FreeBSD Manual Pages
DNSMASQ(8) System Manager's Manual DNSMASQ(8) NAME dnsmasq - A lightweight DHCP and caching DNS server. SYNOPSIS dnsmasq [OPTION]... DESCRIPTION dnsmasq is a lightweight DNS, TFTP, PXE, router advertisement and DHCP server. It is intended to provide coupled DNS and DHCP service to a LAN. Dnsmasq accepts DNS queries and either answers them from a small, lo- cal, cache or forwards them to a real, recursive, DNS server. It loads the contents of /etc/hosts so that local hostnames which do not appear in the global DNS can be resolved and also answers DNS queries for DHCP configured hosts. It can also act as the authoritative DNS server for one or more domains, allowing local names to appear in the global DNS. It can be configured to do DNSSEC validation. The dnsmasq DHCP server supports static address assignments and multi- ple networks. It automatically sends a sensible default set of DHCP op- tions, and can be configured to send any desired set of DHCP options, including vendor-encapsulated options. It includes a secure, read-only, TFTP server to allow net/PXE boot of DHCP hosts and also supports BOOTP. The PXE support is full featured, and includes a proxy mode which supplies PXE information to clients whilst DHCP address alloca- tion is done by another server. The dnsmasq DHCPv6 server provides the same set of features as the DHCPv4 server, and in addition, it includes router advertisements and a neat feature which allows naming for clients which use DHCPv4 and stateless autoconfiguration only for IPv6 configuration. There is sup- port for doing address allocation (both DHCPv6 and RA) from subnets which are dynamically delegated via DHCPv6 prefix delegation. Dnsmasq is coded with small embedded systems in mind. It aims for the smallest possible memory footprint compatible with the supported func- tions, and allows unneeded functions to be omitted from the compiled binary. OPTIONS Note that in general missing parameters are allowed and switch off functions, for instance "--pid-file" disables writing a PID file. On BSD, unless the GNU getopt library is linked, the long form of the op- tions does not work on the command line; it is still recognised in the configuration file. --test Read and syntax check configuration file(s). Exit with code 0 if all is OK, or a non-zero code otherwise. Do not start up dns- masq. -w, --help Display all command-line options. --help dhcp will display known DHCPv4 configuration options, and --help dhcp6 will dis- play DHCPv6 options. -h, --no-hosts Don't read the hostnames in /etc/hosts. -H, --addn-hosts=<file> Additional hosts file. Read the specified file as well as /etc/hosts. If --no-hosts is given, read only the specified file. This option may be repeated for more than one additional hosts file. If a directory is given, then read all the files contained in that directory in alphabetical order. --hostsdir=<path> Read all the hosts files contained in the directory. New or changed files are read automatically and modified and deleted files have removed records automatically deleted. -E, --expand-hosts Add the domain to simple names (without a period) in /etc/hosts in the same way as for DHCP-derived names. Note that this does not apply to domain names in cnames, PTR records, TXT records etc. -T, --local-ttl=<time> When replying with information from /etc/hosts or configuration or the DHCP leases file dnsmasq by default sets the time-to-live field to zero, meaning that the requester should not itself cache the information. This is the correct thing to do in almost all situations. This option allows a time-to-live (in seconds) to be given for these replies. This will reduce the load on the server at the expense of clients using stale data under some circumstances. --dhcp-ttl=<time> As for --local-ttl, but affects only replies with information from DHCP leases. If both are given, --dhcp-ttl applies for DHCP information, and --local-ttl for others. Setting this to zero eliminates the effect of --local-ttl for DHCP. --neg-ttl=<time> Negative replies from upstream servers normally contain time-to- live information in SOA records which dnsmasq uses for caching. If the replies from upstream servers omit this information, dns- masq does not cache the reply. This option gives a default value for time-to-live (in seconds) which dnsmasq uses to cache nega- tive replies even in the absence of an SOA record. --max-ttl=<time> Set a maximum TTL value that will be handed out to clients. The specified maximum TTL will be given to clients instead of the true TTL value if it is lower. The true TTL value is however kept in the cache to avoid flooding the upstream DNS servers. --max-cache-ttl=<time> Set a maximum TTL value for entries in the cache. --min-cache-ttl=<time> Extend short TTL values to the time given when caching them. Note that artificially extending TTL values is in general a bad idea, do not do it unless you have a good reason, and understand what you are doing. Dnsmasq limits the value of this option to one hour, unless recompiled. --auth-ttl=<time> Set the TTL value returned in answers from the authoritative server. --fast-dns-retry=[<initial retry delay in ms>[,<time to continue re- tries in ms>]] Under normal circumstances, dnsmasq relies on DNS clients to do retries; it does not generate timeouts itself. Setting this op- tion instructs dnsmasq to generate its own retries starting af- ter a delay which defaults to 1000ms. If the second parameter is given this controls how long the retries will continue for oth- erwise this defaults to 10000ms. Retries are repeated with expo- nential backoff. Using this option increases memory usage and network bandwidth. If not otherwise configured, this option is activated with the default parameters when --dnssec is set. -k, --keep-in-foreground Do not go into the background at startup but otherwise run as normal. This is intended for use when dnsmasq is run under dae- montools or launchd. -d, --no-daemon Debug mode: don't fork to the background, don't write a pid file, don't change user id, generate a complete cache dump on receipt on SIGUSR1, log to stderr as well as syslog, don't fork new processes to handle TCP queries. Note that this option is for use in debugging only, to stop dnsmasq daemonising in pro- duction, use --keep-in-foreground. -q, --log-queries Log the results of DNS queries handled by