SG3_UTILS(8) SG3_UTILS SG3_UTILS(8) NAME sg3_utils - a package of utilities for sending SCSI commands SYNOPSIS sg_* [--dry-run] [--enumerate] [--help] [--hex] [--in=FN] [--inhex=FN] [--json[=JO]] [--js-file=JFN] [--maxlen=LEN] [--raw] [--timeout=SECS] [--verbose] [--version] [OTHER_OPTIONS] [DEVICE] DESCRIPTION sg3_utils is a package of utilities that send SCSI commands to the given DEVICE via a SCSI pass through interface provided by the host operating system. The names of all utilities start with "sg" and most start with "sg_" often followed by the name, or a shortening of the name, of the SCSI command that they send. For example the "sg_verify" utility sends the SCSI VERIFY com- mand. A mapping between SCSI commands and the sg3_utils utilities that is- sue them is shown in the COVERAGE file. The sg_raw utility can be used to send an arbitrary SCSI command (supplied on the command line) to the given DEVICE. sg_decode_sense can be used to decode SCSI sense data given on the command line or in a file. sg_raw -vvv will output the T10 name of a given SCSI CDB which is most often 16 bytes or less in length. SCSI draft standards can be found at https://www.t10.org . The standards themselves can be purchased from ANSI and other standards organizations. A good overview of various SCSI standards can be seen in https://www.t10.org/scsi-3.htm with the SCSI command sets in the upper part of the diagram. The highest level (i.e. most abstract) document is the SCSI Architecture Model (SAM) with SAM-5 being the most recent standard (ANSI INCITS 515-2016) with the most recent draft being SAM-6 revision 4 . SCSI commands in common with all device types can be found in SCSI Primary Com- mands (SPC) of which SPC-5 is the most recent standard (ANSI INCITS 502-2020). The most recent SPC draft is SPC-6 revision 6. Block device spe- cific commands (e.g. as used by disks) are in SBC, those for tape drives in SSC, those for SCSI enclosures in SES and those for CD/DVD/BD drives in MMC. It is becoming more common to control ATA disks with the SCSI command set. This involves the translation of SCSI commands to their corresponding ATA equivalents (and that is an imperfect mapping in some cases). The relevant standard is called SCSI to ATA Translation (SAT, SAT-2 and SAT-3) are now standards at INCITS(ANSI) and ISO while SAT-4 is at the draft stage. The logic to perform the command translation is often called a SAT Layer or SATL and may be within an operating system, in host bus adapter firmware or in an external device (e.g. associated with a SAS expander). See https://www.t10.org for more information. There is some support for SCSI tape devices but not for their basic opera- tion. The reader is referred to the "mt" utility. There are two generations of command line option usage. The newer utilities (written since July 2004) use the getopt_long() function to parse command line options. With that function, each option has two representations: a short form (e.g. '-v') and a longer form (e.g. '--verbose'). If an argument is required then it follows a space (optionally) in the short form and a "=" in the longer form (e.g. in the sg_verify utility '-l 2a6h' and '--lba=2a6h' are equivalent). Note that with getopt_long(), short form op- tions can be elided, for example: '-all' is equivalent to '-a -l -l'. The DEVICE argument may appear after, between or prior to any options. The older utilities, including as sg_inq, sg_logs, sg_modes, sg_opcode, sg_rbuff, sg_readcap, sg_senddiag, sg_start and sg_turs had individual com- mand line processing code typically based on a single "-" followed by one or more characters. If an argument is needed then it follows a "=" ( e.g. '-p=1f' in sg_modes with its older interface). Various options can be elided as long as it is not ambiguous (e.g. '-vv' to increase the ver- bosity). Over time the command line interface of these older utilities became messy and overloaded with options. So in sg3_utils version 1.23 the command line interface of these older utilities was altered to have both a cleaner getopt_long() interface and their older interface for backward compatibil- ity. By default these older utilities use their getopt_long() based inter- face. The getopt_long() is a GNU extension (i.e. not yet POSIX certified) but more recent command line utilities tend to use it. That can be overrid- den by defining the SG3_UTILS_OLD_OPTS environment variable or using '-O' or '--old' as the first command line option. The man pages of the older utilities documents the details. Several sg3_utils utilities are based on the Unix dd command (e.g. sg_dd) and permit copying data at the level of SCSI READ and WRITE commands. sg_dd is tightly bound to Linux and hence is not ported to other OSes. A more generic utility (than sg_dd) called ddpt in a package of the same name has been ported to other OSes. ENVIRONMENT VARIABLES The SG3_UTILS_OLD_OPTS environment variable is explained in the previous section. It is only for backward compatibility of the command line options for older utilities. The SG3_UTILS_INVOCATION environment variable has been implemented on some utilities that decode a lot of data. When SG3_UTILS_INVOCATION is set those utilities will print out a line of 60 "v" characters. After that the util- ity name and version (which includes a date) followed by a line by line breakdown of the command line arguments that the utility was invoked with. The command line arguments include the utility name and options in the or- der they were given. The output is sent to stdout. The option is designed to help automatic testing of utilities in the package. The SG3_UTILS_DSENSE environment variable may be set to a number. It is only used by the embedded SNTL within the library used by the utilities in this library. SNTL is a SCSI to NVMe Translation