GNUNET-ARM(1) General Commands Manual GNUNET-ARM(1) NAME gnunet-arm -- control GNUnet services SYNOPSIS gnunet-arm [-c FILENAME | --config=FILENAME] [-d | --delete] [-e | --end] [-E | --no-stderr] [-h | --help] [-i SERVICE | --init=SERVICE] [-I | --info] [-k SERVICE | --kill=SERVICE] [-l FILENAME | --logfile=FILENAME] [-L LOGLEVEL | --loglevel=LOGLEVEL] [-m | --monitor] [-O | --no-stdout] [-q | --quiet] [-r | --restart] [-s | --start] [-T -DELAY | --timeout=TIMEOUT] [-v | --version] DESCRIPTION gnunet-arm can be used to start or stop GNUnet services, including the ARM service itself. The ARM service is a supervisor for GNUnet's service processes. ARM starts services on-demand or as configured and restarts them if they crash. -c FILENAME | --config=FILENAME Use the configuration file FILENAME. -d | --delete Delete configuration file and directory on exit. -e | --end Shutdown all GNUnet services (including ARM itself). Running "gnunet-arm -e" is the usual way to shutdown a GNUnet peer. -E | --no-stderr Don't let gnunet-arm inherit stderr (standard error). -h | --help Print short help on options. -i SERVICE | --init=SERVICE Starts the specified SERVICE if it is not already running. More specifically, this makes the service behave as if it were in the default services list. -I | --info List all running services. -k SERVICE | --kill=SERVICE Stop SERVICE if it is running. While this will kill the service right now, the service may be restarted immediately if other ser- vices depend on it (the service is then started 'on-demand'). If the service used to be a 'default' service, its default-service status will be revoked. If the service was not a default service, it will just be (temporarily) stopped, but could be re-started on- demand at any time. -l FILENAME | --logfile=FILENAME Write logs to FILENAME. -L LOGLEVEL | --loglevel=LOGLEVEL Use LOGLEVEL for logging. Valid values are DEBUG, INFO, WARNING and ERROR. -m | --monitor Monitor service activity of ARM. In this mode, the command will not terminate until the user presses CTRL-C (thus sending SIGTERM or SIGINT). -O | --no-stdout Don't let gnunet-arm inherit standard output -q | --quiet Don't print status messages. -r | --restart Stop and start all GNUnet default services. -s | --start Start all GNUnet default services on this system (and also ARM). Naturally, if a service is demanded by a default service, it will then also be started. Running "gnunet-arm -s" is the usual way to start a GNUnet peer. -T -DELAY | --timeout=DELAY Exit with error status if operation does not finish after DELAY, provided in number of microseconds. -v | --version Print GNUnet version number. EXAMPLES Start the gnunet-arm for the user: gnunet-arm -s Stop the gnunet-arm for the user: $ gnunet-arm -e SEE ALSO gnunet-config(1), gnunet-setup(1) The full documentation for gnunet is maintained as a Texinfo manual. If the info(1) and gnunet programs are properly installed at your site, the command info gnunet should give you access to the complete handbook, info gnunet-c-tutorial will give you access to a tutorial for developers. Depending on your installation, this information is also available in gnunet(7)and gnunet-c-tutorial(7). BUGS Report bugs by using https://bugs.gnunet.org or by sending electronic mail to <gnunet-developers@gnu.org>. FreeBSD ports 15.quarterly January 4, 2012 GNUNET-ARM(1)
NAME | SYNOPSIS | DESCRIPTION | EXAMPLES | SEE ALSO | BUGS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=gnunet-arm&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>