dnsmasq. Enable a full cache dump on receipt of SIGUSR1. If the argument "extra" is supplied, ie --log-queries=extra then the log has extra informa- tion at the start of each line. This consists of a serial num- ber which ties together the log lines associated with an indi- vidual query, and the IP address of the requestor. If the argu- ment "proto" is supplied, this shows everything that "extra" does and also the network protocol used to communicate the queries. Logging of only queries to the authoritative server can be configured with --log-queries=auth and logging only failed replies (Error, NXDOMAIN or NODATA) can be configured with --log-queries=only_failed -8, --log-facility=<facility> Set the facility to which dnsmasq will send syslog entries, this defaults to DAEMON, and to LOCAL0 when debug mode is in opera- tion. If the facility given contains at least one '/' character, it is taken to be a filename, and dnsmasq logs to the given file, instead of syslog. If the facility is '-' then dnsmasq logs to stderr. (Errors whilst reading configuration will still go to syslog, but all output from a successful startup, and all output whilst running, will go exclusively to the file.) When logging to a file, dnsmasq will close and reopen the file when it receives SIGUSR2. This allows the log file to be rotated without stopping dnsmasq. --log-debug Enable extra logging intended for debugging rather than informa- tion. --log-async[=<lines>] Enable asynchronous logging and optionally set the limit on the number of lines which will be queued by dnsmasq when writing to the syslog is slow. Dnsmasq can log asynchronously: this allows it to continue functioning without being blocked by syslog, and allows syslog to use dnsmasq for DNS queries without risking deadlock. If the queue of log-lines becomes full, dnsmasq will log the overflow, and the number of messages lost. The default queue length is 5, a sane value would be 5-25, and a maximum limit of 100 is imposed. -x, --pid-file=<path> Specify an alternate path for dnsmasq to record its process-id in. Normally /var/run/dnsmasq.pid. -u, --user=<username> Specify the userid to which dnsmasq will change after startup. Dnsmasq must normally be started as root, but it will drop root privileges after startup by changing id to another user. Nor- mally this user is "nobody" but that can be over-ridden with this switch. -g, --group=<groupname> Specify the group which dnsmasq will run as. The default is "dip", if available, to facilitate access to /etc/ppp/re- solv.conf which is not normally world readable. -v, --version Print the version number. -p, --port=<port> Listen on <port> instead of the standard DNS port (53). Setting this to zero completely disables DNS function, leaving only DHCP and/or TFTP. -P, --edns-packet-max=<size> Specify the largest EDNS.0 UDP packet which is supported by the DNS forwarder. Defaults to 1232, which is the recommended size following the DNS flag day in 2020. Only increase if you know what you are doing. -Q, --query-port=<query_port> Send outbound DNS queries from, and listen for their replies on, the specific UDP port <query_port> instead of using random ports. NOTE that using this option will make dnsmasq less secure against DNS spoofing attacks but it may be faster and use less resources. Setting this option to zero makes dnsmasq use a sin- gle port allocated to it by the OS: this was the default behav- iour in versions prior to 2.43. --port-limit=<#ports> By default, when sending a query via random ports to multiple upstream servers or retrying a query dnsmasq will use a single random port for all the tries/retries. This option allows a larger number of ports to be used, which can increase robustness in certain network configurations. Note that increasing this to more than two or three can have security and resource implica- tions and should only be done with understanding of those. --min-port=<port> Do not use ports less than that given as source for outbound DNS queries. Dnsmasq picks random ports as source for outbound queries: when this option is given, the ports used will always be larger than that specified. Useful for systems behind fire- walls. If not specified, defaults to 1024. --max-port=<port> Use ports lower than that given as source for outbound DNS queries. Dnsmasq picks random ports as source for outbound queries: when this option is given, the ports used will always be lower than that specified. Useful for systems behind fire- walls. -i, --interface=<interface name> Listen only on the specified interface(s). Dnsmasq automatically adds the loopback (local) interface to the list of interfaces to use when the --interface option is used. If no --interface or --listen-address options are given dnsmasq listens on all avail- able interfaces except any given in --except-interface options. On Linux, when --bind-interfaces or --bind-dynamic are in ef- fect, IP alias interface labels (eg "eth1:0") are checked, rather than interface names. In the degenerate case when an in- terface has one address, this amounts to the same thing but when an interface has multiple addresses it allows control over which of those addresses are accepted. The same effect is achievable in default mode by using --listen-address. A simple wildcard, consisting of a trailing '*', can be used in --interface and --except-interface options. -I, --except-interface=<interface name> Do not listen on the specified interface. Note that the order of --listen-address --interface and --except-interface options does not matter and that --except-interface options always override the others. The comments about interface labels for --listen-ad- dress apply here. --auth-server=<domain>,[<interface>|<ip-address>...] Enable DNS authoritative mode for queries arriving at an inter- face or address. Note that the interface or address need not be mentioned in --interface or --listen-address configuration, in- deed --auth-server will override these and provide a different DNS service on the specified interface. The <domain> is the "glue record". It should resolve in the global DNS to an A and/or AAAA record which points to the address dnsmasq is lis- tening on. When an interface is specified, it may be qualified with "/4" or "/6" to specify only the IPv4 or IPv6 addresses as- sociated with the interface. Since any defined authoritative zones are also available as part of the