FreeBSD Manual Pages
CP(1) FreeBSD General Commands Manual CP(1) NAME cp -- copy files SYNOPSIS cp [-R [-H | -L | -P]] [-f | -i | -n] [-alpsvx] source_file target_file cp [-R [-H | -L | -P]] [-f | -i | -n] [-alpsvx] source_file ... target_directory cp [-f | -i | -n] [-alPpsvx] source_file target_file cp [-f | -i | -n] [-alPpsvx] source_file ... target_directory DESCRIPTION In the first synopsis form, the cp utility copies the contents of the source_file to the target_file. In the second synopsis form, the con- tents of each named source_file is copied to the destination target_directory. The names of the files themselves are not changed. If cp detects an attempt to copy a file to itself, the copy will fail. The following options are available: -H If the -R option is specified, symbolic links on the command line are followed. (Symbolic links encountered in the tree traversal are not followed.) -L If the -R option is specified, all symbolic links are followed. -P No symbolic links are followed. This is the default if the -R op- tion is specified. -R If source_file designates a directory, cp copies the directory and the entire subtree connected at that point. If the source_file ends in a /, the contents of the directory are copied rather than the directory itself. This option also causes symbolic links to be copied, rather than indirected through, and for cp to create spe- cial files rather than copying them as normal files. Created di- rectories have the same mode as the corresponding source directory, unmodified by the process' umask. Note that cp copies hard linked files as separate files. If you need to preserve hard links, consider using tar(1), cpio(1), or pax(1) instead. -a Archive mode. Same as -RpP. -f For each existing destination pathname, remove it and create a new file, without prompting for confirmation regardless of its permis- sions. (The -f option overrides any previous -i or -n options.) -i Cause cp to write a prompt to the standard error output before copying a file that would overwrite an existing file. If the re- sponse from the standard input begins with the character `y' or `Y', the file copy is attempted. (The -i option overrides any pre- vious -f or -n options.) -l Create hard links to regular files in a hierarchy instead of copy- ing. -n Do not overwrite an existing file. (The -n option overrides any previous -f or -i options.) -p Cause cp to preserve the following attributes of each source file in the copy: modification time, access time, file flags, file mode, ACL, user ID, and group ID, as allowed by permissions. If the user ID and group ID cannot be preserved, no error message is displayed and the exit value is not altered. If the source file has its set-user-ID bit on and the user ID can- not be preserved, the set-user-ID bit is not preserved in the copy's permissions. If the source file has its set-group-ID bit on and the group ID cannot be preserved, the set-group-ID bit is not preserved in the copy's permissions. If the source file has both its set-user-ID and set-group-ID bits on, and either the user ID or group ID cannot be preserved, neither the set-user-ID nor set- group-ID bits are preserved in the copy's permissions. -s Create symbolic links to regular files in a hierarchy instead of copying. -v Cause cp to be verbose, showing files as they are copied. -x File system mount points are not traversed. For each destination file that already exists, its contents are overwrit- ten if permissions allow. Its mode, user ID, and group ID are unchanged unless the -p option was specified. In the second synopsis form, target_directory must exist unless there is only one named source_file which is a directory and the -R flag is speci- fied. If the destination file does not exist, the mode of the source file is used as modified by the file mode creation mask (umask, see csh(1)). If the source file has its set-user-ID bit on, that bit is removed unless both the source file and the destination file are owned by the same user. If the source file has its set-group-ID bit on, that bit is removed un- less both the source file and the destination file are in the same group and the user is a member of that group. If both the set-user-ID and set- group-ID bits are set, all of the above conditions must be fulfilled or both bits are removed. Appropriate permissions are required for file creation or overwriting. Symbolic links are always followed unless the -R flag is set, in which case symbolic links are not followed, by default. The -H or -L flags (in conjunction with the -R flag) cause symbolic links to be followed as de- scribed above. The -H, -L and -P options are ignored unless the -R op- tion is specified. In addition, these options override each other and the command's actions are determined by the last one specified. If cp receives a SIGINFO (see the status argument for stty(1)) signal, the current input and output file and the percentage complete will be written to the standard output. EXIT STATUS The cp utility exits 0 on success, and >0 if an error occurs. EXAMPLES Make a copy of file foo named bar: $ cp foo bar Copy a group of files to the /tmp directory: $ cp *.txt /tmp Copy the directory junk and all of its contents (including any subdirec- tories) to the /tmp directory: $ cp -R junk /tmp COMPATIBILITY Historic versions of the cp utility had a -r option. This implementation supports that option, however, its behavior is different from historical FreeBSD behavior. Use of this option is strongly discouraged as the be- havior is implementation-dependent. In FreeBSD, -r is a synonym for -RL and works the same unless modified by other flags. Historical implemen- tations of -r differ as they copy special files as normal files while recreating a hierarchy. The -l, -s, -v, -x and -n options are non-standard and their use in scripts is not recommended. SEE ALSO mv(1), rcp(1), umask(2), fts(3), symlink(7) STANDARDS The cp command is expected to be IEEE Std 1003.2 ("POSIX.2") compatible. HISTORY A cp command appeared in Version 1 AT&T UNIX. FreeBSD 13.0 February 23, 2022 FreeBSD 13.0
NAME | SYNOPSIS | DESCRIPTION | EXIT STATUS | EXAMPLES | COMPATIBILITY | SEE ALSO | STANDARDS | HISTORY
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=cp&manpath=FreeBSD+13.2-RELEASE+and+Ports>