MCJOIN(1) General Commands Manual MCJOIN(1) NAME mcjoin -- tiny multicast testing tool SYNOPSIS mcjoin [-dhjosv] [-b BYTES] [-c COUNT] [-f MSEC] [-i IFNAME] [-l LEVEL] [-p PORT] [-t TTL] [-w SEC] [-W SEC] [[SOURCE,]GROUP0[:PORT] .. [SOURCE,]GROUPN[:PORT] | [SOURCE,]GROUP[:PORT]+NUM] DESCRIPTION mcjoin can be used to join IPv4 and IPv6 multicast groups, display progress as multicast packets are received, or sent when acting as sender, and also send multicast packets on select groups. Note: an IPv6 group with custom port must be written as [ADDR]:port, i.e., with enclosing brackets. mcjoin can help verify intended IGMP snooping functionality in layer-2 bridges (switches), as well as verify forwarding of multicast in static (SMCRoute) or dynamic (mrouted, pimd, pimd-dense, or pim6sd) multicast routing setups. mcjoin supports source-specific multicast, SSM (S,G), as well as any-source multicast, ASM (*,G). The source IP of an (S,G) pair is an optional argu- ment that must precede the group and be separated with a comma. No spaces are allowed between source and group in this form. Multiple (S,G) pairs are separated with space. mcjoin does not create or send IGMP or MLD frames directly. It only asks the underlying UNIX kernel for groups from a specific interface, which is then converted to the appropriate wire format by the kernel. This means, for instance, that if you want to create an IGMP v3 membership report on the wire that joins one group from multiple sources, you tell mcjoin to join two (S,G) pairs. The conversion to IGMP v3 report format is done by the kernel. On Linux systems you can change the IGMP version of an interface, and thus what type of packets the kernel generates, by writing to the file /proc/sys/net/ipv4/conf/eth0/force_igmp_version. E.g., to change eth0 to IGMPv2: echo 2 | sudo tee /proc/sys/net/ipv4/conf/eth0/force_igmp_version OPTIONS With no options given mcjoin acts as a multicast receiver (or sink), join- ing the default group 225.1.2.3, listening on the default interface, eth0, binding to the default port, 1234. Use the following options to adjust this behavior: -b BYTES Payload in bytes over IP/UDP header (42 bytes), default: 100 -c COUNT Stop sending/receiving after COUNT number of packets -d Run as a daemon in the background, detached from the current termi- nal. All output, except progress is sent to syslog(3) -f MSEC Frequency, poll/send every MSEC milliseconds, default: 100 -h Print a summary of the options and exit -i IFNAME Interface to use for sending/receiving multicast, default: eth0 -j Join groups, default unless acting as sender -l LEVEL Control mcjoin log level; none, notice, debug. Default: notice -o Old (plain/ordinary/original) output, no fancy progress bars -p PORT UDP port number to send/listen to, default: 1234 -s Act as sender, sends packets to select groups, 1/100 msec, default: no -t TTL TTL to use when sending multicast packets, default: 1 -v Show version information -w SEC Initial wait, sleep SEC seconds before starting anything. Useful for scripting test systems that launch mcjoin at boot without sync- ing with networking bring-up -W SEC Timeout, in seconds, before mcjoin exits, regardless of how many packets have been received. With this option mcjoin exit either after SEC seconds, or after COUNT packets have been received USAGE To verify multicast connectivity, the simplest way is to run mcjoin on one system, without arguments, and on the other with the command option -s. In this setup one system joins the group 225.1.2.3 waiting for packets to ar- rive, and the other end starts sending packets to the same group. To ver- ify routing of multicast, make sure to add the -t TTL option to the sender since the default TTL is 1 and every router (simplified) decrements the TTL. For a more advanced example, say you want to verify that your topology can forward 20 consecutive groups in the MCAST_TEST_NET, as defined in RFC5771. Simply add the following as a standalone argument to both the receiver and the sender: 233.252.0.1+20 For non-consecutive groups, simply add them in any order you want, up to 250 groups are supported: 225.1.2.3 226.3.2.1+12 225.3.2.42 232.43.211.234 To run mcjoin as both a sender and a receiver on the same host you will likely need to employ something like network namespaces (Linux netns) for at least one of them. Otherwise the network stack will likely let the sender's data stream take a short cut to the receiver, without passing through an actual wire. Also, like most network applications, to run properly mcjoin needs both the loopback (lo) interface and a default route set up. At least in the de- fault (receiver) case. In a network namespace neither of these are set up by default. INTERACTIVE mcjoin can be controlled at runtime with the following keys: d Toggle frame duplication h Toggle help text l Toggle debug log q Quit mcjoin t Toggle viewing modes PgUp Scroll log view up PgDn Scroll log view down Ctrl-L Refresh display Ctrl-C Quit mcjoin SEE ALSO ping(1), mgen(1), nemesis(1) BUGS Use the project's GitHub page to file bug reports, feature requests or patches (preferably as GitHub pull requests), or questions at <https://github.com/troglobit/mcjoin> AUTHORS Originally based on an example by David Stevens, further developed and maintained by Joachim Wiberg at GitHub. FreeBSD ports 15.quarterly January 14, 2021 MCJOIN(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | USAGE | INTERACTIVE | SEE ALSO | BUGS | AUTHORS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=mcjoin&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>