normal recusive DNS ser- vice supplied by dnsmasq, it can make sense to have an --auth- server declaration with no interfaces or address, but simply specifying the primary external nameserver. --local-service[=net|host] Without parameter or with net parameter, restricts service to connected network. Accept DNS queries only from hosts whose ad- dress is on a local subnet, ie a subnet for which an interface exists on the server. With host parameter, listens only on lo interface and accepts queries from localhost only. This option only has effect if there are no --interface, --except-interface, --listen-address or --auth-server options. It is intended to be set as a default on installation, to allow unconfigured instal- lations to be useful but also safe from being used for DNS am- plification attacks. -2, --no-dhcp-interface=<interface name> Do not provide DHCP, TFTP or router advertisement on the speci- fied interface, but do provide DNS service. --no-dhcpv4-interface=<interface name> Disable only IPv4 DHCP on the specified interface. --no-dhcpv6-interface=<interface name> Disable IPv6 DHCP and router advertisement on the specified in- terface. -a, --listen-address=<ipaddr> Listen on the given IP address(es). Both --interface and --lis- ten-address options may be given, in which case the set of both interfaces and addresses is used. Note that if no --interface option is given, but --listen-address is, dnsmasq will not auto- matically listen on the loopback interface. To achieve this, its IP address, 127.0.0.1, must be explicitly given as a --listen- address option. -z, --bind-interfaces On systems which support it, dnsmasq binds the wildcard address, even when it is listening on only some interfaces. It then dis- cards requests that it shouldn't reply to. This has the advan- tage of working even when interfaces come and go and change ad- dress. This option forces dnsmasq to really bind only the inter- faces it is listening on. About the only time when this is use- ful is when running another nameserver (or another instance of dnsmasq) on the same machine. Setting this option also enables multiple instances of dnsmasq which provide DHCP service to run in the same machine. --bind-dynamic Enable a network mode which is a hybrid between --bind-inter- faces and the default. Dnsmasq binds the address of individual interfaces, allowing multiple dnsmasq instances, but if new in- terfaces or addresses appear, it automatically listens on those (subject to any access-control configuration). This makes dynam- ically created interfaces work in the same way as the default. Implementing this option requires non-standard networking APIs and it is only available under Linux. On other platforms it falls-back to --bind-interfaces mode. -y, --localise-queries Return answers to DNS queries from /etc/hosts and --interface- name and --dynamic-host which depend on the interface over which the query was received. If a name has more than one address as- sociated with it, and at least one of those addresses is on the same subnet as the interface to which the query was sent, then return only the address(es) on that subnet and return all the available addresses otherwise. This allows for a server to have multiple addresses in /etc/hosts corresponding to each of its interfaces, and hosts will get the correct address based on which network they are attached to. Currently this facility is limited to IPv4. -b, --bogus-priv Bogus private reverse lookups. All reverse lookups for private IP ranges (ie 192.168.x.x, etc) which are not found in /etc/hosts or the DHCP leases file are answered with "no such domain" rather than being forwarded upstream. The set of pre- fixes affected is the list given in RFC6303, for IPv4 and IPv6. Enabling this also subtly alters DNSSEC validation for reverse lookups in the private ranges such that a non-secure DS record is accepted as proof that the range is not signed. This works around behaviour by the public DNS services which seem not to return validated proof-of-non-existence for DS records in these domains. -V, --alias=[<old-ip>]|[<start-ip>-<end-ip>],<new-ip>[,<mask>] Modify IPv4 addresses returned from upstream nameservers; old-ip is replaced by new-ip. If the optional mask is given then any address which matches the masked old-ip will be re-written. So, for instance --alias=1.2.3.0,6.7.8.0,255.255.255.0 will map 1.2.3.56 to 6.7.8.56 and 1.2.3.67 to 6.7.8.67. This is what Cisco PIX routers call "DNS doctoring". If the old IP is given as range, then only addresses in the range, rather than a whole subnet, are re-written. So --alias=192.168.0.10-192.168.0.40,10.0.0.0,255.255.255.0 maps 192.168.0.10->192.168.0.40 to 10.0.0.10->10.0.0.40 -B, --bogus-nxdomain=<ipaddr>[/prefix] Transform replies which contain the specified address or subnet into "No such domain" replies. IPv4 and IPv6 are supported. This is intended to counteract a devious move made by Verisign in September 2003 when they started returning the address of an ad- vertising web page in response to queries for unregistered names, instead of the correct NXDOMAIN response. This option tells dnsmasq to fake the correct response when it sees this be- haviour. As at Sept 2003 the IP address being returned by Verisign is 64.94.110.11 --ignore-address=<ipaddr>[/prefix] Ignore replies to A or AAAA queries which include the specified address or subnet. No error is generated, dnsmasq simply con- tinues to listen for another reply. This is useful to defeat blocking strategies which rely on quickly supplying a forged an- swer to a DNS request for certain domain, before the correct an- swer can arrive. -f, --filterwin2k Later versions of windows make periodic DNS requests which don't get sensible answers from the public DNS and can cause problems by triggering dial-on-demand links. This flag turns on an option to filter such requests. The requests blocked are for records of type ANY where the requested name has underscores, to catch LDAP requests, and for all records of types SOA and SRV. --filter-A Remove A records from answers. No IPv4 addresses will be re- turned. --filter-AAAA Remove AAAA records from answers. No IPv6 addresses will be re- turned. --filter-rr=<rrtype>[,<rrtype>...] Remove records of the specified type(s) from answers. The other- wise-nonsensical --filter-rr=ANY has a special meaning: it fil- ters replies to queries for type