FreeBSD Manual Pages
BUILD(7) Miscellaneous Information Manual BUILD(7) NAME build -- information on how to build the system DESCRIPTION The sources for the FreeBSD system and its applications are contained in three different directories, normally /usr/src, /usr/doc, and /usr/ports. These directories may be initially empty or non-existent until updated with svn(1) or portsnap(8). Directory /usr/src contains the "base system" sources, which is loosely defined as the things re- quired to rebuild the system to a useful state. Directory /usr/doc contains the source for the system documentation, excluding the manual pages. Directory /usr/ports contains a tree that provides a consistent interface for building and installing third party applications. For more information about the ports build process, see ports(7). The make(1) command is used in each of these directories to build and install the things in that directory. Issuing the make(1) command in any directory or subdirectory of those directories has the same effect as issuing the same command in all subdirectories of that directory. With no target specified, the things in that directory are just built. A source tree is allowed to be read-only. As described in make(1), ob- jects are usually built in a separate object directory hierarchy speci- fied by the environment variable MAKEOBJDIRPREFIX, or under /usr/obj if variable MAKEOBJDIRPREFIX is not set. For a given source directory, its canonical object directory would be ${MAKEOBJDIRPREFIX}${.CURDIR} if make(1) variable MAKEOBJDIRPREFIX is set, or /usr/obj${.CURDIR} if this variable is not set. Cross-builds set the object directory as de- scribed in the documentation for the buildworld target below. The build may be controlled by defining make(1) variables described in the "ENVIRONMENT" section below, and by the variables documented in make.conf(5). The following list provides the names and actions for the targets sup- ported by the build system: clean Remove any files created during the build process. cleandepend Remove the file ${.OBJDIR}/${DEPENDFILE} generated by a prior "make depend" step. cleandir Remove the canonical object directory if it exists, or perform actions equivalent to "make clean cleandepend" if it does not. This target will also remove an obj link in ${.CURDIR} if that exists. It is advisable to run "make cleandir" twice: the first invocation will remove the canonical object directory and the second one will clean up ${.CURDIR}. depend Generate a list of build dependencies in file ${.OBJDIR}/${DEPENDFILE}. install Install the results of the build to the appropriate loca- tion in the installation directory hierarchy specified in variable DESTDIR. obj Create the canonical object directory associated with the current directory. objlink Create a symbolic link to the canonical object directory in ${.CURDIR}. tags Generate a tags file using the program specified in the make(1) variable CTAGS. The build system supports ctags(1) and GNU Global. The other supported targets under directory /usr/src are: buildenv Spawn an interactive shell with environment variables set up for cross-building the system. The target ar- chitecture needs to be specified with make(1) vari- ables TARGET_ARCH and TARGET. This target is only useful after a complete cross- toolchain including the compiler, linker, assembler, headers and libraries has been built; see the toolchain target below. buildworld Build everything but the kernel, configure files in etc, and release. The actual build location prefix used is ${MAKEOBJDIRPREFIX}${.CURDIR} for native builds, and ${MAKEOBJDIRPREFIX}/${TARGET}${.CURDIR} for cross builds and native builds with variable CROSS_BUILD_TESTING set. cleanworld Attempt to clean up targets built by a preceding buildworld step. distributeworld Distribute everything compiled by a preceding buildworld step. Files are placed in the directory hierarchy specified by make(1) variable DISTDIR. This target is used while building a release; see release(7). packageworld Archive the results of distributeworld, placing the results in DISTDIR. This target is used while build- ing a release; see release(7). installworld Install everything built by a preceding buildworld step into the directory hierarchy pointed to by make(1) variable DESTDIR. If installing onto an NFS file system and running make(1) with the -j option, make sure that rpc.lockd(8) is running on both client and server. See rc.conf(5) on how to make it start at boot time. toolchain Create the build toolchain needed to build the rest of the system. For cross-architecture builds, this