SG_LOGS(8) SG3_UTILS SG_LOGS(8) NAME sg_logs - access log pages with SCSI LOG SENSE command SYNOPSIS sg_logs [--ALL] [--all] [--brief] [--exclude] [--filter=FL] [--full] [--hex] [--json[=JO]] [--js-file=JFN] [--list] [--maxlen=LEN] [--name] [--no_inq] [--page=PG] [--paramp=PP] [--pcb] [--ppc] [--pdt=DT] [--raw] [--readonly] [--sp] [--temperature] [--transport] [--undefined] [--ven- dor=VP] [--verbose] DEVICE sg_logs --inhex=FN [--ALL] [--all] [--brief] [--exclude] [--filter=FL] [--full] [--hex] [--json[=JO]] [--js-file=JFN] [--list] [--name] [--page=PG] [--pdt=DT] [--raw] [--undefined] [--vendor=VP] sg_logs --select [--control=PC] [--page=PG] [--raw] [--reset] [--sp] [--verbose] DEVICE sg_logs --enumerate [--filter=FL] [--help] [--vendor=VP] [--version] sg_logs [-a] [-A] [-b] [-c=PC] [-D=DT] [-e] [-E] [-f=FL] [-F] [-h] [-H] [-i=FN] [-l] [-L] [-m=LEN] [-M=VP] [-n] [-p=PG] [-paramp=PP] [-pcb] [-ppc] [-r] [-R] [-select] [-sp] [-t] [-T] [-u] [-v] [-V] [-?] [-x] DEVICE DESCRIPTION This utility sends a SCSI LOG SENSE command to the DEVICE and then outputs the response. The LOG SENSE command is used to fetch log pages which, if known, are decoded by default. When the --reset and/or --select option is given then a SCSI LOG SELECT command is issued to the DEVICE. Alternatively one or more log page responses can be in a file read using the --inhex=FN option; in this case those responses are decoded and the DEVICE argument, if given, is ignored. In SPC-4 revision 5 the subpage code was introduced to both the LOG SENSE and LOG SELECT command. At the same time a page code field was introduced to the to the LOG SELECT command. The log subpage code can range from 0 to 255 (0xff) inclusive. The subpage code value 255 can be thought of as a wildcard. The SYNOPSIS section above is divided into five forms. The first form shows the options that can be used to send a LOG SENSE command to the DEVICE and decode its response. The second form fetches data from a file (named FN) and decodes it as if it were a response from a LOG SENSE command. The third form shows the options that can be used to send a LOG SELECT command. The fourth form groups various management options. The last form shows the older, deprecated command line interface which is maintained for backward compatibility. When no options are given, just a DEVICE, that is equivalent to calling this utility with the --list option. In that case the names of the sup- ported log pages (but not subpages) are listed out. OPTIONS Arguments to long options are mandatory for short options as well. The op- tions are arranged in alphabetical order based on the long option name. -A, --ALL fetch and decode all the log pages and subpages supported by the DE- VICE. This requires a two stage process: first the "supported log pages and subpages" log page is fetched, then for each entry in its response, the corresponding log page (or subpage) is fetched and displayed. Note that there are many SCSI devices that do not support LOG SENSE subpages and respond to this option with an illegal re- quest sense key. In this case this utility continues by fetching the supported log pages log page instead. In other words if the --ALL option fails then the --all is used instead. The reason is that al- most certainly the DEVICE does not have any log subpages to report. To force an error if the fetch of the supported log pages and sub- pages log page fails use both the --ALL and --full options. Since some vendors don't list all log pages in the "supported log pages and subpages" log page, the '-lll' option can be given in ad- dition. This will merge both "supported ..." log pages then, from that resultant merged list, fetch page contents. This option overrides the --page=PG if the latter is also given. -a, --all outputs all the log pages supported by the DEVICE. This requires a two stage process: first the "supported log pages" log page is fetched, then for each entry in its response, the corresponding log page is fetched and displayed. When used twice (e.g. '-aa') all log pages and subpages are fetched. This option overrides the --page=PG if the latter is also given. -b, --brief shorten the amount of output for some log pages. For example the Tape Alert log page only outputs parameters whose flags are set when --brief is given. -c, --control=PC accepts 0, 1, 2 or 3 for the PC argument: 0 : current threshold values 1 : current cumulative values 2 : default threshold values 3 : default cumulative values The default