ANY. Everything other than A, AAAA, MX and CNAME records are removed. Since ANY queries with forged source addresses can be used in DNS amplification attacks (replies to ANY queries can be large) this defangs such attacks, whilst still supporting the one remaining possible use of ANY queries. See RFC 8482 para 4.3 for details. --cache-rr=<rrtype>[,<rrtype>...] By default, dnsmasq caches A, AAAA, CNAME and SRV DNS record types. This option adds other record types to the cache. The RR-type can be given as a name such as TXT or MX or a decimal number. A single --cache-rr option can take a comma-separated list of RR-types and more than one --cache-rr option is allowed. Use --cache-rr=ANY to enable caching for all RR-types. -r, --resolv-file=<file> Read the IP addresses of the upstream nameservers from <file>, instead of /etc/resolv.conf. For the format of this file see re- solv.conf(5). The only lines relevant to dnsmasq are nameserver ones. Dnsmasq can be told to poll more than one resolv.conf file, the first file name specified overrides the default, sub- sequent ones add to the list. This is only allowed when polling; the file with the currently latest modification time is the one used. -R, --no-resolv Don't read /etc/resolv.conf. Get upstream servers only from the command line or the dnsmasq configuration file. -1, --enable-dbus[=<service-name>] Allow dnsmasq configuration to be updated via DBus method calls. The configuration which can be changed is upstream DNS servers (and corresponding domains) and cache clear. Requires that dns- masq has been built with DBus support. If the service name is given, dnsmasq provides service at that name, rather than the default which is uk.org.thekelleys.dnsmasq --enable-ubus[=<service-name>] Enable dnsmasq UBus interface. It sends notifications via UBus on DHCPACK and DHCPRELEASE events. Furthermore it offers metrics and allows configuration of Linux connection track mark based filtering. When DNS query filtering based on Linux connection track marks is enabled UBus notifications are generated for each resolved or filtered DNS query. Requires that dnsmasq has been built with UBus support. If the service name is given, dnsmasq provides service at that namespace, rather than the default which is dnsmasq -o, --strict-order By default, dnsmasq will send queries to any of the upstream servers it knows about and tries to favour servers that are known to be up. Setting this flag forces dnsmasq to try each query with each server strictly in the order they appear in /etc/resolv.conf --all-servers By default, when dnsmasq has more than one upstream server available, it will send queries to just one server. Setting this flag forces dnsmasq to send all queries to all available servers. The reply from the server which answers first will be returned to the original requester. --dns-loop-detect Enable code to detect DNS forwarding loops; ie the situation where a query sent to one of the upstream server eventually re- turns as a new query to the dnsmasq instance. The process works by generating TXT queries of the form <hex>.test and sending them to each upstream server. The hex is a UID which encodes the instance of dnsmasq sending the query and the upstream server to which it was sent. If the query returns to the server which sent it, then the upstream server through which it was sent is dis- abled and this event is logged. Each time the set of upstream servers changes, the test is re-run on all of them, including ones which were previously disabled. --stop-dns-rebind Reject (and log) addresses from upstream nameservers which are in the private ranges. This blocks an attack where a browser be- hind a firewall is used to probe machines on the local network. For IPv6, the private range covers the IPv4-mapped addresses in private space plus all link-local (LL) and site-local (ULA) ad- dresses. --rebind-localhost-ok Exempt 127.0.0.0/8 and ::1 from rebinding checks. This address range is returned by realtime black hole servers, so blocking it may disable these services. --rebind-domain-ok=[<domain>]|[[/<domain>/[<domain>/] Do not detect and block dns-rebind on queries to these domains. The argument may be either a single domain, or multiple domains surrounded by '/', like the --server syntax, eg. --rebind-do- main-ok=/domain1/domain2/domain3/ -n, --no-poll Don't poll /etc/resolv.conf for changes. --clear-on-reload Whenever /etc/resolv.conf is re-read or the upstream servers are set via DBus, clear the DNS cache. This is useful when new nameservers may have different data than that held in cache. -D, --domain-needed Tells dnsmasq to never forward A or AAAA queries for plain names, without dots or domain parts, to upstream nameservers. If the name is not known from /etc/hosts or DHCP then a "not found" answer is returned. -S, --local, --server=[/[<domain>]/[domain/]][<server>[#<port>]][@<in- terface>][@<source-ip>[#<port>]] Specify upstream servers directly. Setting this flag does not suppress reading of /etc/resolv.conf, use --no-resolv to do that. If one or more optional domains are given, that server is used only for those domains and they are queried only using the specified server. This is intended for private nameservers: if you have a nameserver on your network which deals with names of the form xxx.internal.thekelleys.org.uk at 192.168.1.1 then giv- ing the flag --server=/internal.thekelleys.org.uk/192.168.1.1 will send all queries for internal machines to that nameserver, everything else will go to the servers in /etc/resolv.conf. An empty domain specification, // has the special meaning of "un- qualified names only" ie names without any dots in them. A non- standard port may be specified as part of the IP address using a # character. More than one --server flag is allowed, with re- peated domain or ipaddr parts as required. More specific domains take precedence over less specific do- mains, so: --server=/google.com/1.2.3.4 --server=/www.google.com/2.3.4.5 will send queries for google.com and gmail.google.com to 1.2.3.4, but www.google.com will go to 2.3.4.5 Matching of domains is normally done on complete labels, so /google.com/ matches google.com and www.google.com but NOT su- pergoogle.com. This can be overridden with a * at the start of a pattern only: /*google.com/ will match google.com and www.google.com AND supergoogle.com. The non-wildcard form has priority, so if /google.com/ and /*google.com/ are both speci- fied then google.com and www.google.com will match /google.com/ and /*google.com/ will only match supergoogle.com. For historical reasons, the pattern /.google.com/ is equivalent to /google.com/ if you wish to match any subdomain of google.com but NOT google.com itself, use /*.google.com/ The special server address '#' means, "use the standard servers", so --server=/google.com/1.2.3.4 --server=/www.google.com/# will send queries for google.com and its subdomains to 1.2.3.4, except www.google.com (and its subdo- mains) which will be forwarded as usual. Also permitted is a -S flag which gives a domain but no IP ad- dress; this tells dnsmasq that a domain is local and it may an- swer queries from /etc/hosts or DHCP but should never forward queries on that domain to any upstream servers. --local is a synonym for --server to make configuration files clearer in this case. IPv6 addresses may include an %interface scope-id, eg fe80::202:a412:4512:7bbf%eth0. The optional string after the @ character tells dnsmasq how to set the source of the queries to this nameserver. It can either be an ip-address, an interface name or both. The ip-address should belong to the machine on which dnsmasq is running, other- wise this server line will be logged and then ignored. If an in- terface name is given, then queries to the server will be forced via that interface; if an ip-address is given then the source address of the queries will be set to that address; and if both are given then a combination of ip-address and interface name will be used to steer requests to the server. The query-port flag is ignored for any servers which have a source address specified but the port may be specified directly as part of the source address. Forcing queries to an interface is not imple- mented on all platforms supported by dnsmasq. Upstream servers may be specified with a hostname rather than an IP address. In this case, dnsmasq will try to use the system resolver to get the IP address of a server during startup. If name resolution fails, starting dnsmasq fails, too. If the sys- tem's configuration is such that the system resolver sends DNS queries through the dnsmasq instance which is starting up then this will time-out and fail. --rev-server=<ip-address>[/<prefix-len>][,<server>][#<port>][@<inter- face>][@<source-ip>[#<port>]] This is functionally the same as --server, but provides some syntactic sugar to make specifying address-to-name queries eas- ier. For example --rev-server=1.2.3.0/24,192.168.0.1 is exactly equivalent to --server=/3.2.1.in-addr.arpa/192.168.0.1 Allowed prefix lengths are 1-32 (IPv4) and 1-128 (IPv6). If the prefix length is omitted, dnsmasq substitutes either 32 (IPv4) or 128 (IPv6). -A, --address=/<domain>[/<domain>...]/[<ipaddr>] Specify an IP address to return for any host in the given do- mains. A (or AAAA) queries in the domains are never forwarded and always replied to with the specified IP address which may be IPv4 or IPv6. To give multiple addresses or both IPv4 and IPv6 addresses for a domain, use repeated --address flags. Note that /etc/hosts and DHCP leases override this for individual names. A common use of this is to redirect the entire doubleclick.net do- main to some friendly local web server to avoid banner ads. The domain specification works in the same way as for --server, with the additional facility that /#/ matches any domain. Thus --ad- dress=/#/1.2.3.4 will always return 1.2.3.4 for any query not answered from /etc/hosts or DHCP and not sent to an upstream nameserver by a more specific --server directive. As for --server, one or more domains with no address returns a no-such- domain answer, so --address=/example.com/ is equivalent to --server=/example.com/ and returns NXDOMAIN for example.com and all its subdomains. An address specified as '#' translates to the NULL address of 0.0.0.0 and its IPv6 equivalent of :: so --address=/example.com/# will return NULL addresses for exam- ple.com and its subdomains. This is partly syntactic sugar for --address=/example.com/0.0.0.0 and --address=/example.com/:: but is also more efficient than including both as separate configu- ration lines. Note that NULL addresses normally work in the same way as localhost, so beware that clients looking up these names are likely to end up talking to themselves. Note that the behaviour for queries which don't match the speci- fied address literal changed in version 2.86. Previous ver- sions, configured with (eg) --address=/example.com/1.2.3.4 and then queried for a RR type other than A would return a NoData answer. From 2.86, the query is sent upstream. To restore the pre-2.86 behaviour, use the configuration --address=/exam- ple.com/1.2.3.4 --local=/example.com/ --ipset=/<domain>[/<domain>...]/<ipset>[,<ipset>...] Places the resolved IP addresses of queries for one or more do- mains in the specified Netfilter IP set. If multiple setnames are given, then the addresses are placed in each of them, sub- ject to the limitations of an IP set (IPv4 addresses cannot be stored in an IPv6 IP set and vice versa). Domains and subdo- mains are matched in the same way as --address. These IP sets must already exist. See ipset(8) for more details. --nftset=/<domain>[/<domain>...]/[(6|4)#[<family>#]<ta- ble>#<set>[,[(6|4)#[<family>#]<table>#<set>]...] Similar to the --ipset option, but accepts one or more nftables sets to add IP addresses into. These sets must already exist. See nft(8) for more details. The family, table and set are passed directly to the nft. If the spec starts with 4# or 6# then only A or AAAA records respectively are added to the set. Since an nftset can hold only IPv4 or IPv6 addresses, this avoids errors being logged for addresses of the wrong type. --connmark-allowlist-enable[=<mask>] Enables filtering of incoming DNS queries with associated Linux connection track marks according to individual allowlists con- figured via a series of --connmark-allowlist options. Disallowed queries are not forwarded; they are rejected with a REFUSED er- ror code. DNS queries are only allowed if they do not have an associated Linux connection track mark, or if the queried do- mains match the configured DNS patterns for the associated Linux connection track mark. If no allowlist is configured for a Linux connection track mark, all DNS queries associated with that mark are