Layer. This environment variable defaults to 0 which will lead to any utility that issues a SCSI command that is translated to a NVMe command (by the embedded SNTL) that fails at the NVMe device, to return SCSI sense in 'fixed' format. If this variable is non-zero then then the returned SCSI sense will be in 'descrip- tor' format. Several utilities have their own environment variable setting (e.g. sg_persist has SG_PERSIST_IN_RDONLY). See individual utility man pages for more information. There is a Linux specific environment variable called SG3_UTILS_LINUX_NANO that if defined and the sg driver in the system is 4.0.30 or later, will show command durations in nanoseconds rather than the default milliseconds. Command durations are typically only shown if --verbose is used 3 or more times. Due to an interface problem (a 32 bit integer that should be 64 bits with the benefit of hindsight) the maximum duration that can be represented in nanoseconds is about 4.2 seconds. If longer durations may occur then don't define this environment variable (or undefine it). LINUX DEVICE NAMING Most disk block devices have names like /dev/sda, /dev/sdb, /dev/sdc, etc. SCSI disks in Linux have always had names like that but in recent Linux kernels it has become more common for many other disks (including SATA disks and USB storage devices) to be named like that. Partitions within a disk are specified by a number appended to the device name, starting at 1 (e.g. /dev/sda1 ). Tape drives are named /dev/st<num> or /dev/nst<num> where <num> starts at zero. Additionally one letter from this list: "lma" may be appended to the name. CD, DVD and BD readers (and writers) are named /dev/sr<num> where <num> start at zero. There are less used SCSI device type names, the dmesg and the lsscsi commands may help to find if any are attached to a running system. There is also a SCSI device driver which offers alternate generic access to SCSI devices. It uses names of the form /dev/sg<num> where <num> starts at zero. The "lsscsi -g" command may be useful in finding these and which generic name corresponds to a device type name (e.g. /dev/sg2 may corre- spond to /dev/sda). In the lk 2.6 series a block SCSI generic driver was introduced and its names are of the form /dev/bsg/<h:c:t:l> where h, c, t and l are numbers. Again see the lsscsi command to find the correspondence between that SCSI tuple (i.e. <h:c:t:l>) and alternate device names. Prior to the Linux kernel 2.6 series these utilities could only use generic device names (e.g. /dev/sg1 ). In almost all cases in the Linux kernel 2.6 series, any device name can be used by these utilities. Very little has changed in Linux device naming in the Linux kernel 3 and 4 series. WINDOWS DEVICE NAMING Storage and related devices can have several device names in Windows. Probably the most common in the volume name (e.g. "D:"). There are also a "class" device names such as "PhysicalDrive<n>", "CDROM<n>" and "TAPE<n>". <n> is an integer starting at 0 allocated in ascending order as devices are discovered (and sometimes rediscovered). Some storage devices have a SCSI lower level device name which starts with a SCSI (pseudo) adapter name of the form "SCSI<n>:". To this is added sub-addressing in the form of a "bus" number, a "target" identifier and a LUN (Logical Unit Number). The "bus" number is also known as a "PathId". These are assembled to form a device name of the form: "SCSI<n>:<bus>,<tar- get>,<lun>". The trailing ",<lun>" may be omitted in which case a LUN of zero is assumed. This lower level device name cannot often be used directly since Windows blocks attempts to use it if a class driver has "claimed" the device. There are SCSI device types (e.g. Automation/Drive interface type) for which there is no class driver. At least two transports ("bus types" in Windows jargon): USB and IEEE 1394 do not have a "scsi" device names of this form. In keeping with DOS file system conventions, the various device names can be given in upper, lower or mixed case. Since "PhysicalDrive<n>" is tedious to write, a shortened form of "PD<n>" is permitted by all utilities in this package. A single device (e.g. a disk) can have many device names. For example: "PD0" can also be "C:", "D:" and "SCSI0:0,1,0". The two volume names re- flect that the disk has two partitions on it. Disk partitions that are not recognized by Windows are not usually given a volume name. However Vista does show a volume name for a disk which has no partitions recognized by it and when selected invites the user to format it (which may be rather un- friendly to other OSes). These utilities assume a given device name is in the Win32 device name- space. To make that explicit "\\.\" can be prepended to the device names mentioned in this section. Beware that backslash is an escape character in Unix like shells and the C programming language. In a shell like Msys (from MinGW) each backslash may need to be typed twice. The sg_scan utility within this package lists out Windows device names in a form that is suitable for other utilities in this package to use. FREEBSD DEVICE NAMING SCSI disks have block names of the form /dev/da<num> where <num> is an in- teger starting at zero. The "da" is replaced by "sa" for SCSI tape drives and "cd" for SCSI CD/DVD/BD drives. Each SCSI device has a corresponding pass-through device name of the form /dev/pass<num> where <num> is an inte- ger starting at zero. The "camcontrol devlist" command may be useful for finding out which SCSI device names are available and the correspondence between class and pass-through names. FreeBSD allows device names to be given without the leading "/dev/" (e.g. da0 instead of /dev/da0). That worked in this package up until version 1.43 when the unadorned device name (e.g. "da0") gave an error. The original ac- tion (i.e. allowing unadorned device names) has been restored in version 1.46 . Also note that symlinks (to device names) are followed before prepending "/dev/" if the resultant name doesn't start with a "/". FreeBSD's NVMe naming has been evolving. The controller naming is the same as Linux: "/dev/nvme<n>" but the namespaces have an extra "s" (e.g. "/dev/nvme0ns1"). The latter is not a block (GEOM) device (strictly speak- ing FreeBSD does not have block devices). Initially FreeBSD had "/dev/nvd<m>" GEOM devices that were not based on the CAM subsystem. Then in FreeBSD release 12 a new nda driver was added that is CAM (and GEOM) based for NVMe namespaces; it has names like "/dev/nda0". The preferred device nodes for this package are "/dev/nvme0" for NVMe controllers and "/dev/nda0" for NVMe namespaces. SOLARIS DEVICE NAMING SCSI device names below the /dev directory have a form like: c5t4d3s2 where the number following "c" is the controller (HBA) number, the number follow- ing "t" is the target number (from the SCSI parallel interface days) and the number following "d" is the LUN. Following the "s" is the slice number which is related to a partition and by convention "s2" is the whole disk. OpenSolaris also has a c5t4d3p2 form where the number following the "p" is the partition number apart from "p0" which is the whole disk. So a whole disk may be referred to as either c5t4d3, c5t4d3s2 or c5t4d3p0 . And these device names are duplicated in the /dev/dsk and /dev/rdsk direc- tories. The former is the block device name and the latter is for "raw" (or char device) access which is what sg3_utils needs. So in OpenSolaris some- thing of the form 'sg_inq /dev/rdsk/c5t4d3p0' should work. If it doesn't work then add a '-vvv' option for more debug information. Trying this form 'sg_inq /dev/dsk/c5t4d3p0' (note "rdsk" changed to "dsk") will result in an "inappropriate ioctl for device" error. The device names within the /dev directory are typically symbolic links to much longer topological names in the /device directory. In Solaris cd/dvd/bd drives seem to be treated as disks and so are found in the /dev/rdsk directory. Tape drives appear in the /dev/rmt directory. There is also a sgen (SCSI generic) driver which by default does not attach to any device. See the /kernel/drv/sgen.conf file to control what is at- tached. Any attached device will have a device name of the form /dev/scsi/c5t4d3 . Listing available SCSI devices in Solaris seems to be a challenge. "Use the 'format' command" advice works but seems a very dangerous way to list de- vices. [It does prompt again before doing any damage.] 'devfsadm -Cv' cleans out the clutter in the /dev/rdsk directory, only leaving what is "live". The "cfgadm -v" command looks promising. NVME SUPPORT NVMe (or NVM Express) is a relatively new storage transport and command set. The level of abstraction of the NVMe command set is somewhat lower the SCSI command sets, closer to the level of abstraction of ATA (and SATA) command sets. NVMe claims to be designed with flash and modern "solid state" storage in mind, something unheard of when SCSI was originally de- veloped in the 1980s. The SCSI command sets' advantage is the length of time they have been in place and the existing tools (like these) to support it. Plus SCSI command sets level of abstraction is both and advantage and disadvantage. Recently the NVME-MI (Management Interface) designers decide to use the SCSI Enclo- sure Services (SES-3) standard "as is" with the addition of two tunnelling NVME-MI commands: SES Send and SES Receive. This means after the OS inter- face differences are taken into account, the sg_ses, sg_ses_microcode and sg_senddiag utilities can be used on a NVMe device that supports a newer version of NVME-MI. The NVME-MI SES Send and SES Receive commands correspond to the SCSI SEND DIAGNOSTIC and RECEIVE DIAGNOSTIC RESULTS commands respectively. There are however a few other commands that need to be translated, the most important of which is the SCSI INQUIRY command to the NVMe Identify controller/name- space. Starting in version 1.43 these utilities contain a small SNTL (SCSI to NVMe Translation Layer) to take care of these details. As a side effect of this "juggling" if the sg_inq utility is used (without the --page= option) on a NVMe DEVICE then the actual NVMe Identifier (con- troller and possibly namespace) responses are decoded and output. However if 'sg_inq --page=sinq <device>' is given for the same DEVICE then parts of the NVMe Identify controller and namespace response are translated to a SCSI standard INQUIRY response which is then decoded and output. Apart from the special case with the sg_inq, all other utilities in the package assume they are talking to a SCSI device and decode any response accordingly. One easy way for users to see the underlying device is a NVMe device is the standard INQUIRY response Vendor Identification field of "NVMe " (an 8 character long string with 4 spaces to the right). The following SCSI commands are currently supported by the SNTL library: INQUIRY, MODE SELECT(10), MODE SENSE(10), READ(10,16), READ CAPAC- ITY(10,16), RECEIVE DIAGNOSTIC RESULTS, REQUEST SENSE, REPORT LUNS, REPORT SUPPORTED OPERATION CODES, REPORT SUPPORTED TASK MANAGEMENT FUNCTIONS, SEND DIAGNOSTICS, START STOP UNIT, SYNCHRONIZE CACHE(10,16), TEST UNIT READY, VERIFY(10,16), WRITE(10,16) and WRITE SAME(10,16). EXIT STATUS To aid scripts that call these utilities, the exit status is set to indi- cate success (0) or failure (1 or more). Note that some of the lower values correspond to the SCSI sense key values. The exit status values listed below can be given to the sg_decode_sense utility (which is found in this package) as follows: sg_decode_sense --err=<exit_status> and a short explanatory string will be output to stdout. The exit status values are: 0 success. Also used for some utilities that wish to return a boolean value for the "true" case (and that no error has occurred). The false case is conveyed by exit status 36. 