value is 1 (i.e. current cumulative values). -e, --enumerate this option is used to output information held in this utility's in- ternal tables about known log pages including their name, acronym and fields. If given, the DEVICE argument is ignored. When given once (e.g. '-e') all known pages are listed, sorted in ascending al- phabetical acronym order. When given twice, vendor pages are excluded. When given three times, all known pages are listed, sorted in ascending numeric order listed; when given four times, vendor pages are excluded from the numeric order. The --filter=FL and --verbose options reduce the output of the enu- meration. -E, --exclude this option excludes vendor specific pages and parameters from the output. Trying to decode vendor specific pages and parameters does not necessarily work well for many reasons. This option limits the output to pages and parameters defined by T10. Only parameter fields identified in the drafts as 'vendor specific' are excluded. So parameters codes identified as 'reserved' are shown. -f, --filter=FL FL is either a parameter code when DEVICE is given, or a peripheral device type (pdt) (or other) if --enumerate is given. In the parameter code case FL is a value between 0 and 65535 (0xffff) and only the parameter section matching that code is out- put. If the --hex option is given the log parameter is output in hexadecimal rather than decoding it. If the --hex option is used twice then the leading address on each line of hex is removed. If the --raw option is given then the log parameter is output in bi- nary. Most log pages contain one or more log parameters. Examples of those that don't follow that convention are those pages that list supported log pages (and subpages). In the --enumerate case, when FL >= zero it is taken as a pdt value and only log pages associated with that pdt plus generic pages listed in SPC are enumerated. If FL is -1 then the filter does noth- ing which is the same as not giving this option; when FL is -2 then only generic pages listed in SPC are enumerated. If FL is -10 then only generic direct access like (e.g. disk) pages are enumerated. If FL is -11 then only generic tape like pages (e.g. includes ADC) are enumerated. -F, --full this option is only used in two situations: with the Application client (AC) log page and with the --ALL option. Typically the AC log page has more than 16,000 bytes of user supplied data. Rather than print it all out, the default is to print out the first 64 bytes of data. When this option is given, the application client log pages is fully decoded. When both this option and the --ALL option are given, then this utility will exit with an error if the Supported log pages and sub- pages log page is not available. -h, --help print out the usage message then exit. -H, --hex The default action is to decode known log page numbers (and subpage numbers) into text. When this option is used once, the response is output in hexadecimal. When used twice, each line of hex has the ASCII equivalent shown to the right. When used three times, the hex has no leading address nor trailing ASCII making it suitable to be placed in a file (or piped). That file might later be used by an- other invocation using the --inhex=FN option. A weaker form of this option, called --undefined, handles the for- matting of hexadecimal output for fields that this utility is unable to decode. -i, --in=FN Same as --inhex=FN option. Kept for backward compatibility. -i, --inhex=FN This option may be used in two different contexts. One is with the --select to send a LOG SELECT command to the given DEVICE; see the LOG SELECT section below. The other context is with no DEVICE argument given in which case the contents of FN are decoded as if it were the response of a LOG SENSE command (i.e. one or more log page). For decoding, the page and sub- page numbers are taken from FN while the peripheral device type is either generic (i.e. from SPC) or the value given by --pdt=DT. FN is treated as a file name (or '-' for stdin) which contains ASCII hexadecimal or binary representing a log page. The hexadecimal should be arranged as 1 or 2 digits representing a byte each of which is whitespace or comma separated. Anything from and including a hash mark to the end of line is ignored. If the --raw option is also given then FN is treated as binary. -j[=JO], --json[=JO] output is in JSON format instead of plain text form. Note that argu- ments to the short and long form are themselves