FreeBSD Manual Pages
MUNIN-N...NFIGURE(1) User Contributed Perl Documentation MUNIN-N...NFIGURE(1) NAME munin-node-configure - View and modify which plugins are enabled. SYNOPSIS munin-node-configure [options] DESCRIPTION munin-node-configure reports which plugins are enabled on the current node, and suggest changes to this list. By default this program shows which plugins are activated on the system. If you specify "--suggest", it will present a table of plugins that will probably work (according to the plugins' autoconf command). If you specify "--snmp", followed by a list of hosts, it will present a ta- ble of SNMP plugins that they support. If you additionally specify "--shell", shell commands to install those same plugins will be printed. These can be reviewed or piped directly into a shell to install the plugins. OPTIONS --help Show this help page. --version Show version information. --debug Print debug information on the operations of "munin-node-configure". This can be very verbose. All debugging output is printed to STDOUT, and each line is prefixed with '#'. Only errors are printed to STDERR. --pidebug Plugin debug. Sets the environment variable MUNIN_DEBUG to 1 so that plugins may enable debugging. --config <file> Override configuration file [/usr/local/etc/munin/munin-node.conf] --servicedir <dir> Override plugin directory [/usr/local/etc/munin/plugins/] --sconfdir <dir> Override plugin configuration directory [/usr/local/etc/munin/plu- gin-conf.d/] --libdir <dir> Override plugin library [/usr/local/share/munin/plugins/] --suggest Suggest plugins that might be added or removed, instead of those that are currently enabled. OUTPUT OPTIONS By default, "munin-node-configure" will print out a table summarising the results. --shell Instead of a table, print shell commands to install the new plugin sug- gestions. This implies "--suggest", unless "--snmp" was also enabled. By de- fault, it will not attempt to remove any plugins. --remove-also When "--shell" is enabled, also provide commands to remove plugins that are no longer applicable from the service directory. PLUGIN SELECTION OPTIONS --families <family,...> Override the list of families that will be used (auto, manual, contrib, snmpauto). Multiple families can be specified as a comma-separated list, by repeating the "--families" option, or as a combination of the two. When listing installed plugins, the default families are 'auto', 'man- ual' and 'contrib'. Only 'auto' plugins are checked for suggestions. SNMP probing is only performed on 'snmpauto' plugins. --newer <version> Only consider plugins added to the Munin core since <version>. This option is useful when upgrading, since it can prevent plugins that have been manually removed from being reinstalled. This only applies to plugins in the 'auto' family. SNMP Options --snmp <host|cidr,...> Probe the SNMP agents on the host or CIDR network (e.g. "192.168.1.0/24"), to see what plugins they support. This may take some time, especially if the many hosts are specified. This option can be specified multiple times, or as a comma-separated list, to include more than one host/CIDR. --snmpversion <ver> The SNMP version (1, 2c or 3) to use. ['2c'] --snmpport <port> The SNMP port to use [161] --snmpdomain <domain> The Transport Domain to use for exchanging SNMP messages. The default is UDP/IPv4. Possible values: 'udp', 'udp4', 'udp/ipv4'; 'udp6', 'udp/ipv6'; 'tcp', 'tcp4', 'tcp/ipv4'; 'tcp6', 'tcp/ipv6'. SNMP 1/2c authentication SNMP versions 1 and 2c use a "community string" for authentication. This is a shared password, sent in plaintext over the network. --snmpcommunity <string> The community string for version 1 and 2c agents. ['public'] (If this works your device is probably very insecure and needs a security checkup). SNMP 3 authentication SNMP v3 has three security levels. Lowest is "noAuthNoPriv", which pro- vides neither authentication nor encryption. If a username and "auth- password" are given it goes up to "authNoPriv", and the connection is authenticated. If "privpassword" is also given the security level be- comes "authPriv", and the connection is authenticated and encrypted. Note: Encryption can slow down slow or heavily loaded network devices. For most uses "authNoPriv" will be secure enough -- the password is sent over the network encrypted in any case. ContextEngineIDs are not (yet) supported. For further reading on SNMP v3 security models please consult RFC3414 and the documentation for Net::SNMP. --snmpusername <name> Username. There is no default. --snmpauthpassword <password> Authentication password. Optional when encryption is also enabled, in which case defaults to the privacy password ("--snmpprivpassword"). --snmpauthprotocol <protocol> Authentication protocol. One of 'md5' or 'sha' (HMAC-MD5-96, RFC1321 and SHA-1/HMAC-SHA-96, NIST FIPS PIB 180, RFC2264). ['md5'] --snmpprivpassword <password> Privacy password to enable encryption. There is no default. An empty ('') password is considered as no password and will not enable encryp- tion. Privacy requires a privprotocol as well as an authprotocol and a auth- password, but all of these are defaulted (to 'des', 'md5', and the privpassword value, respectively) and may therefore be left unspeci- fied. --snmpprivprotocol <protocol> If the privpassword is set this setting controls what kind of encryp- tion is used to achieve privacy in the session. Only the very weak 'des' encryption method is supported officially. ['des'] munin-node-configure also supports '3des' (CBC-3DES-EDE, aka Triple-DES, NIST FIPS 46-3) as specified in IETF draft-reeder-sn- mpv3-usm-3desede. Whether or not this works with any particular de- vice, we do not know. FILES /usr/local/etc/munin/munin-node.conf /usr/local/etc/munin/plugin-conf.d/* /usr/local/etc/munin/plugins/* /usr/local/share/munin/plugins/plugins.history /usr/local/share/munin/plugins/* VERSION This is munin-node-configure (munin-node) v2.0.76. AUTHORS Jimmy Olsen, Nicolai Langfeldt, Matthew Boyle COPYRIGHT Copyright (C) 2003-2006 Jimmy Olsen, Nicolai Langfeldt. Copyright (C) 2009-2010 Matthew Boyle This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. This program is released under the GNU General Public License perl v5.42.3 2026-08-04 MUNIN-N...NFIGURE(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | FILES | VERSION | AUTHORS | COPYRIGHT
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=munin-node-configure&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>