FreeBSD Manual Pages
MTX(1) General Commands Manual MTX(1) NAME mtx - control SCSI media changer devices SYNOPSIS mtx [-f <scsi-generic-device>] [nobarcode] [invert] [noattach] command [ command ... ] DESCRIPTION The mtx command controls single or multi-drive SCSI media changers such as tape changers, autoloaders, tape libraries, or optical media jukeboxes. It can also be used with media changers that use the 'ATTACHED' API, presuming that they properly report the MChanger bit as required by the SCSI T-10 SMC specification. OPTIONS The first argument, given following -f , is the SCSI generic device corre- sponding to your media changer. Consult your operating system's documenta- tion for more information (for example, under Linux these are generally /dev/sg0 through /dev/sg15, under FreeBSD these are /dev/pass0 through /dev/passX, under SunOS it may be a file under /dev/rdsk). The 'invert' option will invert (flip) the media (for optical jukeboxes that allow such) before inserting it into the drive or returning it to the storage slot. The 'noattach' option forces the regular media changer API even if the me- dia changer incorrectly reported that it uses the 'ATTACHED' API. The 'nobarcode' option forces the loader to not request barcodes even if the loader is capable of reporting them. Following these options there may follow one or more robotics control com- mands. Note that the 'invert' and 'noattach' options apply to ALL of robot- ics control commands. COMMANDS --version Report the mtx version number (e.g. mtx 1.2.8) and exit. inquiry Report the product type (Medium Changer, Tape Drive, etc.), Ven- dor ID, Product ID, Revision, and whether this uses the Attached Changer API (some tape drives use this rather than reporting a Medium Changer on a separate LUN or SCSI address). noattach Make further commands use the regular media changer API rather than the _ATTACHED API, no matter what the "Attached" bit said in the Inquiry info. Needed with some brain-dead changers that re- port Attached bit but don't respond to _ATTACHED API. inventory Makes the robot arm go and check what elements are in the slots. This is needed for a few libraries like the Breece Hill ones that do not automatically check the tape inventory at system startup. status Reports how many drives and storage elements are contained in the device. For each drive, reports whether it has media loaded in it, and if so, from which storage slot the media originated. For each storage slot, reports whether it is empty or full, and if the media changer has a bar code, MIC reader, or some other way of uniquely identifying media without loading it into a drive, this reports the volume tag and/or alternate volume tag for each piece of media. For historical reasons drives are numbered from 0 and storage slots are numbered from 1. load <slotnum> [ <drivenum> ] Load media from slot <slotnum> into drive <drivenum>. Drive 0 is assumed if the drive number is omitted. unload [<slotnum>] [ <drivenum> ] Unloads media from drive <drivenum> into slot <slotnum>. If <dri- venum> is omitted, defaults to drive 0 (as do all commands). If <slotnum> is omitted, defaults to the slot that the drive was loaded from. Note that there's currently no way to say 'unload drive 1's media to the slot it came from', other than to explic- itly use that slot number as the destination. [eepos <operation>] transfer <slotnum> <slotnum> Transfers media from one slot to another, assuming that your mechanism is capable of doing so. Usually used to move media to/from an import/export port. 'eepos' is used to extend/retract the import/export tray on certain mid-range to high end tape li- braries (if, e.g., the tray was slot 32, you might say say 'eepos 1 transfer 32 32' to extend the tray). Valid values for eepos <operation> are 0 (do nothing to the import/export tray), 1, and 2 (what 1 and 2 do varies depending upon the library, consult your library's SCSI-level documentation). [eepos <operation>] [invert] [invert2] exchange <slotnum> <slotnum> [<slot- num>] Move medium from the first slot to the second slot, placing the medium currently in the second slot either back into the first slot or into the optional third slot. first [<drivenum>] Loads drive <drivenum> from the first slot in the media changer. Unloads the drive if there is already media in it (note: you may need to eject the tape using your OS's tape control commands first). Note that this command may not be what you want on large tape libraries -- e.g. on Exabyte 220, the first slot is usually a cleaning tape. If <drivenum> is omitted, defaults to first drive. last [<drivenum>] Loads drive <drivenum> from