optional and if present start with "=" and no whitespace is permitted around that "=". See sg3_utils_json manpage or use '?' for JO to get a summary. -J, --js-file=JFN output is in JSON format and it is sent to a file named JFN. If that file exists then it is truncated. By default, the JSON output is sent to stdout. When this option is given, the --json[=JO] option is implied and need not be given. The --json[=JO] option may still be needed to set the JO parameter to non-default values. -l, --list lists the names of the logs sense pages supported by this device. This is done by reading the "supported log pages" log page. When used once only log pages, but not subpages, are listed. When used twice the "supported log pages and subpages" log page is output. Some vendors do not list some log pages (e.g. those without any sub- pages) in the "supported log pages and subpages" log page. To get a full inventory, this option can be used three times (e.g. '-lll') and the output of the two log pages is merged. Even if the "sup- ported log pages and subpages" log page is not supported using this option three times will yield a list from the "supported log pages" log page. In the absence of other options, the page/subpage names, but not their contents, are shown when this option is given. The '-lll' form may be useful with the --ALL option to show the con- tents of all pages referred to in either the "supported log page" or the "supported log page and subpage" log pages. -m, --maxlen=LEN sets the "allocation length" field in the LOG SENSE cdb. The is the maximum length in bytes that the response will be. Without this op- tion (or LEN equal to 0) this utility first fetches the 4 byte re- sponse then does a second access with the length indicated in the first (4 byte) response. Negative values and 1 for LEN are not ac- cepted. Responses can be quite large (e.g. the background scan re- sults log page) and this option can be used to limit the amount of information returned. The default LEN is 65532 unless the --in=FN option is given; in that case the default is 262144 . -n, --name decode some log pages into 'name=value' entries, one per line. The name contains no space and may be abbreviated and the value is deci- mal unless prefixed by '0x'. Nesting is indicated by leading spaces. This form is meant to be relatively easy to parse. This option is superseded by the --json[=JO] option. If both are given then this option is ignored. -x, --no_inq suppresses the output of information obtained from an initial call to the INQUIRY command for the standard response. The default (as- suming some other options that suppress this output are also not given) is to output several device identification strings. If this option is given twice (or more) then no INQUIRY command is sent hence there will be no device identification string output ei- ther. Also the peripheral device type (PDT) field will not be ob- tained so this utility will not be able to differentiate between some log pages that are device dependent. The utility will assume a PDT of 0 (i.e. a disk) unless the --pdt=DT option is given. -O, --old Switch to older style options. Please use as first option. -p, --page=PG log page name/number to access. PG is either an acronym, a page num- ber, or a page, subpage number pair. Available acronyms can be listed with the --enumerate option. Page (0 to 63) and subpage (0 to 255) numbers are comma separated. They are decimal unless a hexadec- imal indication is given. A hexadecimal number can be specified by a leading "0x" or a trailing "h". A few acronyms specify a range of subpage values in which case the acronym may be followed by a comma then a subpage number. This method can also be used to fetch the Supported subpages log page (e.g. --page=temp,0xff). -P, --paramp=PP PP is the parameter pointer value to place in a field of that name in the LOG SENSE cdb. A number in the range 0 to 65535 (0x0 to 0xffff) is expected. When a value greater than 0 is given the --ppc option should be selected. The default value is 0. For log pages that have parameter codes, the DEVICE should return only parameters code equal to PP or higher in its response. -q, --pcb show Parameter Control Byte settings (only relevant when log parame- ters being output in ASCII). This byte includes the DU and TSD bits plus the 'Format and linking' field (2 bits wide). -D, --pdt=DT DT is the peripheral device type (PDT) that is used when it is not available from the DEVICE. There