FreeBSD Manual Pages
podman-auto-update(1) General Commands Manual podman-auto-update(1) NAME podman-auto-update - Auto update containers according to their auto-update policy SYNOPSIS podman auto-update [options] DESCRIPTION podman auto-update pulls down new container images and restarts containers configured for auto updates. To make use of auto updates, the container or Kubernetes workloads must run inside a systemd unit. After a successful update of an image, the containers using the image get updated by restart- ing the systemd units they run in. Please refer to podman-systemd.unit(5) on how to run Podman under systemd. To configure a container for auto updates, it must be created with the io.containers.autoupdate label or the AutoUpdate field in podman-sys- temd.unit(5) with one of the following two values: * registry: If the label is present and set to registry, Podman reaches out to the corresponding registry to check if the image has been updated. The label image is an alternative to registry maintained for backwards compatibility. An image is considered updated if the digest in the local storage is different than the one of the remote image. If an image must be updated, Podman pulls it down and restarts the systemd unit executing the container. The registry policy requires a fully-qualified image ref- erence (e.g., quay.io/podman/stable:latest) to be used to create the con- tainer. This enforcement is necessary to know which image to actually check and pull. If an image ID was used, Podman would not know which im- age to check/pull anymore. * local: If the autoupdate label is set to local, Podman compares the image digest of the container to the one in the local container storage. If they differ, the local image is considered to be newer and the systemd unit gets restarted. Auto Updates and Kubernetes YAML Podman supports auto updates for Kubernetes workloads. The auto-update policy can be configured directly via podman-systemd.unit(5) or inside the Kubernetes YAML with the Podman-specific annotations mentioned below: * io.containers.autoupdate: "registry|local" to apply the auto-update pol- icy to all containers * io.containers.autoupdate/$container: "registry|local" to apply the auto- update policy to $container only * io.containers.sdnotify: "conmon|container" to apply the sdnotify policy to all containers * io.containers.sdnotify/$container: "conmon|container" to apply the sdno- tify policy to $container only By default, the autoupdate policy is set to "disabled", the sdnotify policy is set to "conmon". Systemd Unit and Timer Podman ships with a podman-auto-update.service systemd unit. This unit is triggered daily at midnight by the podman-auto-update.timer systemd timer. The timer can be altered for custom time-based updates if desired. The unit can further be invoked by other systemd units (e.g., via the depen- dency tree) or manually via systemctl start podman-auto-update.service. OPTIONS --authfile=path Path of the authentication file. Default is ${XDG_RUNTIME_DIR}/contain- ers/auth.json on Linux, and $HOME/.config/containers/auth.json on Win- dows/macOS. The file is created by podman login. If the authorization state is not found there, $HOME/.docker/config.json is checked, which is set using docker login. Note: There is also the option to override the default path of the authen- tication file by setting the REGISTRY_AUTH_FILE environment variable. This can be done with export REGISTRY_AUTH_FILE=path. Alternatively, the io.containers.autoupdate.authfile container label can be configured. In that case, Podman will use the specified label's value in- stead. --dry-run Check for the availability of new images but do not perform any pull opera- tion or restart any service or container. The UPDATED field indicates the availability of a new image with "pending". --format=format Change the default output format. This can be of a supported type like 'json' or a Go template. Valid placeholders for the Go template are listed below: +----------------+------------------------------+ | Placeholder | Description | +----------------+------------------------------+ | .Container | ID and name of the container | +----------------+------------------------------+ | .ContainerID | ID of the container | +----------------+------------------------------+ | .ContainerName | Name of the container | +----------------+------------------------------+ | .Image | Name of the image | +----------------+------------------------------+ | .Policy | Auto-update policy of the | | | container | +----------------+------------------------------+ | .Unit | Name of the systemd unit | +----------------+------------------------------+ | .Updated | Update status: | | | true,false,failed,pending | +----------------+------------------------------+ --rollback If restarting a systemd unit after updating the image has failed, rollback to using the previous image and restart the unit another time. Default is true. Note that detecting if a systemd unit has failed is best done by the con- tainer sending the READY message via SDNOTIFY. This way, restarting the unit waits until having received the message or a timeout kicked in. With- out that, restarting the systemd unit may succeed even if the container has failed shortly after. For a container to send the READY message via SDNOTIFY it must be created with the --sdnotify=container option (see podman-run(1)). The application running inside the container can then execute systemd-notify --ready when ready or use the sdnotify bindings of the specific programming language (e.g., sd_notify(3)). --tls-verify Require HTTPS and verify certificates when contacting registries (default: true). If explicitly set to true, TLS verification is used. If set to false, TLS verification is not used. If not specified, TLS verification is used unless the target registry is listed as an insecure registry in con- tainers-registries.conf(5) EXAMPLES Create a Quadlet file configured for auto updates: $ cat ~/.config/containers/systemd/sleep.container [Container] Image=registry.fedoraproject.org/fedora:latest Exec=sleep infinity AutoUpdate=registry Generate a systemd service from the Quadlet file by reloading the systemd user daemon: $ systemctl --user daemon-reload Start the systemd service and make sure the container is running $ systemctl --user start sleep.service $ podman ps CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAMES f8e4759798d4 registry.fedoraproject.org/fedora:latest sleep infinity 2 seconds ago Up 2 seconds systemd-sleep Check if a new image is available via --dry-run: $ podman auto-update --dry-run --format "{{.Image}} {{.Updated}}" registry.fedoraproject.org/fedora:latest pending Update the service: $ podman auto-update UNIT CONTAINER IMAGE POLICY UPDATED sleep.service f8e4759798d4 (systemd-sleep) registry.fedoraproject.org/fedora:latest registry true SEE ALSO podman(1), podman-generate-systemd(1), podman-run(1), podman-sys- temd.unit(5), sd_notify(3), systemd.unit(5) podman-auto-update(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | EXAMPLES | SEE ALSO
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=podman-auto-update&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>