1 syntax error. Either illegal command line options, options with bad arguments or a combination of options that is not permitted. 2 the DEVICE reports that it is not ready for the operation requested. The DEVICE may be in the process of becoming ready (e.g. spinning up but not at speed) so the utility may work after a wait. In Linux the DEVICE may be temporarily blocked while error recovery is taking place. See exit status values 12 and 13 below which refine this exit value. 3 the DEVICE reports a medium or hardware error (or a blank check). For example an attempt to read a corrupted block on a disk will yield this value. 5 the DEVICE reports an "illegal request" with an additional sense code other than "invalid command operation code". This is often a supported command with a field set requesting an unsupported capa- bility. For commands that require a "service action" field this value can indicate that the command with that service action value is not supported. 6 the DEVICE reports a "unit attention" condition. This usually indi- cates that something unrelated to the requested command has occurred (e.g. a device reset) potentially before the current SCSI command was sent. The requested command has not been executed by the device. Note that unit attention conditions are usually only reported once by a device. 7 the DEVICE reports a "data protect" sense key. This implies some mechanism has blocked writes (or possibly all access to the media). 9 the DEVICE reports an illegal request with an additional sense code of "invalid command operation code" which means that it doesn't sup- port the requested command. 10 the DEVICE reports a "copy aborted". This implies another command or device problem has stopped a copy operation. The EXTENDED COPY fam- ily of commands (including WRITE USING TOKEN) may return this sense key. 11 the DEVICE reports an aborted command. In some cases aborted com- mands can be retried immediately (e.g. if the transport aborted the command due to congestion). 12 the DEVICE reports a sense key of not ready together with an addi- tional sense code of "target port in standby state". 13 the DEVICE reports a sense key of not ready together with an addi- tional sense code of "target port in unavailable state". 14 the DEVICE reports a miscompare sense key. VERIFY and COMPARE AND WRITE commands may report this. 15 the utility is unable to open, close or use the given DEVICE or some other file. The given file name could be incorrect or there may be permission problems. Adding the '-v' option may give more informa- tion. 17 a SCSI "Illegal request" sense code received with a flag indicating the Info field is valid. This is often a LBA but its meaning is com- mand specific. 18 the DEVICE reports a medium or hardware error (or a blank check) with a flag indicating the Info field is valid. This is often a LBA (of the first encountered error) but its meaning is command spe- cific. 19 the DEVICE reports an illegal request with an additional sense code of "invalid field in parameter list". The parameter list is extra data sent to the DEVICE for some commands (e.g. FORMAT UNIT) 20 the DEVICE reports it has a check condition but "no sense" and non-zero information in its additional sense codes. Some polling commands (e.g. REQUEST SENSE) can receive this response. There may be useful information in the sense data such as a progress indica- tion. 21 the DEVICE reports a "recovered error". The requested command was successful. Most likely a utility will report a recovered error to stderr and continue, probably leaving the utility with an exit sta- tus of 0 . 22 the DEVICE reports that the current command or its parameters imply a logical block address (LBA) that is out of range. This happens surprisingly often when trying to access the last block on a storage device; either a classic "off by one" logic error or a misreading of the response from READ CAPACITY(10 or 16) in which the address of the last block rather than the number of blocks on the DEVICE is re- turned. Since LBAs are origin zero they range from 0 to n-1 where n is the number of blocks on the DEVICE, so the LBA of the last block is one less than the total number of blocks. 24 the DEVICE reports a SCSI status of "reservation conflict". This means access to the DEVICE with the current command has been blocked because another machine (HBA or SCSI "initiator") holds a reserva- tion on this DEVICE. On modern SCSI systems this is related to the use of the PERSISTENT RESERVATION family of commands. 25 the DEVICE reports a SCSI status of "condition met". Currently only the PRE-FETCH command (see SBC-4) yields this status. 26 the DEVICE reports a SCSI status of "busy". SAM-6 defines this sta- tus as the logical unit is temporarily unable to process a command. It is recommended to re-issue the command. 27 the DEVICE reports a SCSI status of "task set full". 28 the DEVICE reports a SCSI status of "ACA active". ACA is "auto con- tingent allegiance" and is seldom used. 29 the DEVICE reports a SCSI status of "task aborted". SAM-5 says: "This status shall be returned if a command is aborted by a command or task management function on another I_T nexus and the Control mode page TAS bit is set to one". 31 error involving two or more command line options. They may be con- tradicting, select an unsupported mode, or a required option (given the context) is missing. 32 there is a logic error in the utility. It corresponds to code com- ments like "shouldn't/can't get here". Perhaps the author should be informed. 