are several cases: when the DEVICE is not given (e.g. when the --inhex=FN or --enumerate option is given) and when DEVICE is and is coupled with the --no_inq option. That stops this utility sending the SCSI INQUIRY command which is where this utility usually finds the PDT associated log pages being decoded. Numerical values between -1 and 31 (inclusive) may be used where -1 implies what is in SPC. SCSI Primary Commands (SPC) are common to all SCSI devices. Names like 'tape', 'disk' and 'processor' may also be given for DT. The default is 0 or 'disk' for SBC (and the associated standard acronym may also be given which is 'sbc' in this case). -Q, --ppc sets the Parameter Pointer Control (PPC) bit in the LOG SENSE cdb. Default is 0 (i.e. cleared). This bit was made obsolete in SPC-4 re- vision 18. -r, --raw output the response in binary to stdout. Error messages and warnings are output to stderr. This option may also be given together with --in=FN in which case the contents of FN are interpreted as binary data (and the response is decoded as normal, not dumped as binary). -R, --readonly open the DEVICE read-only (e.g. in Unix with the O_RDONLY flag). The default action is to try and open DEVICE read-write then if that fails try to open again with read-only. However when a read-write open succeeds there may still be unwanted actions on the close (e.g. some OSes try to do a SYNCHRONIZE CACHE command). So this option forces a read-only open on DEVICE and if it fails, this utility will exit. Note that options like --select most likely need a read-write open. -R, --reset use SCSI LOG SELECT command (with the PCR bit set) to reset the all log pages (or the given page). Exactly what is reset depends on the accompanying SP bit (i.e. --sp option which defaults to 0) and the PC ("page control") value (which defaults to 1). Supplying this op- tion implies the --select option as well. This option seems to clear error counter log pages but leaves pages like self-test results, start-stop cycle counter and temperature log pages unaffected. This option may be required to clear log pages if a counter reaches its maximum value since the log page in which the counter is found will remain "stuck" at its maximum value until some user interaction (e.g. calling sg_logs with this option). -S, --select use a LOG SELECT command. The default action (i.e. when neither this option nor --reset is given) is to do a LOG SENSE command. See the LOG SELECT section. -s, --sp sets the Saving Parameters (SP) bit. Default is 0 (i.e. cleared). When set this instructs the device to store the current log page pa- rameters (as indicated by the DS and TSD parameter codes) in some non-volatile location. Hence the log parameters will be preserved across power cycles. This option is typically not needed, especially if the GLTSD flag is clear in the control mode page which causes the DEVICE to periodically save all saveable log parameters to non-volatile storage. -t, --temperature outputs the temperature. First looks in the temperature log page and if that is not available tries the Informational Exceptions log page which may also have the current temperature (especially on older disks). -T, --transport outputs the transport ('Protocol specific port') log page. Equiva- lent to setting '--page=18h'. -u, --undefined to see fields decoded, the --hex option cannot be used. However some fields are not defined in the T10 documents and in that case they are output in hex. This option controls the format of 'undefined' fields when they output in hex. Multiple uses of this option has the same sense as the --hex option. For example '-uu' will output unde- fined fields in hexadecimal with an ASCII rendering to the right of each line. -M, --vendor=VP where VP is a vendor/manufacturer (e.g. "sea" for Seagate) or prod- uct (group) acronym (e.g. "lto5" for the 5th generation LTO (tape) consortium). Either the whole log page is vendor specific (e.g. page numbers 0x30 to 0x3f) or part of a T10 defined log page is vendor specific. For example SPC-5 defines parameter code 0x0 of page 0x2f (the Informational Exceptions log page) and states that the remain- ing parameter codes (i.e. 0x1 to 0xffff) are vendor specific. Using a VP of "xxx" will list the available acronyms. If this option is used with --page=PG and PG is an acronym then this option is ignored. If PG is a number (e.g. 0xc0) then VP is used to choose the which vendor specific page (e.g. sharing page number 0xc0) to