the last slot in the media changer. Unloads the drive if there is already a tape in it. (Note: you may need to eject the tape using your OS's tape control commands first). next [<drivenum>] Unloads the drive and loads the next tape in sequence. If the drive was empty, loads the first tape into the drive. position <slotnum> Positions the robot at a specific slot. Needed by some changers to move to and open the import/export, or mailbox, slot. AUTHORS The original 'mtx' program was written by Leonard Zubkoff and extensively revised for large multi-drive libraries with bar code readers by Eric Lee Green <eric@badtux.org>. See 'mtx.c' for other contributors. BUGS AND LIMITATIONS You may need to do a 'mt offline' on the tape drive to eject the tape be- fore you can issue the 'mtx unload' command. The Exabyte EZ-17 and 220 in particular will happily sit there snapping the robot arm's claws around thin air trying to grab a tape that's not there. For some Linux distributions, you may need to re-compile the kernel to scan SCSI LUN's in order to detect the media changer. Check /proc/scsi/scsi to see what's going on. If you try to unload a tape to its 'source' slot, and said slot is full, it will instead put the tape into the first empty slot. Unfortunately the list of empty slots is not updated between commands on the command line, so if you try to unload another drive to a full 'source' slot during the same in- vocation of 'mtx', it will try to unload to the same (no longer empty) slot and will urp with a SCSI error. This program reads the Mode Sense Element Address Assignment Page (SCSI) and requests data on all available elements. For larger libraries (more than a couple dozen elements) this sets a big Allocation_Size in the SCSI command block for the REQUEST_ELEMENT_STATUS command in order to be able to read the entire result of a big tape library. Some operating systems may not be able to handle this. Versions of Linux earlier than 2.2.6, in par- ticular, may fail this request due to inability to find contiguous pages of memory for the SCSI transfer (later versions of Linux 'sg' device do scat- ter-gather so that this should no longer be a problem). The eepos command remains in effect for all further commands on a command line. Thus you might want to follow eepos 1 transfer 32 32 with eepos 0 as the next command (which clears the eepos bits). Need a better name for 'eepos' command! ('eepos' is the name of the bit field in the actual low-level SCSI command, and has nothing to do with what it does). This program has only been tested on Linux with a limited number of tape loaders (a dual-drive Exabyte 220 tape library, with bar-code reader and 21 slots, an Exabyte EZ-17 7-slot autoloader, and a Seagate DDS-4 autochanger with 6 slots). It may not work on other operating systems with larger li- braries, due to the big SCSI request size. Please see the projecdt page http://sourceforge.net/projects/mtx for information on reporting bugs, re- questing features and the mailing list for peer support. HINTS Under Linux, cat /proc/scsi/scsi will tell you what SCSI devices you have. You can then refer to them as /dev/sga, /dev/sgb, etc. by the order they are reported. Under FreeBSD, camcontrol devlist will tell you what SCSI devices you have, along with which pass device controls them. Under Solaris, set up your 'sgen' driver so that it'll look for tape chang- ers (see /kernel/drv/sgen.conf and the sgen man page), type touch /recon- figure then reboot. You can find your changer in /devices by typing /usr/sbin/devfsadm -C to clean out no-longer-extant entries in your /de- vices directory, then find /devices -name \*changer -print to find the de- vice name. Set the symbolic link /dev/changer to point to that device name (if it is not doing so already). With BRU, set your mount and unmount commands as described on the BRU web site at http://www.bru.com to move to the next tape when backing up or restoring. With GNU tar, see mtx.doc for an example of how to use tar and mtx to make multi-tape backups. AVAILABILITY This version of mtx is currently being maintained by Robert Nelson <robert- nelson@users.sourceforge.net> . The 'mtx' home page is http://mtx.source- forge.net and the actual code is currently available there and via SVN from http://sourceforge.net/projects/mtx. SEE ALSO mt(1),loaderinfo(1),tapeinfo(1),scsitape(1),scsieject(1) MTX1.3 MTX(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | COMMANDS | AUTHORS | BUGS AND LIMITATIONS | HINTS | AVAILABILITY | SEE ALSO
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=mtx&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>