33 the command sent to DEVICE has timed out. 34 this is a Windows only exit status and indicates that the Windows error number (32 bits) cannot meaningfully be mapped to an equiva- lent Unix error number returned as the exit status (7 bits). 35 a transport error has occurred. This will either be in the driver (e.g. HBA driver) or in the interconnect between the host (initia- tor) and the device (target). For example in SAS an expander can run out of paths and thus be unable to return the user data from a READ command. 36 no error has occurred plus the utility wants to convey a boolean value of false. The corresponding true value is conveyed by a 0 exit status. 40 the command sent to DEVICE has received an "aborted command" sense key with an additional sense code of 0x10. This value is related to problems with protection information (PI or DIF). For example this error may occur when reading a block on a drive that has never been written (or is unmapped) if that drive was formatted with type 1, 2 or 3 protection. 41 the command sent to DEVICE has received an "aborted command" sense key with an additional sense code of 0x10 (as with error code) plus a flag indicating the Info field is valid. 47 flock (Unix system call) error. 48 this is an internal message indicating a NVMe status field (SF) is other than zero after a command has been executed (i.e. something went wrong). Work in this area is currently experimental. 49 low level driver reports a response's residual count (i.e. number of bytes actually received by HBA is 'requested_bytes - resid- ual_count') that is nonsensical. 50 OS system calls that fail often return a small integer number to help. In Unix these are called "errno" values where 0 implies no er- ror. These error codes set aside 51 to 96 for mapping these errno values but that may not be sufficient. Higher errno values that can- not be mapped are all mapped to this value (i.e. 50). Note that an errno value of 0 is mapped to error code 0. 50 + <os_error_number> OS system calls that fail often return a small integer number to help indicate what the error is. For example in Unix the inability of a system call to allocate memory returns (in 'errno') ENOMEM which often is associated with the integer 12. So 62 (i.e. '50 + 12') may be returned by a utility in this case. It is also possible that a utility in this package reports 50+ENOMEM when it can't allo- cate memory, not necessarily from an OS system call. In recent ver- sions of Linux the file showing the mapping between symbolic con- stants (e.g. ENOMEM) and the corresponding integer is in the kernel source code file: include/uapi/asm-generic/errno-base.h Note that errno values that are greater than or equal to 47 cannot fit in range provided. Instead they are all mapped to 50 as dis- cussed in the previous entry. 97 a SCSI command response failed sanity checks. 98 the DEVICE reports it has a check condition but the error doesn't fit into any of the above categories. 99 any errors that can't be categorized into values 1 to 98 may yield this value. This includes transport and operating system errors af- ter the command has been sent to the device. 100-125 these error codes are used by the ddpt utility which uses the sg3_utils library. They are mainly specialized error codes associ- ated with offloaded copies. 126 the utility was found but could not be executed. That might occur if the executable does not have execute permissions. 127 This is the exit status for utility not found. That might occur when a script calls a utility in this package but the PATH environment variable has not been properly set up, so the script cannot find the executable. 128 + <signum> If a signal kills a utility then the exit status is 128 plus the signal number. For example if a segmentation fault occurs then a utility is typically killed by SIGSEGV which according to 'man 7 signal' has an associated signal number of 11; so the exit status will be 139 . 255 the utility tried to yield an exit status of 255 or larger. That should not happen; given here for completeness. Most of the error conditions reported above will be repeatable (an example of one that is not is "unit attention") so the utility can be run again with the '-v' option (or several) to obtain more information. COMMON OPTIONS Arguments to long options are mandatory for short options as well. In the short form an argument to an option uses zero or more spaces as a separator (i.e. the short form does not use "=" as a separator). If an option takes a numeric argument then that argument is assumed to be decimal unless otherwise indicated (e.g. with a leading "0x", a trailing "h" or as noted in the usage message). Some options are used uniformly in most of the utilities in this package. Those options are listed below. Note that there are some exceptions. -d, --dry-run utilities that can cause lots of user data to be lost or overwritten sometimes have a --dry-run option. Device modifying actions are typ- ically bypassed (or skipped) to implement a policy of "do no harm". This allows complex command line invocations to be tested before the action required (e.g. format a disk) is performed. The --dry-run op- tion has become a common feature of many command line utilities (e.g. the Unix 'patch' command), not just those from this package. Note that most hyphenated option names in this package also can be given with an underscore rather than a hyphen (e.g. --dry_run). -e, --enumerate some utilities (e.g. sg_ses and sg_vpd) store a lot of information in internal tables. This option will output that information in some readable form (e.g. sorted by an acronym or by page number) then exit. Note that with this option DEVICE is ignored (as are most other options) and no SCSI IO takes place, so the invoker does not need any elevated permissions. -h, -?, --help output the usage message then exit. In a few older utilities the '-h' option