step creates a cross-toolchain. universe For each architecture, execute a buildworld followed by a buildkernel for all kernels for that architec- ture, including LINT. This command takes a long time. update Get updated sources as configured in make.conf(5). targets Print a list of supported TARGET / TARGET_ARCH pairs for world and kernel targets. tinderbox Execute the same targets as universe. In addition print a summary of all failed targets at the end and exit with an error if there were any. toolchains Create a build toolchain for each architecture sup- ported by the build system. Kernel specific build targets in /usr/src are: buildkernel Rebuild the kernel and the kernel modules. installkernel Install the kernel and the kernel modules to direc- tory ${DESTDIR}/boot/kernel, renaming any pre-exist- ing directory with this name to kernel.old if it con- tained the currently running kernel. The target di- rectory under ${DESTDIR} may be modified using the INSTKERNNAME and KODIR make(1) variables. distributekernel Install the kernel to the directory ${DISTDIR}/kernel/boot/kernel. This target is used while building a release; see release(7). packagekernel Archive the results of distributekernel, placing the results in DISTDIR. This target is used while build- ing a release; see release(7). kernel Equivalent to buildkernel followed by installkernel kernel-toolchain Rebuild the tools needed for kernel compilation. Use this if you did not do a buildworld first. reinstallkernel Reinstall the kernel and the kernel modules, over- writing the contents of the target directory. As with the installkernel target, the target directory can be specified using the make(1) variable INSTKERNNAME. Convenience targets for cleaning up the install destination directory denoted by variable DESTDIR include: check-old Print a list of old files and directories in the sys- tem. delete-old Delete obsolete base system files and directories in- teractively. When -DBATCH_DELETE_OLD_FILES is speci- fied at the command line, the delete operation will be non-interactive. The variables DESTDIR, TARGET_ARCH and TARGET should be set as with "make installworld". delete-old-libs Delete obsolete base system libraries interactively. This target should only be used if no 3rd party soft- ware uses these libraries. When -DBATCH_DELETE_OLD_FILES is specified at the command line, the delete operation will be non-interactive. The variables DESTDIR, TARGET_ARCH and TARGET should be set as with "make installworld". ENVIRONMENT Variables that influence all builds include: DEBUG_FLAGS Defines a set of debugging flags that will be used to build all userland binaries under /usr/src. When DEBUG_FLAGS is defined, the install and installworld targets install binaries from the current MAKEOBJDIRPREFIX without stripping, so that debugging information is retained in the installed binaries. DESTDIR The directory hierarchy prefix where built objects will be installed. If not set, DESTDIR defaults to the empty string. MAKEOBJDIRPREFIX Defines the prefix for directory names in the tree of built objects. Defaults to /usr/obj if not defined. This variable should only be set in the environment and not via /etc/make.conf or the command line. NO_WERROR If defined, compiler warnings will not cause the build to halt, even if the makefile says otherwise. WITH_CTF If defined, the build process will run the DTrace CTF conversion tools on built objects. Additionally, builds in /usr/src are influenced by the following make(1) variables: KERNCONF Overrides which kernel to build and install for the various kernel make targets. It defaults to GENERIC. KERNFAST If set, the build target buildkernel defaults to set- ting NO_KERNELCLEAN, NO_KERNELCONFIG, NO_KERNELDEPEND and NO_KERNELOBJ. When set to a value other than 1 then KERNCONF is set to the value of KERNFAST. LOCAL_DIRS If set, this variable supplies a list of additional directories relative to the root of the source tree to build as part of the everything target. LOCAL_ITOOLS If set, this variable supplies a list of additional tools that are used by the installworld and distributeworld targets. LOCAL_LIB_DIRS If set, this variable supplies a list of additional directories relative to the root of the source tree to build as part of the libraries target. LOCAL_MTREE If set, this variable supplies a list of additional mtrees relative to the root of the source tree to use as part of the hierarchy target. LOCAL_TOOL_DIRS If set, this variable supplies a list of additional directories relative to the root of the source tree to build as part of the build-tools