decode. -v, --verbose increase level of verbosity. When used with --enumerate, in the list of known log page names, those that have no associated decode logic are followed by "[hex only]". -V, --version print out version string then exit. LOG SELECT The SCSI LOG SELECT command can be used to reset certain parameters to ven- dor specific defaults, save them to non-volatile storage (i.e. the media), or supply new page contents. This command has changed between SPC-3 and SPC-4 with the addition of the Page and Subpage Code fields which can only be non zero when the Parameter list length is zero. The --select (or --reset) option is required to issue a LOG SELECT command. If the --in=FN option is not given (or FN is effectively empty) then the Parameter list length field is set to zero. If the --in=FN option is is given then its decoded data is placed in the data-out buffer and its length in bytes is placed in the Parameter list length field. Other options that are active with the LOG SELECT command are --control=PC, --reset (which sets the PCR bit) and --sp. APPLICATION CLIENT This is the name of a log page that acts as a container for data provided by the user. An application client is a SCSI term for the program that is- sues commands to a SCSI initiator (often known as a Host Bus Adapter (HBA)). So, for example, this utility is a SCSI application client. The Application Client log page has 64 log parameters with parameters codes 0 to 63. Each can hold 252 bytes of user binary data. That 252 bytes (or less) of user data, with a 4 byte prefix (for a total of 256 bytes) can be provided with the --in=FN option. A typical prefix would be '0,n,83,fc'. The "n" is the parameter code in hex so the last log parameter would be '0,3f,83,fc'. That log parameter could be read back at some later time with '--page=0xf --filter=0x<n>'. INHEX INSTEAD OF DEVICE This section applies when the --inhex=FN option is used and there is no DE- VICE argument. This can be viewed as a replay facility where the FN file was created by a prior invocation of this utility, most likely with the '-HHHHH' option, with command line output redirection used to create FN. If the --all option is given once then all pages (but not subpages) found in FN will be decoded, or output in hex if this utility is unable to decode some of them. If the --all option is given two or more times then all pages and subpages found in FN will be decoded. In both cases pages are decoded in the order they are found in FN. Next, if the --page=PG] option is given, then FN is searched for a match on PG and, if found, that log (sub)page is decoded. If the --list option is given once, then the Supported log pages log page [0x0,0x0] is decoded, if present. If the --list option is given two or more times, then the Sup- ported Log Pages and Subpages log page [0x0,0xff] is decoded, if present. If none of the above selection options are given, then this utility will attempt to decode the first log page found in FN. If there are more log pages following the first one in FN then they are ignored. NOTES This utility will usually do a double fetch of log pages with the SCSI LOG SENSE command. The first fetch requests a 4 byte response (i.e. place 4 in the "allocation length" field in the cdb). From that response it can calcu- late the actual length of the response which is what it asks for on the second fetch. This is typical practice in SCSI and guaranteed to work in the standards. However some older devices don't comply. For those devices using the --maxlen=LEN option will do a single fetch. A value of 252 should be a safe starting point. Various log pages hold information error rates, device temperature, start stop cycles since the device was produced and the results of the last 20 self tests. Self tests can be initiated by the sg_senddiag(8) utility. The smartmontools package provides much of the information found with sg_logs in a form suitable for monitoring the health of SCSI disks and tape drives. The simplest way to find which log pages can be decoded by this utility is to use the --enumerate option. Some page names are known but there is no decode logic; such cases have "[hex only]" after the log page name when the --verbose option is given with --enumerate. Vendors are specifically permitted by the SPC-6 to _not_ report all pages and subpages supported by a device. That weakens the usefulness of the pages that report a list of supported pages and subpages. One guarantee which is given is