requests hexadecimal output. In these cases the '-?' op- tion will output the usage message then exit. -H, --hex for SCSI commands that yield a non-trivial response, print out that response as a series ASCII hexadecimal bytes. When used once, 16 bytes are printed on each line, prefixed by a relative address, starting at 0 (hex). When used twice, an ASCII rendering of the 16 bytes is appended to each line, with non-printable characters re- placed by a '.' . When used three times only the 16 hex bytes are printed on each line (hence no address prefix nor ASCII appended). To produce hexadecimal that can be parsed by other utilities use this option three, four or five times. The use of this option, especially when used multiple times has evolved over time as it has become more useful (at least in testing and fixing bugs). So check this option's description in the manpage of the utility being used. An example of a corner case with the '-HHH' option is with the sg_inq utility and the ATA Information VPD page. The sg_inq utility does not decode the ATA IDENTIFY DEVICE command response but instead outputs hexadecimal 16 bit words (lit- tle endian) suitable for the hdparm utility to decode. -i, --in=FN many SCSI commands fetch a significant amount of data (returned in the data-in buffer) which several of these utilities decode (e.g. sg_vpd and sg_logs). To separate the two steps of fetching the data from a SCSI device and then decoding it, this option has been added. The first step (fetching the data) can be done using the --hex or --raw option and redirecting the command line output to a file (of- ten done with ">" in Unix based operating systems). The difference between --hex and --raw is that the former produces output in ASCII hexadecimal while --raw produces its output in "raw" binary. The second step (i.e. decoding the SCSI response data now held in a file) can be done using this --in=FN option where the file name is FN. If "-" is used for FN then stdin is assumed, again this allows for command line redirection (or piping). That file (or stdin) is assumed to contain ASCII hexadecimal unless the --raw option is also given in which case it is assumed to be binary. Notice that the meaning of the --raw option is "flipped" when used with --in=FN to act on the input, typically it acts on the output data. Since the structure of the data returned by SCSI commands varies considerably then the usage information or the manpage of the util- ity being used should be checked. In some cases --hex may need to be used multiple times (and is more conveniently given as '-HH' or '-HHH). -i, --inhex=FN This option has the same or similar functionality as --in=FN. And perhaps 'inhex' is more descriptive since by default, ASCII hexadec- imal is expected in the contents of file: FN. Alternatively the short form option may be -I or -X. See the "HEX, BINARY AND JSON FORMATS" section below for more information. --json[=JO] The default output of most utilities that decode information re- turned from SCSI devices is designed for human readability. Some- times a more parseable form of output is required and JSON is a pop- ular way to do this. Only utilities that decode a significant amount of SCSI data support this option. The corresponding short option is usually -j[JO] but maybe -J[JO] if -j is already in use. Note that in all cases JO argument is itself optional. See the sg3_utils_json manpage for more information. -J, --js-file=JFN output is in JSON format and it is sent to a file named JFN. If that file exists then it is truncated. By default, the JSON output is sent to stdout. When this option is given, the --json[=JO] option is implied and need not be given. The --json[=JO] option may still be needed to set the JO parameter to non-default values. -m, --maxlen=LEN several important SCSI commands (e.g. INQUIRY and MODE SENSE) have response lengths that vary depending on many factors, only some of which these utilities take into account. The maximum response length is typically specified in the 'allocation length' field of the cdb. In the absence of this option, several utilities use a default allo- cation length (sometimes recommended in the SCSI draft standards) or a "double fetch" strategy. See sg_logs(8) for its description of a "double fetch" strategy. These techniques are imperfect and in the presence of faulty SCSI targets can cause problems (e.g. some USB mass storage devices freeze if they receive an INQUIRY allocation length other than 36). Also use of this option disables any "double fetch" strategy that may have otherwise been used. To head off a class of degenerate bugs, if LEN is less than 16 then it is ignored (usually with a warning message) and the default value is used instead. Some utilities use 4 (bytes), rather than 16, as the cutoff value. -r, --raw for SCSI commands that yield a non-trivial response, output that re- sponse in binary to stdout. If any error messages or warning are produced they are usually sent to stderr so as to not interfere with the output from this option. Some utilities that consume data to send to the DEVICE along with the SCSI command, use this option. Alternatively the --in=FN option causes DEVICE to be ignored and the response data (to be decoded) fetched from a file named FN. In these cases this option may indi- cate that binary data can be read from stdin or from a nominated file (e.g. FN). -t, --timeout=SECS utilities that issue potentially long-running SCSI commands often have a --timeout=SECS option. This typically instructs the operating system to abort the SCSI command in question once the timeout ex- pires. Aborting SCSI commands is typically a messy business and in the case of format like commands may leave the device in a "format corrupt" state requiring another long-running re-initialization com- mand