target. PORTS_MODULES A list of ports with kernel modules that should be built and installed as part of the buildkernel and installkernel process. make PORTS_MODULES=emulators/kqemu-kmod kernel STRIPBIN Command to use at install time when stripping bina- ries. Be sure to add any additional tools required to run STRIPBIN to the LOCAL_ITOOLS make(1) variable be- fore running the distributeworld or installworld tar- gets. See install(1) for more details. SUBDIR_OVERRIDE Override the default list of sub-directories and only build the sub-directory named in this variable. This variable is useful when debugging failed builds. make some-target SUBDIR_OVERRIDE=foo/bar TARGET The target hardware platform. This is analogous to the "uname -m" output. This is necessary to cross- build some target architectures. For example, cross- building for PC98 machines requires TARGET_ARCH=i386 and TARGET=pc98. If not set, TARGET defaults to the current hardware platform. TARGET_ARCH The target machine processor architecture. This is analogous to the "uname -p" output. Set this to cross-build for a different architecture. If not set, TARGET_ARCH defaults to the current machine architec- ture, unless TARGET is also set, in which case it de- faults to the appropriate value for that platform. Typically, one only needs to set TARGET. Builds under directory /usr/src are also influenced by defining one or more of the following symbols, using the -D option of make(1): NO_CLEANDIR If set, the build targets that clean parts of the object tree use the equivalent of "make clean" in- stead of "make cleandir". NO_CLEAN If set, no object tree files are cleaned at all. Setting NO_CLEAN implies NO_KERNELCLEAN, so when NO_CLEAN is set no kernel objects are cleaned ei- ther. NO_CTF If set, the build process does not run the DTrace CTF conversion tools on built objects. NO_SHARE If set, the build does not descend into the /usr/src/share subdirectory (i.e., manpages, locale data files, timezone data files and other /usr/src/share files will not be rebuild from their sources). NO_KERNELCLEAN If set, the build process does not run "make clean" as part of the buildkernel target. NO_KERNELCONFIG If set, the build process does not run config(8) as part of the buildkernel target. NO_KERNELDEPEND If set, the build process does not run "make depend" as part of the buildkernel target. NO_KERNELOBJ If set, the build process does not run "make obj" as part of the buildkernel target. NO_DOCUPDATE If set, the update process does not update the source of the FreeBSD documentation as part of the "make update" target. NO_PORTSUPDATE If set, the update process does not update the Ports tree as part of the "make update" target. NO_WWWUPDATE If set, the update process does not update the www tree as part of the "make update" target. Builds under directory /usr/doc are influenced by the following make(1) variables: DOC_LANG If set, restricts the documentation build to the language subdirectories specified as its content. The default action is to build documentation for all languages. Builds using the universe target are influenced by the following make(1) variables: JFLAG Pass the value of this variable to each make(1) in- vocation used to build worlds and kernels. This can be used to enable multiple jobs within a single ar- chitecture's build while still building each archi- tecture serially. MAKE_JUST_KERNELS Only build kernels for each supported architecture. MAKE_JUST_WORLDS Only build worlds for each supported architecture. UNIVERSE_TARGET Execute the specified make(1) target for each sup- ported architecture instead of the default action of building a world and one or more kernels. FILES /usr/doc/Makefile /usr/doc/share/mk/doc.project.mk /usr/ports/Mk/bsd.port.mk /usr/ports/Mk/bsd.sites.mk /usr/share/examples/etc/make.conf /usr/src/Makefile /usr/src/Makefile.inc1 EXAMPLES For an "approved" method of updating your system from the latest sources, please see the "COMMON ITEMS" section in src/UPDATING. The following sequence of commands can be used to cross-build the sys- tem for the sparc64 architecture on an i386 host: cd /usr/src make TARGET=sparc64 buildworld make TARGET=sparc64 DESTDIR=/clients/sparc64 installworld SEE ALSO cc(1), install(1), make(1), svn(1), make.conf(5), src.conf(5), ports(7), release(7), config(8), mergemaster(8), portsnap(8), reboot(8), shutdown(8) AUTHORS Mike W. Meyer <mwm@mired.org>. GNU January 4, 2015 BUILD(7)
NAME | DESCRIPTION | ENVIRONMENT | FILES | EXAMPLES | SEE ALSO | AUTHORS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=build&sektion=7&manpath=FreeBSD+10.2-RELEASE>