rejected. If a mask is specified, Linux connection track marks are first bitwise ANDed with the given mask before being processed. --connmark-allowlist=<connmark>[/<mask>][,<pattern>[/<pattern>...]] Configures the DNS patterns that are allowed in DNS queries as- sociated with the given Linux connection track mark. If a mask is specified, Linux connection track marks are first bitwise ANDed with the given mask before they are compared to the given connection track mark. Patterns follow the syntax of DNS names, but additionally allow the wildcard character "*" to be used up to twice per label to match 0 or more characters within that la- bel. Note that the wildcard never matches a dot (e.g., "*.exam- ple.com" matches "api.example.com" but not "api.us.exam- ple.com"). Patterns must be fully qualified, i.e., consist of at least two labels. The final label must not be fully numeric, and must not be the "local" pseudo-TLD. A pattern must end with at least two literal (non-wildcard) labels. Instead of a pattern, "*" can be specified to disable allowlist filtering for a given Linux connection track mark entirely. -m, --mx-host=<mx name>[[,<hostname>],<preference>] Return an MX record named <mx name> pointing to the given host- name (if given), or the host specified in the --mx-target switch or, if that switch is not given, the host on which dnsmasq is running. The default is useful for directing mail from systems on a LAN to a central server. The preference value is optional, and defaults to 1 if not given. More than one MX record may be given for a host. -t, --mx-target=<hostname> Specify the default target for the MX record returned by dns- masq. See --mx-host. If --mx-target is given, but not --mx- host, then dnsmasq returns a MX record containing the MX target for MX queries on the hostname of the machine on which dnsmasq is running. -e, --selfmx Return an MX record pointing to itself for each local machine. Local machines are those in /etc/hosts or with DHCP leases. -L, --localmx Return an MX record pointing to the host given by --mx-target (or the machine on which dnsmasq is running) for each local ma- chine. Local machines are those in /etc/hosts or with DHCP leases. -W, --srv-host=<_service>.<_prot>[.<domain>],[<target>[,<port>[,<prior- ity>[,<weight>]]]] Return a SRV DNS record. See RFC2782 for details. If not sup- plied, the domain defaults to that given by --domain. The de- fault for the target domain is empty, and the default for port is one and the defaults for weight and priority are zero. Be careful if transposing data from BIND zone files: the port, weight and priority numbers are in a different order. More than one SRV record for a given service/domain is allowed, all that match are returned. --host-record=<name>[,<name>....],[<IPv4-address>],[<IPv6-ad- dress>][,<TTL>] Add A, AAAA and PTR records to the DNS. This adds one or more names to the DNS with associated IPv4 (A) and IPv6 (AAAA) records. A name may appear in more than one --host-record and therefore be assigned more than one address. Only the first ad- dress creates a PTR record linking the address to the name. This is the same rule as is used reading hosts-files. --host-record options are considered to be read before host-files, so a name appearing there inhibits PTR-record creation if it appears in hosts-file also. Unlike hosts-files, names are not expanded, even when --expand-hosts is in effect. Short and long names may appear in the same --host-record, eg. --host-record=laptop,lap- top.thekelleys.org,192.168.0.1,1234::100 If the time-to-live is given, it overrides the default, which is zero or the value of --local-ttl. The value is a positive inte- ger and gives the time-to-live in seconds. --dynamic-host=<name>,[IPv4-address],[IPv6-address],<interface> Add A, AAAA and PTR records to the DNS in the same subnet as the specified interface. The address is derived from the network part of each address associated with the interface, and the host part from the specified address. For example --dynamic-host=ex- ample.com,0.0.0.8,eth0 will, when eth0 has the address 192.168.78.x and netmask 255.255.255.0 give the name example.com an A record for 192.168.78.8. The same principle applies to IPv6 addresses. Note that if an interface has more than one address, more than one A or AAAA record will be created. The TTL of the records is always zero, and any changes to interface addresses will be immediately reflected in them. -Y, --txt-record=<name>[[,<text>],<text>] Return a TXT DNS record. The value of TXT record is a set of strings, so any number may be included, delimited by commas; use quotes to put commas into a string. Note that the maximum length of a single string is 255 characters, longer strings are split into 255 character chunks. --ptr-record=<name>[,<target>] Return a PTR DNS record. --naptr-record=<name>,<order>,<preference>,<flags>,<service>,<reg- exp>[,<replacement>] Return an NAPTR DNS record, as specified in RFC3403. --caa-record=<name>,<flags>,<tag>,<value> Return a CAA DNS record, as specified in RFC6844. --cname=<cname>,[<cname>,]<target>[,<TTL>] Return a CNAME record which indicates that <cname> is really <target>. There is a significant limitation on the target; it must be a DNS record which is known to dnsmasq and NOT a DNS record which comes from an upstream server. The cname must be unique, but it is permissible to have more than one cname point- ing to the same target. Indeed it's possible to declare multiple cnames to a target in a single line, like so: --cname=cname1,cname2,target If the time-to-live is given, it overrides the default, which is zero or the value of --local-ttl. The value is a positive inte- ger and gives the time-to-live in seconds. --dns-rr=<name>,<RR-number>,[<hex data>] Return an arbitrary DNS Resource Record. The number is the type of the record (which is always in the C_IN class). The value of the record is given by the hex data, which may be of the form 01:23:45 or 01 23 45 or 012345 or any mixture of these. --interface-name=<name>,<interface>[/4|/6] Return DNS records associating the name with the address(es) of the given interface. This flag specifies an A or AAAA record for the given name in the same way as an /etc/hosts line, except that the address is not constant, but taken from the given in- terface. The interface may be followed by "/4" or "/6" to spec- ify that only IPv4 or IPv6 