FreeBSD Manual Pages
RIGSMTR(1) Hamlib Utilities RIGSMTR(1) NAME rigsmtr - measure S-Meter vs azimuth using Hamlib SYNOPSIS rigsmtr [-hvV] [-m id] [-r device] [-s baud] [-c id] [-C parm=val] [-M id] [-R device] [-S baud] [-N parm=val] [time_step] DESCRIPTION rigsmtr uses Hamlib to control a radio to measure S-Meter value versus an- tenna azimuth. It rotates the antenna from minimum azimuth to maximum azimuth. Every sec- ond, or time_step if specified in seconds, it retrieves the signal strength. Azimuth in degrees and the corresponding S-Meter level in dB rel- ative to S9 are then printed on stdout. To work correctly, rigsmtr needs a radio that could measure S-Meter and a Hamlib backend that is able to retrieve it, connected to a Hamlib supported rotator. Keep in mind that Hamlib is BETA level software. While a lot of backend libraries lack complete radio support, the basic functions are usually well supported. Please report bugs and provide feedback at the e-mail address given in the BUGS section below. Patches and code enhancements sent to the same address are welcome. OPTIONS This program follows the usual GNU command line syntax. Short options that take an argument may have the value follow immediately or be separated by a space. Long options starting with two dashes (`-') require an `=' between the option and any argument. Here is a summary of the supported options. -m, --model=id Select radio model number. See model list (use "rigctl -l"). -r, --rig-file=device Use device as the file name of the port connected to the radio. Often a serial port, but could be a USB to serial adapter. Typi- cally /dev/ttyS0, /dev/ttyS1, /dev/ttyUSB0, etc. on Linux, COM1, COM2, etc. on MS Windows. The BSD flavors and Mac OS/X have their own designations. See your system's documentation. -s, --serial-speed=baud Set radio serial speed to baud rate. Uses maximum serial speed from radio backend capabilities as the de- fault. -c, --civaddr=id Use id as the CI-V address to communicate with the radio. Only useful for Icom and some Ten-Tec radios. Note: The id is in decimal notation, unless prefixed by 0x, in which case it is hexadecimal. -C, --set-conf=parm=val[,parm=val] Set radio configuration parameter(s), e.g. stop_bits=2. Use the -L option of rigctl for a list of configuration parameters for a given model number. -M, --rot-model=id Select rotator model number. See model list (use "rotctl -l"). -R, --rot-file=device Use device as the file name of the port connected to the rotator. Often a serial port, but could be a USB to serial adapter. Typi- cally /dev/ttyS0, /dev/ttyS1, /dev/ttyUSB0, etc. on Linux, COM1, COM2, etc. on MS Windows. The BSD flavors and Mac OS/X have their own designations. See your system's documentation. -S, --rot-serial-speed=baud Set rotator serial speed to baud rate. Uses maximum serial speed from rotator backend capabilities as the default. -N, --rot-set-conf=parm=val[,parm=val] Set rotator configuration parameter(s), e.g. stop_bits=2. Use the -L option of rotctl for a list of configuration parameters for a given model number. -v, --verbose Set verbose mode, cumulative (see DIAGNOSTICS below). -h, --help Show a summary of these options and exit. -V, --version Show version of rigsmtr and exit. Note: Some options may not be implemented by a given backend and will re- turn an error. This is most likely to occur with the --set-conf and --rot-set-conf options. DIAGNOSTICS The -v, --verbose option allows different levels of diagnostics to be out- put to stderr and correspond to -v for BUG, -vv for ERR, -vvv for WARN, -vvvv for VERBOSE, or -vvvvv for TRACE. A given verbose level is useful for providing needed debugging information to the email address below. For example, TRACE output shows all of the values sent to and received from the radio which is very useful for radio backend library development and may be requested by the developers. EXIT STATUS rigsmtr exits with: 0 if all operations completed normally; 1 if there was an invalid command line option or argument; 2 if an error was returned by Hamlib; 3 if the radio doesn't have the required capabilities. EXAMPLE Collect S-Meter readings on a TS-850 while an EasycommII rotator makes a full 360<degree> rotation and record measurements in the file csmtr (typed text shown in bold): $ rigsmtr -m 2009 -r /dev/ttyS1 -M 202 > csmtr After completion the file csmtr contains lines such as: 0 -47 30 -40 60 -22 90 -3 120 10 150 1 180 -11 210 -24 240 -35 270 -42 300 -48 330 -51 360 -49 The results can be plotted with gnuplot(1): $ gnuplot set angles degrees set polar set grid polar 15. unset border unset param set style data line set rrange [-60:60] set xrange [-60:60] set yrange [-60:60] plot csmtr BUGS Report bugs to: Hamlib Developer mailing list COPYING This file is part of Hamlib, a project to develop a library that simplifies radio, rotator, and amplifier control functions for developers of software primarily of interest to radio amateurs and those interested in radio com- munications. Copyright (C) 2007-2009 Stephane Fillod Copyright (C) 2018-2020 Nate Bargmann This is free software; see the file COPYING for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. SEE ALSO gnuplot(1), rigctl(1), rotctl(1), hamlib(7) COLOPHON Links to the Hamlib Wiki, Git repository, release archives, and daily snap- shot archives are available via hamlib.org. Hamlib 2020-09-09 RIGSMTR(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | DIAGNOSTICS | EXIT STATUS | EXAMPLE | BUGS | COPYING | SEE ALSO | COLOPHON
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=rigsmtr&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>