FreeBSD Manual Pages
qconfirm-check(1) General Commands Manual qconfirm-check(1) NAME qconfirm-check - request delivery confirmation under qmail SYNOPSIS in .qmail: |qconfirm-check [-mnbD] [-d dir] [-i bytes] [-t timeout] [prog] DESCRIPTION qconfirm-check (perhaps) requests delivery confirmations from the enve- lope sender to allow further processing in the .qmail file. qconfirm-check can operate either sender-based or message-based, see below for sender mode and message mode. Messages with an empty envelope sender and the envelope sender <#@[]> are allowed by default. WARNING: If you create a .qmail file to enable qconfirm-check, make sure to also add a line specifying delivery to your normal mailbox. SENDER MODE If qconfirm-check runs in sender mode, messages from known envelope senders are accepted without a confirmation, and immediately allowed to be processed further in the .qmail file. qconfirm-check defers messages from unknown envelope senders temporar- ily, and sends a confirmation request message to the sender. The orig- inal message and all newer messages from the same sender will be de- ferred temporarily until a reply to the confirmation request is re- ceived. A message bounces if queuelifetime has expired. New messages from the same sender do not result in new confirmation requests. Once an envelope sender has confirmed a delivery, qconfirm-check treats this envelope sender as known. MESSAGE MODE If qconfirm-check runs in message mode (option -m is set), each single message needs to be confirmed to be allowed to be processed further in the .qmail file. A message bounces if queuelifetime has expired. OPTIONS -m message mode. qconfirm-check identifies the message by its in- ode. Each message must be confirmed before it is allowed to be processed further in the .qmail file. Without this option qcon- firm-check runs in sender mode. -n no acknowledge. Do not acknowledge the receipt of a reply to a confirmation request. -b bad. Only works in sender mode. After checking if the envelope sender is currently pending or ok, check if it is matched as bad. -D no domain match. Only takes effect in sender mode. Don't use extended envelope sender address matching for domains and sub- domains. This applies for matching senders for ok and bad. -d dir Override the default qconfirm directory (``~/.qconfirm'') and the environment variable QCONFIRM_DIR with dir. -i bytes include the top bytes bytes of the sender's message at the bot- tom of a confirmation request or acknowledgement. Default is 8192. -t timeout Set the timeout for sending confirmation requests as reminders to timeout seconds. Unaccepted and unconfirmed messages are held in the queue. Whenever qmail tries to deliver the message, qconfirm-check checks if timeout or more seconds have expired since a confirmation request was sent. If so, qconfirm-check again sends a confirmation request as reminder. If timeout is zero, only one confirmation request per message or sender is sent and no reminders. Default is 345586 (ca. four days). prog prog can be omitted or consists of one or more arguments. If prog is set, qconfirm-check sets the environment variable QCON- FIRM_DIR=dir and runs prog just before requesting a delivery confirmation. If prog exits zero, qconfirm-check allows the message to be processed further in the .qmail file without a confirmation and exits immediately. If prog exits 111, qcon- firm-check exits 111 immediately. In all other cases qconfirm- check continues and requests a delivery confirmation. CONFIGURATION qconfirm-check reads its configuration from files in the subdirectory conf/ of the qconfirm directory (normally ``~/.qconfirm/conf/''). Only the first line of a configuration file is considered. QCONFIRM_MAILNAME The configuration file QCONFIRM_MAILNAME overrides the default mailname in the from header of confirmation requests and ac- knowledgements (``qconfirm''). QCONFIRM_EXT The configuration file QCONFIRM_EXT overrides the default exten- sion used for receiving message confirmations (``qconfirm-''). QCONFIRM_PREPEND This configuration file must be set if the mail address you run qconfirm for is controlled through qmail's virtualdomains. It must be set to the prepend part of the corresponding entry in /var/qmail/control/virtualdomains plus a dash at the end. QCONFIRM_HOST The configuration file QCONFIRM_HOST if set overrides the envi- ronment variable HOST normally set by qmail-local(8). QCONFIRM_ACCEPT The configuration file QCONFIRM_ACCEPT overrides the default in- vocation of qconfirm-accept(1) in automatically created .qmail files (``qconfirm-accept''). QCONFIRM_ACCEPT_PROG If QCONFIRM_ACCEPT_PROG is set, its value is used as prog argu- ment to qconfirm-accept(8) in automatically created .qmail files. ENVIRONMENT QCONFIRM_DIR The environment variable QCONFIRM_DIR overrides the default lo- cation of the user's qconfirm directory (``.qconfirm/''). FILES ~/.qconfirm/conf/ ~/.qconfirm/pending/ ~/.qconfirm/ok/ ~/.qconfirm/bad/ ~/.qconfirm/msg/request ~/.qconfirm/msg/acknowledge SEE ALSO qconfirm(1), qconfirm-accept(1), qconfirm-conf(1), qconfirm-inject(1), qconfirm-notice(1), qconfirm-return(1), qconfirm-control(1), qconfirm- cdb-check(1), qconfirm-cdb-update(1) http://smarden.org/qconfirm/ AUTHOR Gerrit Pape <pape@smarden.org> qconfirm-check(1)
NAME | SYNOPSIS | DESCRIPTION | SENDER MODE | MESSAGE MODE | OPTIONS | CONFIGURATION | ENVIRONMENT | FILES | SEE ALSO | AUTHOR
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=qconfirm-check&sektion=1&manpath=FreeBSD+Ports+15.0>