addresses of the interface should be used. If the interface is down, not configured or non-existent, an empty record is returned. The matching PTR record is also created, mapping the interface address to the name. More than one name may be associated with an interface address by repeat- ing the flag; in that case the first instance is used for the reverse address-to-name mapping. Note that a name used in --in- terface-name may not appear in /etc/hosts. --synth-domain=<domain>,<address range>[,<prefix>[*]] Create artificial A/AAAA and PTR records for an address range. The records either seqential numbers or the address, with peri- ods (or colons for IPv6) replaced with dashes. An examples should make this clearer. First sequential numbers. --synth-domain=thekelleys.org.uk,192.168.0.50,192.168.0.70,in- ternal-* results in the name internal-0.thekelleys.org.uk. re- turning 192.168.0.50, internal-1.thekelleys.org.uk returning 192.168.0.51 and so on. (note the *) The same principle applies to IPv6 addresses (where the numbers may be very large). Reverse lookups from address to name behave as expected. Second, --synth-domain=thekelleys.org.uk,192.168.0.0/24,inter- nal- (no *) will result in a query for inter- nal-192-168-0-56.thekelleys.org.uk returning 192.168.0.56 and a reverse query vice versa. The same applies to IPv6; the repre- sentation doesn't use the :: compression feature or the special representation of V4 mapped IPv6 addresses as these can generate illegal domain names, so all domains are of the form inter- nal-1000-0000-0000-0000-0000-0000-0000-0008.example.com The address range can be of the form <start address>,<end ad- dress> or <ip address>/<prefix-length> in both forms of the op- tion. For IPv6 the start and end addresses must fall in the same /64 network, or prefix-length must be greater than or equal to 64 except that shorter prefix lengths than 64 are allowed only if non-sequential names are in use. --dumpfile=<path/to/file> Specify the location of a pcap-format file which dnsmasq uses to dump copies of network packets for debugging purposes. If the file exists when dnsmasq starts, it is not deleted; new packets are added to the end. The file may be a named-pipe which Wire- shark is listening to. --dumpmask=<mask> Specify which types of packets should be added to the dumpfile. The argument should be the OR of the bitmasks for each type of packet to be dumped: it can be specified in hex by preceding the number with 0x in the normal way. Each time a packet is written to the dumpfile, dnsmasq logs the packet sequence and the mask representing its type. The current types are: 0x0001 - DNS queries from clients, 0x0002 DNS replies to clients, 0x0004 - DNS queries to upstream, 0x0008 - DNS replies from upstream, 0x0010 - queries send upstream for DNSSEC validation, 0x0020 - replies to queries for DNSSEC validation, 0x0040 - replies to client queries which fail DNSSEC validation, 0x0080 replies to queries for DNSSEC validation which fail validation, 0x1000 - DHCPv4, 0x2000 - DHCPv6, 0x4000 - Router advertisement, 0x8000 - TFTP. --add-mac[=base64|text] Add the MAC address of the requestor to DNS queries which are forwarded upstream. This may be used to DNS filtering by the up- stream server. The MAC address can only be added if the re- questor is on the same subnet as the dnsmasq server. Note that the mechanism used to achieve this (an EDNS0 option) is not yet standardised, so this should be considered experimental. Also note that exposing MAC addresses in this way may have security and privacy implications. The warning about caching given for --add-subnet applies to --add-mac too. An alternative encoding of the MAC, as base64, is enabled by adding the "base64" parame- ter and a human-readable encoding of hex-and-colons is enabled by added the "text" parameter. --strip-mac Remove any MAC address information already in downstream queries before forwarding upstream. --add-cpe-id=<string> Add an arbitrary identifying string to DNS queries which are forwarded upstream. --add-subnet[[=[<IPv4 address>/]<IPv4 prefix length>][,[<IPv6 ad- dress>/]<IPv6 prefix length>]] Add a subnet address to the DNS queries which are forwarded up- stream. If an address is specified in the flag, it will be used, otherwise, the address of the requestor will be used. The amount of the address forwarded depends on the prefix length parameter: 32 (128 for IPv6) forwards the whole address, zero forwards none of it but still marks the request so that no upstream nameserver will add client address information either. The default is zero for both IPv4 and IPv6. Note that upstream nameservers may be configured to return different results based on this informa- tion, but the dnsmasq cache does not take account. Caching is therefore disabled for such replies, unless the subnet address being added is constant. For example, --add-subnet=24,96 will add the /24 and /96 subnets of the requestor for IPv4 and IPv6 requestors, respectively. --add-subnet=1.2.3.4/24 will add 1.2.3.0/24 for IPv4 requestors and ::/0 for IPv6 requestors. --add-sub- net=1.2.3.4/24,1.2.3.4/24 will add 1.2.3.0/24 for both IPv4 and IPv6 requestors. --strip-subnet Remove any subnet address already present in a downstream query before forwarding it upstream. If --add-subnet is set this also ensures that any downstream-provided subnet is replaced by the one added by dnsmasq. Otherwise, dnsmasq will NOT replace an ex- isting subnet in the query. --umbrella[=[deviceid:<deviceid>][,orgid:<orgid>][,assetid:<id>]] Embeds the requestor's IP address in DNS queries forwarded up- stream. If device id or, asset id or organization id are speci- fied, the information is included in the forwarded queries and may be able to be used in filtering policies and reporting. The order of the id attributes is irrelevant, but they must be sepa- rated by a comma. Deviceid is a sixteen digit hexadecimal num- ber, org and asset ids are decimal numbers. -c, --cache-size=<cachesize> Set the size of dnsmasq's cache. The default is 150 names. Set- ting the cache size to zero disables caching. Note: huge cache size impacts performance. -N, --no-negcache Disable negative caching. Negative caching allows dnsmasq to re- member "no such domain" answers from upstream nameservers and answer identical queries without forwarding them again. --no-round-robin Dnsmasq normally permutes the order of