to be sent. The argument, SECS, is usually in seconds and the short form of the option may be something other than -t since the timeout option was typically added later as storage devices grew in size and initialization commands took longer. Since many utilities had relatively long internal command timeouts before this option was introduced, the actual command timeout given to the operating sys- tems is the higher of the internal timeout and SECS. Many long running SCSI commands have an IMMED bit in the CDB which causes the command to return relatively quickly but the requested operation has only been commenced, not completed. In such cases the REQUEST SENSE command can be used to monitor progress via its progress indication field (see the sg_requests and sg_turs utili- ties). Utilities that send such SCSI commands either have an --immed option or a --wait option which is the logical inverse of the "imme- diate" action. Sending a SCSI data access command to a device which is busy performing a long running SCSI command (in background) will typically receive a NOT READY sense key with an additional sense code of 0x04 and a qualifier code which indicates which long running operation the device is performing. An alternate long option form is --tmo=SECS. -v, --verbose increase the level of verbosity, (i.e. debug output). Can be used multiple times to further increase verbosity. The additional output caused by this option is almost always sent to stderr. -V, --version print the version string and then exit. Each utility has its own version number and date of last code change. NUMERIC ARGUMENTS Many utilities have command line options that take numeric arguments. These numeric arguments can be large values (e.g. a logical block address (LBA) on a disk) and can be inconvenient to enter in the default decimal repre- sentation. So various other representations are permitted. Multiplicative suffixes are accepted. They are one, two or three letter strings appended directly after the number to which they apply: c C *1 w W *2 b B *512 k K KiB *1024 KB kB *1000 m M MiB *1048576 MB mB *1000000 g G GiB *(2^30) GB gB *(10^9) t T TiB *(2^40) TB *(10^12) p P PiB *(2^50) PB *(10^15) An example is "2k" for 2048. The large tera and peta suffixes are only available for numeric arguments that might require 64 bits to represent in- ternally. These multiplicative suffixes are compatible with GNU's dd command (since 2002) which claims compliance with SI and with IEC 60027-2. A suffix of the form "x<n>" multiplies the preceding number by <n>. An ex- ample is "2x33" for "66". The left argument cannot be '0' as '0x' will be interpreted as hexadecimal number prefix (see below). The left argument to the multiplication must end in a hexadecimal digit (i.e. 0 to f) and the whole expression cannot have any embedded whitespace (e.g. spaces). An ugly example: "0xfx0x2" for 30. A suffix of the form "+<n>" adds the preceding number to <n>. An example is "3+1k" for "1027". The left argument to the addition must end in a hexadec- imal digit (i.e. 0 to f) and the whole expression cannot have any embedded whitespace (e.g. spaces). Another example: "0xf+0x2" for 17. Alternatively numerical arguments can be given in hexadecimal. There are two syntaxes. The number can be preceded by either "0x" or "0X" as found in the C programming language. The second hexadecimal representation is a trailing "h" or "H" as found in (storage) standards. When hex numbers are given, multipliers cannot be used. For example the decimal value "256" can be given as "0x100" or "100h". HEX, BINARY AND JSON FORMATS Both hexadecimal (ASCII) and binary can be used as low level output of SCSI responses that can be redirected to a file and decoded with a later invoca- tion. JSON output is typically generated after decoding and considered a high level output that may be parsed by some other tool. No utilities in sg3_utils can parse JSON as input. JSON output is outlined in its own manpage, see: sg3_utils_json(8). Binary and especially hexadecimal output can have two roles: for viewing immediately (e.g. when debugging) or as a parsable output that can be de- coded later. The latter action uses the --inhex=FN option. For viewing hexadecimal output (e.g. from a SCSI command response) the --hex option can be used once or twice. Both have output similar to: $ hexdump --no-squeezing -C When there is a single --hex option, the ASCII rendering to the right of each line is not shown; when used twice the ASCII rendering is shown. When the --hex option is used three or more times then the assumption is that it will be parsed later. Only hex data bytes are output, up to 16 per line. This is close to this hexdump invocation: $ hexdump --no-squeezing -C | cut -s -d ' ' -f 2-19 This should remove the first column (i.e. the count) and remove the ASCII rendering to the right. This makes parsing the hexadecimal a lot easier. When used 4 or more times the --hex options adds comments (i.e. lines starting with the hash symbol): $ sg_logs -HHHH -A /dev/sdc # Supported log pages log page [0x0]: 00 00 00 03 00 0d 2f # Supported log pages and subpages log page [0x0, 0xff]: 40 ff 00 0e 00 00 00 ff 0d 00 0d 01 0d ff 2f 00 2f ff ... Comments can also be placed after hex in a line, everything from the '#' to the end of a line is ignored. There are many examples of hex files suitable for the --inhex=FN option in the 'inhex' directory. The naming of files in that directory is the name of the utility that will decode it with the "sg_" prefix removed and a ".hex" suffix added. Those hex files can be viewed with a text editor and most contain an example of invoking it in the leading comments. The hexadecimal format can be converted into binary using the sg_de- code_sense utility with these options: "--inhex=HFN --nodecode --write=WFN". The