FreeBSD Manual Pages
SPI(8) System Manager's Manual SPI(8) NAME spi -- communicate on SPI bus with slave devices SYNOPSIS spi [-A] [-b] [-L] [-v] [-C command-bytes] [-c count] [-d r|w|rw] [-f device] [-m mode] [-s max-speed] spi [-i] [-v] [-f device] spi [-h] DESCRIPTION The spi utility can be used to perform raw data transfers (read, write, or simultaneous read/write) with devices on the SPI bus, via the spigen(4) device. Each spigen(4) device is associated with a specific "chip select" (cs) pin on the spibus, and therefore needs to be specified. If no device name is specified on the command line, spi assumes "spigen0.0". For more information on the spigen device, see spigen(4). The options are as follows: -A Specifies ASCII mode. Both read and write data is input and output as 2-character hexadecimal values, optionally sepa- rated by white space, such as 00 01 02 etc. When combined with the -b flag, the data on stdin remains a sequence of ASCII hexadecimal byte values, but the output reverts to bi- nary mode. -b Binary (output) mode. Only has an effect when -A has been specified. Reverts the output back to binary (rather than ASCII), while leaving the input format as-is. Use in combi- nation with -A to allow using something like "echo" to pass hexadecimal values to the SPI device, but output the re- ceived data on stdout as binary. -C command-bytes Sends one or more command bytes, skipping any bytes read-in during the transfer. The byte values should be specified as a quoted parameter, similar to the format for data on stdin for -A, that is, 2 character hexadecimal values, optionally separated by white space. An SPI device will typically re- quire that a command be sent, followed by bytes of data. You can use this option to send the command without receiv- ing any data bytes during the command sequence. -c count The total number of bytes to transfer as a decimal integer. If a write or a read/write transaction is being performed, and fewer than this number of bytes are read in from stdin, the remaining bytes will be sent with a value of "0". If the length can be determined from the input file size, you can use a count value of "-1" to base the transfer on the input file's size. -d r|w|rw Transfer direction: Use r for read, w for write, and rw for simultaneous read and write. -f device SPI device to use (default is /dev/spigen0). -h Print help text to stderr, explaining the command line op- tions. -i Displays information about the SPI device to stderr. When- ever this flag is specified, no data is read or written, and the mode and clock speed are not changed. -L LSB bit order. The default is MSB, i.e., the highest order bit is transmitted first. Specifying -L caused the LSB to be transmitted and read first. -m 0|1|2|3 SPI mode, 0 through 3. This defines the clock phase and timing with respect to reading and writing data, as per the SPI specification. -s speed Specify the maximum speed, in Hz, for the SPI clock. The bus will operate at its highest available speed which does not exceed this maximum. -v Specifies Verbose mode. Diagnostics and information are written to stderr. You can specify -v more than once to in- crease verbosity. EXAMPLES Here are a few examples of using the spi utility: • Get information about the default SPI device spi -i • Set the maximum clock speed to 200Khz and the mode to 3 on spi- gen0.1, but do not transmit nor receive any data spi -f spigen0.1 -s 200000 -m 3 • Send a command sequence consisting of 2 bytes, and read 2 addi- tional bytes from the SPI device, using the current mode and speed on the default device spi -d r -C "00 01" -c 2 • Transmit a byte value of 5, and receive 2 bytes, displaying their values as 2-byte ASCII hexadecimal, with mode 2, and a maximum clock speed of 500khz. echo "05" | spi -A -d rw -m 2 -s 500000 -c 2 • Send a binary file, and output the SPI result through od(1) as hexadecimal bytes, using the current maximum clock speed and SPI mode. spi -d rw -c -1 <input_file.bin | od -An -t x1 • Send 2 bytes of data, receive a total of 4 bytes, and output the SPI result as binary data, piped through od(1), displaying it as two hexadecimal unsigned short integer values. echo "00 01" | spi -A -b -d rw -c 4 | od -t x2 • Query the manufacturer ID and size from a standard spiflash device, by sending the command byte 0x9f and displaying the 3-byte reply in ASCII hex. spi -f spigen0.0 -m 0 -s 1000000 -d r -c 3 -A -C 9f SEE ALSO spigen(4) HISTORY The spi utility appeared in FreeBSD 11.3. FreeBSD 14.3 August 21, 2020 SPI(8)
NAME | SYNOPSIS | DESCRIPTION | EXAMPLES | SEE ALSO | HISTORY
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=spi&sektion=8&manpath=FreeBSD+14.3-RELEASE+and+Ports>