged users, which doesn't help when the user mode device driver needs to run without root privi- leges. Note that usbfs mount options like devmode=0666 are also available. -V Identifies the version of fxload being invoked, and exits without performing other actions. Note that when downloading firmware that renumerates, there's no point in changing the device permissions or creating a symbolic link. OPTIONS By default, fxload assumes the device uses an EZ-USB or EZ-USB FX. It also assumes that the device in question has been specified by USB kernel hot- plugging conventions, using the DEVICE environment variable to name a "us- bfs" file that can be used to talk to the device. -c config Indicates the specified firmware should be downloaded to an I2C boot EEPROM rather than to RAM. The parameter is the EZ-USB FX or FX2 configuration byte, and for AnchorChips devices the value should be zero. This requires a second stage loader (e.g. vend_ax.hex) that knows how to write to I2C EEPROMs specified using the -s option, as well as a device that's provided with an EEPROM large enough to store the boot firmware. After downloading to a device's EEPROM, you should retest it starting from power off. -s loader This identifies the file holding a second stage loader (in the same file format as the firmware itself), which is loaded into internal memory. This loader understands additional vendor control requests, beyond the one built into all EZ-USB hardware, which are needed to write external RAM or EEPROM. As a last step when loading firmware, fxload normally overwrites this second stage loader with parts of the firmware residing on-chip. -t type Indicates which type of microcontroller is used in the device; type may be one of an21 (the original AnchorChips devices), fx (Cypress' updated version, the EZ-USB FX), fx2 (the Cypress EZ-USB FX2, sup- porting high speed transfers), fx2lp (the Cypress EZ-USB FX2LP, with 16KB internal RAM), or fx3 (the Cypress EZ-USB FX3, supporting USB 3.0). Except when writing to EEPROM, all that normally matters when downloading firmware is whether or not the device uses an FX2 or FX3. -v Prints some diagnostics, such as download addresses and sizes, to standard error. Repeat the flag (-vv, -vvv) to get more diagnos- tics. -l print error and verbose messages to syslog. -D devpath Specifies the "usbfs" path name for the device in question, such as /proc/bus/usb/004/080. This takes precedence over any DEVICE envi- ronment variable that may be set. If libusb backend is used, you must provide a device IDs within a string of format 'vid=<VID>,pid=<PID>'. For example, for Xilinx JTAG USB cable you may want to pass "vid=0x03fd,pid=0x000d" as an argument. Longer version of syntax has been provided to prevent confusion, since in various systems vendor/product IDs are reported in different order. -B specifies the backend used to provide USB functionality for fxload . Possible values include "linux" and "libusb". On GNU/Linux systems, "linux" is the default and refers to Linux-only ioctl() interface. For "libusb", fxload must be compiled with LIBUSB_SUPPORT compile option. On systems different than GNU/Linux, "libusb" is always im- plied. See -D on how to pass a device specification for particular backends. NOTES This program implements one extension to the standard "hex file" format. Lines beginning with a "#" character are ignored, and may be used to hold copyright statements and other information. Other tools may not handle hexfiles using this extension. At this writing, "usbfs" is a kernel configuration option. That means that device drivers relying on user mode firmware downloading may need to depend on that kernel configuration option. A less preferable alternative in- volves compiling the firmware into the kernel and managing downloads and renumeration there. This is less preferable in part because much device firmware is provided with GPL-incompatible licensing, and in part because storing such firmware firmware wastes kernel memory. For EZ-USB family devices, the hardware's first stage loader (supporting the 0xA0 vendor request) can't write into external memory. Configurations that put firmware into external memory thus need a second stage loader. For typical "flat" memory architectures, a loader supporting the 0xA3 ven- dor request is used to write into that memory. Similarly, a second stage loader that supports the 0xA2 vendor request is needed when writing boot firmware into an I2C EEPROM. These 0xA2 and 0xA3 vendor commands are con- ventions defined by Cypress. Devices that use bank switching or similar mechanisms to stretch the 64KByte address space may need different ap- proaches to loading firmware. Not all devices support EEPROM updates. Some EZ-USB based devices don't have an I2C EEPROM; many such EEPROMs are too small to store firmware; and some firmware can't be placed in bootable I2C EEPROMs. ENVIRONMENT VARIABLES DEVICE normally names a "usbfs" file that will be used to talk to the de- vice. This is provided by the Linux kernel as part of USB hotplug- ging. FILES /usr/share/usb/a3load.hex Second stage loader that works with AnchorChips EZ-USB, Cypress EZ- USB FX, and Cypress EZ-USB FX2. Note that this only supports the 0xA3 vendor command, to write external memory. A loader that also supports the 0xA2 command, to write boot EEPROMs, is included with Cypress developer kits. SEE ALSO hotplug(8) AUTHORS Linux Hotplugging Project http://linux-hotplug.sourceforge.net/ April 2012 FXLOAD(8)
NAME | SYNOPSIS | DESCRIPTION | FUNCTION LETTERS | OPTIONS | NOTES | ENVIRONMENT VARIABLES | FILES | SEE ALSO | AUTHORS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=fxload&sektion=8&manpath=FreeBSD+Ports+15.1.quarterly>