ZITA-NJBRIDGE(1) General Commands Manual ZITA-NJBRIDGE(1) NAME zita-j2n, zita-n2j - Jack clients to transport multichannel audio over a local network. SYNOPSIS zita-j2n [ options ] ip-address ip-port zita-n2j [ options ] ip-address ip-port zita-j2n [ options ] ip-address ip-port interface zita-n2j [ options ] ip-address ip-port interface DESCRIPTION General The zita-j2n (sender) and zita-n2j (receiver) applications allow to ex- change up to 64 channels of full-quality uncompressed audio streams between two or more systems running the Jack audio server. Sender and receiver(s) can each have their own sample rate and period size, and no word clock sync between them is assumed. The receiver uses adaptive resampling to convert the audio stream(s) to its local sample rate. There is no master/slave relationship between sender and receiver(s). This is an explicit design goal. In all respects the net result of using zita- njbridge is similar to having analog audio connections between the sound cards of the systems using it. Nothing a sender can do will affect the re- ceiver(s), apart from the audio signals being available or reverting to si- lence if there is no sender. Xruns or skipped cycles will not affect the synchronisation or resampling. Jack freewheeling on either end will tem- porarily suspend operation. Zita-njbridge can be used in two ways: one-to-one, or one-to-many. Both IPv4 and IPv6 are supported. For a one-to-one setup the first form of the commands shown above should be used. The protocol used is UDP and the ip-address argument required for both sender and receiver is that of the receiver. A host name can be used instead of a numerical IP adresses, this will be looked up using getad- drinfo(). For a one-to-many setup the second form must be used The ip-address argu- ment should be a valid multicast address, and the mandatory interface argu- ment selects the network interface to be used. Resampler filter length. The receiver uses the zita-resampler library to resample signals to its lo- cal rate. The length of the multiphase low-pass filter used as part of the resampling algorithm determines the audio bandwidth, and adds to latency. It can also have a significant impact on CPU load if many channels are re- ceived. Zita-njbridge will select a filter length based on the lower of the sender and receiver sample rates. For sample rates of 44.1 Khz and above the value chosen will result in an attenuation of no more than 0.1 dB up to 20 kHz. The --filt option allows to override the automatic configuration, but this will normally not be necessary. Latency issues. When connecting two Jack systems with unsynchronised periods the minimum additional latency under worst case conditions is the sum of the two period times. Additional latency means any latency required to make the connection work without interruption. The round-trip latency from an ideal (zero ex- cess latency) analog input on the sender to an ideal (idem) analog output on the receiver will be twice this value. Worst case conditions means that the both sender and receiver can run at arbitrary times within their re- spective periods. Zita-njbridge is designed to provide a defined and constant additional la- tency. The target value is the sum of the two periods, plus resampling de- lay, plus any extra buffering specified by the user. The actual latency will be this value plus the average network delay. The latter is unknown so there is no way to compensate for it. This would be possible using either a return channel, or some way to sync clocks on the two systems which could then be used to measure the average network delay. The current release of zita-njbridge does not provide this as it is meant for use on a local net- work. A dedicated or lightly loaded gigabit Ethernet can provide typical network delays well below a millisecond. The --buff option of zita-n2j adds the specified number of milliseconds to the target latency. The default value is 10 ms which is more than enough on a moderately loaded Gigabit local network. This can be set to zero, for ex- ample when it is known that the sender will always run near the start of its Jack period and the network delay jitter is less than this period. If there is any network delay jitter above 10ms, increasing the extra buffer time will be necessary to avoid occasional interruption of the re- ceived audio streams. The latency does not depend on the when exactly the sender runs within its Jack period. This is similar to playback to a soundcard: when the playback samples are written well before they are due this does not decrease the la- tency, the data is just buffered until the end of the period. In the case of zita-njbridge the remaining time is available for network delay. This is why, when the sender is only lightly loaded and network delay is small, it is possible to use --buff 0 at the receivers. Use on wide area or wireless networks. The current implementation is designed to be used on local networks that provide more or less reliable delivery of packets, with low or moderate de- lay. Occasional lost packets will not impact the synchronisation or resam- pling, but any samples arriving out of order will be ignored (they will have been replaced by silence before). Extra buffering (using the --buff option) will allow an uninterrupted signal in the presence of delay jitter, at the price of additional latency. Zita-njbridge may be usable on long distance internet connections, but keep in mind it was not designed for this. Performance on wireless networks is purely a matter of chance. Again zita- njbridge is not designed for such use. OPTIONS Common options --help Print command line and options summary. --jname name Select the Jack client client name. Default is 'zita-j2n' or 'zita- n2j'. --jserv server Select the Jack server to connect to. --ipv4 --ipv6 Use only the specified IP address type. zita-j2n options --chan channels The number of channels to transmit, the default is 2 channels. --16bit Send audio as 16-bit signed integer samples. --24bit Send audio as 24-bit signed integer samples. This is the default format. --float Send audio as 32-bit floating point samples (Jack's internal for- mat). --mtu MTU Inform zita-j2n of the path MTU, allowing it to use packets up to that size. The default value is 1500. Note that large MTU values on a shared network may increase network delay jitter. --hops hops Set the maximum number of hops for multicast packets. Defaults to one, i.e. multicast is to the local net only. zita-n2j options --chan list A list of channels numbers in ascending order and separated by comma or dash characters, the latter indicating a range. Channel numbers start at 1. Only the requested channels will be resampled and have a corresponding Jack port. Channels not provided by the sender will output silence. The default channel list is '1,2'. --buff time Increase the target latency by the given time, in milliseconds. The default is 10 ms. See the description above for what exactly this means. --filt delay Set the resampler filter delay, in samples at the lower of the two sample rates, in the range 16..96. See above for details. --info Print additional diagnostic information. Four values will be printed four times per second: the number of jack periods during the last 1/4 second, the average resampler control loop error in frames, the average resampler ratio correction and the minumum number of frames available in the receive buffer. AUTHOR zita-j2n, zita-n2j and this manual page were written by Fons Adriaensen <fons@linuxaudio.org>. July 2014 ZITA-NJBRIDGE(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | AUTHOR
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=zita-j2n&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>