FreeBSD Manual Pages
VDMFEC(1) General Commands Manual VDMFEC(1) NAME vdmfec - Block ECC for files SYNOPSIS vdmfec [-v] [-d] [-b blocksize] [-n N] [-k K] [file] vdm_encode [-v] [-b blocksize] [-n N] [-k K] [file] vdm_decode [-v] [-b blocksize] [-n N] [-k K] [file] DESCRIPTION vdmfec reads an input stream and adds error correction blocks so that large consecutive sections of the output stream may be corrupted, and the data recovered. For example, diskettes typically lose whole sectors at once, or related groups of sectors, or even entire tracks. Data written to a diskette with this program may be recovered even with many read errors. The algorithm used is a Forward Error Correction (FEC) code based on Van- dermonde (VDM) matrices in GF(2^8) due to Luigi Rizzo. Given the FEC para- meters K and N, with N greater than K, N blocks are written for every K in- put blocks in such a way that any K blocks are sufficient to reconstruct the data. That is, up to N - K blocks out of every group of N blocks may be lost without loss of data. The amount of overhead in the output stream is easily adjustable by varying K. N and blocksize control the total amount of data written. Depending on the types of errors you expect, different settings may be more or less use- ful. For example, you may not expect to have two or three bad sectors on every track (if you do it's time to replace the diskette!), but you might expect three bad sectors on two or three contiguous tracks (diskette errors tend to cluster). OPTIONS -v Print informative messages about the encoding or decoding process to stderr, including the expansion factor. Use -vv to get information about each block being read or written. -d Decode the input rather than encoding it. Using this option is equivalent to invoking the program as vdm_decode. -b blocksize Set the FEC block size to blocksize bytes. The blocksize may have a 'k' or 'K' appended, in which case the block size is set to block- size * 1024 bytes. This should usually be a multiple of the output media block or sector size (e.g., 512, 1024, 18K, etc.), and must be at least 26 bytes in version 1. Default 1024. -n N -k K Set the FEC N and K parameters. N must be greater than 2 and less than or equal to 256. K must be greater than 0 and less than N. Default N=18, K=14. Note that the N, K, and blocksize parameters are NOT written to the output! You must specify the same parameters when you run the decoder. (Actually, the decoder is capable of explicitly detecting an invalid K value, but in- correct blocksize or N values will result in bad blocks and decode fail- ure.) The decoder is capable of reading from non-seekable media such as pipes, however, buffer underruns are not detected and will result in failure. Also, when reading from a pipe the entire file must be read. Reading from a seek-able stream can be faster because only K good blocks out of N need to be read. The encoder stores chunk and block ids which are used to detect out of or- der blocks, but those errors (which can sometimes happen due to filesystem corruption) are not corrected. The only type of error that can be cor- rected is in place corruption of data. In particular, missing blocks (as from lost packets) result in decode failure, even when K good blocks are available. This program is primarily intended to recover data lost due to read errors on fixed media such as diskettes; several other programs and libraries are available that use FEC to handle the other (typically network packet) errors. EXAMPLES Consider a diskette with 80 tracks, 2 heads, and 18 512-byte sectors per track (a standard 1.44MB diskette). bzip2 < file | vdmfec > /dev/fd0 uses the default parameters of -b1k -n18 -k14, stores up to ~1.1MB of com- pressed input data, written one (double-sided) track (18K) at a time, and allows 4 bad clusters (8 sectors) per track. vdmfec -d /dev/fd0 | bunzip2 > file recovers the original file. vdm_encode -b18k -n80 -k70 file.img > /dev/fd0 writes the entire diskette, stores up to ~1.23MB of data, and allows multi- ple errors on 10 different double-sided tracks. vdm_decode -b18k -n80 -k70 /dev/fd0 > file.img recovers the data and reads no less than 70 tracks. Note that vdm_decode exits with a non-zero status on failure, so that constructions such as vdm_decode /dev/fd0 > moo && tar -xvf moo are possible. dd if=/dev/tape ibs=1024 conv=noerror,sync | \ vdm_decode > file This might be necessary to recover data from some non-seekable media. You can of course simply write the encoded output to a normal file, as in tar -cf - dir | gzip | vdm_encode -v > dir.tgz.vdm REPORTING BUGS Report bugs to Tom Holroyd <tomh@po.crl.go.jp>. SEE ALSO fec(3) vdmfec September 2001 VDMFEC(1)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | EXAMPLES | REPORTING BUGS | SEE ALSO
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=vdmfec&sektion=1&manpath=FreeBSD+Ports+15.1.quarterly>