input (in hex) is in the HFN file while the output is placed in the WFN file. To convert a binary file into a hexadecimal form that can be given as input to various sg3_utils utilities, the sg_decode_sense utility can also be used with these options: "--binary=BFN --nodecode -HHH" and the hex output will be sent to the console (stdout). MICROCODE AND FIRMWARE There are two standardized methods for downloading microcode (i.e. device firmware) to a SCSI device. The more general way is with the SCSI WRITE BUFFER command, see the sg_write_buffer utility. SCSI enclosures have their own method based on the Download microcode control/status diagnostic page, see the sg_ses_microcode utility. SCRIPTS, EXAMPLES and UTILS There are several bash shell scripts in the 'scripts' subdirectory that in- voke compiled utilities (e.g. sg_readcap). Several of the scripts start with 'scsi_' rather than 'sg_'. One purpose of these scripts is to call the same utility (e.g. sg_readcap) on multiple devices. Most of the basic com- piled utilities only allow one device as an argument. Some distributions install these scripts in a more visible directory (e.g. /usr/bin). Some of these scripts have man page entries. See the README file in the 'scripts' subdirectory. There is some example C code plus examples of complex invocations in the 'examples' subdirectory. There is also a README file. The example C may be a simpler example of how to use a SCSI pass-through in Linux than the main utilities (found in the 'src' subdirectory). This is due to the fewer ab- straction layers (e.g. they don't worry the MinGW in Windows may open a file in text rather than binary mode). Some utilities that the author has found useful have been placed in the 'utils' subdirectory. DEBUGGING Each utility and most scripts have a --verbose option (short form: -v) that can be used multiple times to increase the verbosity of the output to aid debugging. Normal output (if any) is sent to stdout while verbose output (and error output) is sent to stderr. This may be important when the (nor- mal output) of a utility is being piped to another command (e.g. the grep command to find a particular field in the output). The Linux SCSI subsystem has a pseudo file for getting and changing the SCSI logging level: /proc/sys/dev/scsi/logging_level . The scsi_log- ging_level script in this package can be used to manipulate the logging level in a command line friendly way. See its manpage. The logging level runs from 0 (no logging and the default) to 7 (lots of logging) and applies to all storage devices that use the SCSI subsystem. The logging output goes to "the log" which is often the /var/log/syslog file. The Linux SCSI generic (sg) driver is often used under the utilities in this package. It uses a seldom (otherwise) used logging type of SCSI_LOG_TIMEOUT. An example of its use to turn on full debugging is: scsi_logging_level -s -T 7 To reduce the amount of output to only error paths, the following is sug- gested: scsi_logging_level -s -T 3 And to turn off logging in the sg driver: scsi_logging_level -s -T 0 For analyzing machine crashes associated with a SCSI command, nothing beats a real serial port. By "real" means that it is _not_ a USB serial port. The reason is that like SCSI, USB needs a functioning software stack within the OS kernel, the very thing that may be crippled during a machine crash. Modern laptops do not have real serial ports and many server machines don't either (or it is an optional extra). In Linux the netconsole module does a pretty good job by sending log entries to another machine (on the same sub-net)) using the UDP ("fire and forget") network protocol . WEB SITE There is a web page discussing this package at https://sg.danny.cz/sg/sg3_utils.html . The device naming used by this package on various operating systems is discussed at: https://sg.danny.cz/sg/device_name.html . There is a git code mirror at https://github.com/hreinecke/sg3_utils . The principle code repository uses subversion and is on the author's equipment. The author keeps track of this via the subversion revision number which is an ascending integer (currently at 922 for this package). The github mirror gets updated periodically from the author's repository. Depending on the time of update, the above Down- loads section at sg.danny.cz may be more up to date than the github mirror. AUTHORS Written by Douglas Gilbert. Some utilities have been contributed, see the CREDITS file and individual source files (in the 'src' directory). REPORTING BUGS Report bugs to <dgilbert at interlog dot com>. COPYRIGHT Copyright (C) 1999-2023 Douglas Gilbert Some utilities are distributed under a GPL version 2 license while others, usually more recent ones, are under a BSD-2-Clause license. The files that are common to almost all utilities and thus contain the most reusable code, namely sg_lib.[hc], sg_cmds_basic.[hc] and sg_cmds_extra.[hc] are under a BSD-2-Clause license. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. SEE ALSO sg3_utils_json,sg_decode_sense(sg3_utils), sdparm(sdparm), ddpt(ddpt), lss- csi(lsscsi), dmesg(1), mt(1), hdparm(hdparm), hexdump(util-linux) The format of this section is: <utility_name>(<package_containing_utility>) or <utility_name>(<manpage_section_number_containing_utility>) . sg3_utils-1.48 August 2023 SG3_UTILS(8)
NAME | SYNOPSIS | DESCRIPTION | ENVIRONMENT VARIABLES | LINUX DEVICE NAMING | WINDOWS DEVICE NAMING | FREEBSD DEVICE NAMING | SOLARIS DEVICE NAMING | NVME SUPPORT | EXIT STATUS | COMMON OPTIONS | NUMERIC ARGUMENTS | HEX, BINARY AND JSON FORMATS | MICROCODE AND FIRMWARE | SCRIPTS, EXAMPLES and UTILS | DEBUGGING | WEB SITE | AUTHORS | REPORTING BUGS | COPYRIGHT | SEE ALSO
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=sg3_utils&sektion=8&manpath=FreeBSD+Ports+15.1.quarterly>