that the pages reported shall be in ascending order. EXIT STATUS The exit status of sg_logs is 0 when it is successful. Otherwise see the sg3_utils(8) man page. OLDER COMMAND LINE OPTIONS The options in this section were the only ones available prior to sg3_utils version 1.23 . Since then this utility defaults to the newer command line options which can be overridden by using --old (or -O) as the first option. See the ENVIRONMENT VARIABLES section for another way to force the use of these older command line options. Options with arguments or with two or more letters can have an extra '-' prepended. For example: both '-pcb' and '--pcb' are acceptable. -a outputs all the log pages supported by the DEVICE. Equivalent to --all in the main description. -A outputs all the log pages and subpages supported by the DEVICE. Equivalent to --ALL in the main description. -c=PC Equivalent to --control=PC in the main description. -D=DT Equivalent to --pdt=DT in the main description. -e enumerate internal tables to show information about known log pages. Equivalent to --enumerate in the main description. -E Equivalent to --exclude in the main description. -h suppresses decoding of known log sense pages and prints out the re- sponse in hex instead. -i=FN FN is treated as a file name (or '-' for stdin) which contains ASCII hexadecimal representing a log page that will be sent as parameter data of a LOG SELECT command. See the LOG SELECT section. -H same action as '-h' in this section and equivalent to --hex in the main description. -l lists the names of all logs sense pages supported by this DEVICE. Equivalent to --list in the main description. -L lists the names of all logs sense pages and subpages supported by this DEVICE. Equivalent to '--list --list' in the main description. -m=LEN request only LEN bytes of response data. Default is 0 which is in- terpreted as all that is available. LEN is decimal unless it has a leading '0x' or trailing 'h'. Equivalent to --maxlen=LEN in the main description. -M=VP Equivalent to --vendor=VP in the main description. -n Equivalent to --name in the main description. -N, --new Switch to the newer style options. -p=PG log page code to access. PG is either an acronym, a page number, or a page, subpage pair. Available acronyms can be listed with the --enumerate option. Page (0 to 3f) and subpage (0 to ff) numbers are comma separated. The numbers are assumed to be hexadecimal. -paramp=PP PP is the parameter pointer value (in hex) to place in command. Should be a number between 0 and ffff inclusive. -pcb show Parameter Control Byte settings (only relevant when log parame- ters being output in ASCII). -ppc sets the Parameter Pointer Control (PPC) bit. Default is 0 (i.e. cleared). -r use SCSI LOG SELECT command (PCR bit set) to reset the all log pages (or the given page). Equivalent to --reset in the main description. -R Equivalent to --readonly in the main description. -select use a LOG SELECT command. Equivalent to --select in the main de- scription. -sp sets the Saving Parameters (SP) bit. Default is 0 (i.e. cleared). Equivalent to --sp in the main description. -t outputs the temperature. Equivalent to --temperature in the main de- scription. -T outputs the transport ('Protocol specific port') log page. Equiva- lent to --transport in the main description. -v increase level of verbosity. -V print out version string then exit. -x suppress the INQUIRY command. Equivalent to --no_inq in the main de- scription. -? output usage message then exit. ENVIRONMENT VARIABLES Since sg3_utils version 1.23 the environment variable SG3_UTILS_OLD_OPTS can be given. When it is present this utility will expect the older command line options. So the presence of this environment variable is equivalent to using --old (or -O) as the first command line option. AUTHOR Written by Douglas Gilbert REPORTING BUGS Report bugs to <dgilbert at interlog dot com>. COPYRIGHT Copyright (C) 2002-2023 Douglas Gilbert This software is distributed under the GPL version 2. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. SEE ALSO smartctl(smartmontools), sg_senddiag(8) sg3_utils-1.48 May 2023 SG_LOGS(8)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | LOG SELECT | APPLICATION CLIENT | INHEX INSTEAD OF DEVICE | NOTES | EXIT STATUS | OLDER COMMAND LINE OPTIONS | ENVIRONMENT VARIABLES | AUTHOR | REPORTING BUGS | COPYRIGHT | SEE ALSO
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=sg_logs&sektion=8&manpath=FreeBSD+Ports+15.1.quarterly>