FreeBSD Manual Pages
ENCAPSULATE(1) General Commands Manual ENCAPSULATE(1) NAME encapsulate - multiplex several channels over a single socket with sam- pling of remote process exit status, and provide conversation termina- tion without closing the socket. netpipes 4.2 SYNOPSIS encapsulate --fd n [ --verbose ] [ --subproc [ --infd n[=sid] ] [ --outfd n[=sid] ] [ --duplex n[=sid] ] [ --Duplex n[=sid] ] [ --DUPLEX n[=sid] ] [ --prefer-local ] [ --prefer-remote ] [ --local-only ] [ --remote-only ] ] [ --client ] [ --server ] -[#n][v][s[in][on][dn][ion][oin][l][r][L][R]] command args ... DESCRIPTION encapsulate implements the Session Control Protocol (SCP) in a limited manner. encapsulate multiplexes several virtual channels over a single socket using SCP. encapsulate transmits the exit status of the local program to the remote end over a reserved SCP channel and receives the remote exit status back. encapsulate provides conversation boundaries without closing the socket. Flags may appear in any order. The first argument that isn't a flag is the command to spawn (assuming --subproc is specified, an error other- wise). OPTIONS --fd n, -#n : specify the file descriptor of the socket we will be mul- tiplexing subprocess channels over. This argument is required --verbose, -v : Print extra information (including a copyright notice) to stderr. --subproc, -s : spawn a subprocess. You must supply a command and args. If you omit this flag, then you must not supply a command and args. If you omit this flag, encapsulate will copy input from stdin to an outgoing channel in the SCP-muxed socket and copy to stdout from an incoming channel in the SCP-muxed socket. If you omit this flag, all of the input and output channel flags are illegal. --infd n, -in : specify an input channel. If there is a subprocess, it will be able to read from descriptor n. If there is no subprocess en- capsulate will read from its descriptor n (these are opposite polari- ties for the SCP channel). --outfd n, -on : specify an output channel. If there is a subprocess, it will be able to write to descriptor n. If there is no subprocess encapsulate will write to its descriptor n (these are opposite polari- ties for the SCP channel). --duplex n, -ion : specify a bidirectional channel. The remote encap- sulate will send the SCP SYN packet, and the local will respond with a SYN for the same session. The subprocess will be able to read and write to file descriptor n. The subprocess should use the sockdown(1) program if it must close one direction while leaving the other direc- tion open. --Duplex n, -dn : specify a bidirectional channel. The --client end of the encapsulate connection sends the SCP SYN packet and --server re- sponds with a SYN for the same session. The subprocess will be able to read and write to file descriptor n. The subprocess should use the sockdown(1) program if it must close one direction while leaving the other direction open. --DUPLEX n, -oin : specify a bidirectional channel. The local encapsu- late will send the SCP SYN packet, and the remote will respond with a SYN for the same session. The subprocess will be able to read and write to file descriptor n. The subprocess should use the sockdown(1) program if it must close one direction while leaving the other direc- tion open. All of the long forms of the bidirectional channel have an optional =sid component that can be used to specify the SCP Session ID. This is not very useful when connecting encapsulate to another instance of it- self, but could be handy when connecting to another piece of software that implements SCP. --prefer-local, -l : if both the remote and local subprocesses exit with non-zero (erroneous) codes, encapsulate will exit with the same code as the local subprocess. This is the default. --prefer-remote, -r : if both the remote and local subprocesses exit with non-zero (erroneous) codes, encapsulate will exit with the same code as the remote subprocess. --local-only, -L : encapsulate exits with the local status and ignores the remote status. --remote-only, -R : encapsulate exits with the remote status and ig- nores the local status. SESSION IDs AND SUBPROCESS CHANNELS When specifying channels for the subprocess, the order of the flags is very important. Every flag to the local encapsulate must have a corre- sponding flag on the remote encapsulate that is in the exact same posi- tion (in the list of channels). The descriptor numbers need not corre- spond, but the position and type of each channel must. A lamentably complicating factor is that the data flow implied by --infd and --outfd are different when you specify a subprocess. Local Remote --infd w/subproc --outfd w/subproc --infd w/subproc --infd --infd --infd w/subproc --infd --outfd --outfd w/subproc --infd w/subproc --outfd w/subproc --outfd --outfd --outfd w/subproc --outfd --infd --duplex --DUPLEX --Duplex --Duplex --DUPLEX --duplex RIGHT: l$ encapsulate --infd 0 --duplex 5 r$ encapsulate --outfd 1 --DUPLEX 5 WRONG: l$ encapsulate --infd 0 --duplex 5 r$ encapsulate --outfd 1 --duplex 5 --duplex must have a corresponding --DUPLEX on the remote end. l$ encapsulate --infd 0 --duplex 5 r$ encapsulate --DUPLEX 5 --outfd 1 --infd must have a corresponding --outfd on the remote end. It's out of order and the channels will be allocated incorrectly leading to pro- tocol errors. If you understand the source code for encapsulate, you can violate these guidelines, but it is unnecessary, error-prone, and ill-advised; besides, you don't really understand the source code. Don't do it. CLIENT -VS- SERVER The SCP has an implicit polarity. One end is the server and the other end is the client. You can specify which end is which using --client and --server. If you do not specify one, then encapsulate will compare the addresses of both ends of the socket (specified with --fd) and use a deterministic algorithm to pick one to be the server and one to be the client. If the remote address of the socket does not correspond to the remote encapsulate (e.g. the packets are being forwarded through a plugged gateway, the addresses are being masqueraded, or are otherwise percieved inconsistently by the two ends) then this algorithm has a good chance of "failing" and assigning both to be server or both to be client. The only time you should ever let encapsulate choose between client and server is in interactive situations. It is very likely that a software system built around encapsulate will be reused in a situation where the automatic polarity assignment fails. EXAMPLES Here's a simple file transfer daemon: server$ faucet 3001 --once --fd3 \ sh -c 'while ~/src/netpipes4.0/encapsulate --fd 3 -so5i4 \ sh -c "fname=`cat 0<&4`; echo \$fname; cat < \$fname 1>&5"; \ do true; done' client$ hose server 3001 --retry 10 --delay 1 --fd3 \ sh -c 'while read fname; do \ ~/src/netpipes4.0/encapsulate --fd 3 -si4o5 \ sh -c "echo $fname 1>&5; exec 5>&-; cat 0<&4" \ || break; done' Just type the name of the file you want to retrieve into the hose and press return. It will be dumped to stdout. Repeat until enlightened or bored. TROUBLESHOOTING Did you specify --client and --server properly? One side should be server, the other side should be client. If you specify them both as server or both as client, you have made a mistake. Do not rely on the automatic polarity detection. While it is theoretically a very good algorithm, it is fooled very easily. Do all of your channel assignments (--infd et al) match up? If you get these wrong, encapsulate will freak out and drip spooge all over your shoes. For deadlock avoidance, make sure you are closing channels when you don't need them anymore. Use the >&- redirection operator in sh or bash. Make sure you close it in all of the background processes as well. Unable to read stdin from a process that has been backgrounded with & ? Bash closes file descriptor 0 for any subprocess that is backgrounded (e.g. (command&) ). You can get around this by copying 0 onto another descriptor, and then copying it back within the backgrounded process. ( ( cat 0<&3 ) & ) 3<&0 SEE ALSO netpipes (1), http://sunsite.unc.edu/ses/scp.html The Session Control Protocol document on SunSite was a draft. There is a more recent one that doesn't specify header compression (which I don't use anyway). It may eventually become an RFC. Then again, en- capsulate may be the only program which ever implements SCP. BUGS encapsulate is not hard to deadlock. Until I add unbounded buffering inside encapsulate, avoid constructing deadlock-vulnerable systems. The encapsulate included with netpipes 4.0 totally failed to handle the case where no subprocess was specified. No error message would be is- sued, and the program would do absolutely nothing. The 4.1 version should work. encapsulate has no other known bugs. I'm sure there are unknown ones because this software is not yet mature; in fact, it's totally wet be- hind the ears. Break it and send me the pieces. Well, the command-line argument style is inconsistent with faucet & hose. I'll be updating faucet & hose. The Linux kernel from the beginning of time up through version 2.0.29 has a problem with sockets being shut down "too fast". This results in loss of data at the end of a stream and an "Error: connection reset by peer" during reads. 2.0.30 supposedly fixes this. This state machine flaw is very likely present in many other OSes, because the strange conditions that exercise it are almost nonexistent in normal applica- tions, but happen all the time in some applications of the NetPipes package. encapsulate can be used to work around this bug in some cases because encapsulate does not perform a shutdown on the network socket ever (it doesn't even do a "close"). CREDITS Hi Mom! Hi Dad! COPYRIGHT Copyright (C) 1997-98 Robert Forsman This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MER- CHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. AUTHOR Robert Forsman thoth@purplefrog.com Purple Frog Software http://web.purplefrog.com/~thoth/ June 19, 1997 ENCAPSULATE(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | SESSION IDs AND SUBPROCESS CHANNELS | CLIENT -VS- SERVER | EXAMPLES | TROUBLESHOOTING | SEE ALSO | BUGS | CREDITS | COPYRIGHT | AUTHOR
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=encapsulate&sektion=1&manpath=FreeBSD+Ports+15.0>