FreeBSD Manual Pages
GDAL_MERGE(1) GDAL GDAL_MERGE(1) NAME gdal_merge - Mosaics a set of images. SYNOPSIS gdal_merge [--help] [--help-general] [-o <out_filename>] [-of <out_format>] [-co <NAME>=<VALUE>]... [-ps <pixelsize_x> <pixelsize_y>] [-tap] [-separate] [-q] [-v] [-pct] [-ul_lr <ulx> <uly> <lrx> <lry>] [-init "<value>[ <value>]..."] [-n <nodata_value>] [-a_nodata <output_nodata_value>] [-ot <datatype>] [-createonly] <input_file> [<input_file>]... DESCRIPTION This utility will automatically mosaic a set of images. All the images must be in the same coordinate system and have a matching number of bands, but they may be overlapping, and at different resolutions. In areas of overlap, the last image will be copied over earlier ones. Nodata/transparency values are considered on a band by band level, i.e. a nodata/transparent pixel on one source band will not set a nodata/transparent value on all bands for the target pixel in the resulting raster nor will it overwrite a valid pixel value. NOTE: gdal_merge is a Python utility, and is only available if GDAL Python bindings are available. --help Show this help message and exit --help-general Gives a brief usage message for the generic GDAL commandline options and exit. -o <out_filename> The name of the output file, which will be created if it does not already exist (defaults to "out.tif"). -of <format> Select the output format. Starting with GDAL 2.3, if not specified, the format is guessed from the extension (previously was GTiff). Use the short format name. -co <NAME>=<VALUE> Many formats have one or more optional creation options that can be used to control particulars about the file created. For instance, the GeoTIFF driver supports creation options to control compression, and whether the file should be tiled. The creation options available vary by format driver, and some sim- ple formats have no creation options at all. A list of options sup- ported for a format can be listed with the --format command line op- tion but the documentation for the format is the definitive source of information on driver creation options. See Raster drivers for- mat specific documentation for legal creation options for each for- mat. -ot <type> Force the output image bands to have a specific data type supported by the driver, which may be one of the following: Byte, Int8, UInt16, Int16, UInt32, Int32, UInt64, Int64, Float32, Float64, CInt16, CInt32, CFloat32 or CFloat64. -ps <pixelsize_x> <pixelsize_y> Pixel size to be used for the output file. If not specified the resolution of the first input file will be used. -tap (target aligned pixels) align the coordinates of the extent of the output file to the values of the -tr, such that the aligned extent includes the minimum extent. Alignment means that xmin / resx, ymin / resy, xmax / resx and ymax / resy are integer values. -ul_lr <ulx> <uly> <lrx> <lry> The extents of the output file. If not specified the aggregate ex- tents of all input files will be used. -q, -quiet Suppress progress messages. -v Generate verbose output of mosaicing operations as they are done. -separate Place each input file into a separate band. -pct Grab a pseudo-color table from the first input image, and use it for the output. Merging pseudo-colored images this way assumes that all input files use the same color table. -n <nodata_value> Ignore pixels from files being merged in with this pixel value. -a_nodata <output_nodata_value> Assign a specified nodata value to output bands. -init <"value(s)"> Pre-initialize the output image bands with these values. However, it is not marked as the nodata value in the output file. If only one value is given, the same value is used in all the bands. -createonly The output file is created (and potentially pre-initialized) but no input image data is copied into it. EXAMPLES Example 1: Creating an image with the pixels in all bands initialized to 255 gdal_merge -init 255 -o out.tif in1.tif in2.tif Example 2: Creating an RGB image that shows blue in pixels with no data gdal_merge -init "0 0 255" -o out.tif in1.tif in2.tif The first two bands will be initialized to 0 and the third band will be initialized to 255. Example 3: Passing a large list of files to gdal_merge ls -1 *.tif > tiff_list.txt A large list of files can be passed to gdal_merge by listing them in a text file using the command above on Linux, or: dir /b /s *.tif > tiff_list.txt on Windows. The text file can then be passed to gdal_merge using --optfile: gdal_merge -o mosaic.tif --optfile tiff_list.txt Example 4: Creating an RGB image by merging 3 different greyscale bands Conduct "merging by stacking" with the -separate flag. Given three greyscale files that cover the same area, you can run: gdal_merge -separate 1.tif 2.tif 3.tif -o rgb.tif This maps 1.tif to red, 2.tif to green and 3.tif to blue. Example 5: Specifying overlap precedence The last image in the input line comes out on top of the finished image stack. You might also need to use -n to note which value should not be copied into the destination image if it is not already defined as nodata. gdal_merge -o merge.tif -n 0 image1.tif image2.tif image3.tif image4.tif AUTHOR Frank Warmerdam <warmerdam@pobox.com>, Silke Reimer <silke@intevation.de> COPYRIGHT 1998-2025 Oct 29, 2025 GDAL_MERGE(1)
NAME | SYNOPSIS | DESCRIPTION | EXAMPLES | AUTHOR | COPYRIGHT
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=gdal_merge&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>