A or AAAA records for the same name on successive queries, for load-balancing. This turns off that behaviour, so that the records are always returned in the order that they are received from upstream. --do-0x20-encode, --no-0x20-encode Dnsmasq can scramble the case of letters in DNS queries it sends upstream as a security feature. This technique can interact badly with rare broken DNS servers which don't preserve the case of the query in their reply. The first time a reply is returned which matches the query in all respects except case, a warning will be logged. If this coincides with DNS not functioning, it is necessary to disable the feature. As at version 2.91, 0x20 encoding is disabled by default, and must be enabled with --do-0x20-encode. The default may change in the future, so to be sure of its status after an upgrade, set --do-0x20-encode or --no-0x20-encode in your config. --no-0x20-encode overrides --do-x20-encode or a future default 0x20-encode enable. --use-stale-cache[=<max TTL excess in s>] When set, if a DNS name exists in the cache, but its time-to- live has expired, dnsmasq will return the data anyway. (It at- tempts to refresh the data with an upstream query after return- ing the stale data.) This can improve speed and reliability. It comes at the expense of sometimes returning out-of-date data and less efficient cache utilisation, since old data cannot be flushed when its TTL expires, so the cache becomes mostly least- recently-used. To mitigate issues caused by massively outdated DNS replies, the maximum overaging of cached records can be specified in seconds (defaulting to not serve anything older than one day). Setting the TTL excess time to zero will serve stale cache data regardless how long it has expired. -0, --dns-forward-max=<queries> Set the maximum number of concurrent DNS queries. The default value is 150, which should be fine for most setups. The only known situation where this needs to be increased is when using web-server log file resolvers, which can generate large numbers of concurrent queries. This parameter actually controls the num- ber of concurrent queries per server group, where a server group is the set of server(s) associated with a single domain. So if a domain has its own server via --server=/example.com/1.2.3.4 and 1.2.3.4 is not responding, but queries for *.example.com cannot go elsewhere, then other queries will not be affected. On con- figurations with many such server groups and tight resources, this value may need to be reduced. --dnssec Validate DNS replies and cache DNSSEC data. When forwarding DNS queries, dnsmasq requests the DNSSEC records needed to validate the replies. The replies are validated and the result returned as the Authenticated Data bit in the DNS packet. In addition the DNSSEC records are stored in the cache, making validation by clients more efficient. Note that validation by clients is the most secure DNSSEC mode, but for clients unable to do valida- tion, use of the AD bit set by dnsmasq is useful, provided that the network between the dnsmasq server and the client is trusted. Dnsmasq must be compiled with HAVE_DNSSEC enabled, and DNSSEC trust anchors provided, see --trust-anchor. Because the DNSSEC validation process uses the cache, it is not permitted to reduce the cache size below the default when DNSSEC is enabled. The nameservers upstream of dnsmasq must be DNSSEC-capable, ie capable of returning DNSSEC records with data. If they are not, then dnsmasq will not be able to determine the trusted status of answers and this means that DNS service will be entirely broken. --trust-anchor=<domain>,[<class>,][<key-tag>,<algorithm>,<digest- type>,<digest>] Provide DS records to act a trust anchors for DNSSEC validation. The class defaults to IN. Typically these will be the DS record(s) for Key Signing key(s) (KSK) of the root zone, but trust anchors for limited domains are also possible. A negative trust anchor (ie. proof that a DS record doesn't exist) may be configured be specifying only the name or only the name and class. This can be useful for forcing dnsmasq to treat zones delegated using --server=/<domain>/<ip-address> as unsigned. The current root-zone trust anchors may be downloaded from https://data.iana.org/root-anchors/root-anchors.xml --dnssec-check-unsigned[=no] As a default, dnsmasq checks that unsigned DNS replies are le- gitimate: this entails possible extra queries even for the ma- jority of DNS zones which are not, at the moment, signed. If --dnssec-check-unsigned=no appears in the configuration, then such replies they are assumed to be valid and passed on (without the "authentic data" bit set, of course). This does not protect against an attacker forging unsigned replies for signed DNS zones, but it is fast. Versions of dnsmasq prior to 2.80 defaulted to not checking un- signed replies, and used --dnssec-check-unsigned to switch this on. Such configurations will continue to work as before, but those which used the default of no checking will need to be al- tered to explicitly select no checking. The new default is be- cause switching off checking for unsigned replies is inherently dangerous. Not only does it open the possibility of forged replies, but it allows everything to appear to be working even when the upstream namesevers do not support DNSSEC, and in this case no DNSSEC validation at all is occurring. --dnssec-no-timecheck DNSSEC signatures are only valid for specified time windows, and should be rejected outside those windows. This generates an in- teresting chicken-and-egg problem for machines which don't have a hardware real time clock. For these machines to determine the correct time typically requires use of NTP and therefore DNS, but validating DNS requires that the correct time is already known. Setting this flag removes the time-window checks (but not other DNSSEC validation.) only until the dnsmasq process re- ceives SIGINT. The intention is that dnsmasq should be started with this flag when the platform determines that reliable time is not currently available. As soon as reliable time is estab- lished, a SIGINT should be sent to dnsmasq, which enables time checking, and purges the cache of DNS records which have not been thoroughly checked. Earlier versions of dnsmasq overloaded SIGHUP (which re-reads much configuration) to also enable time validation. If dnsmasq is run in debug mode (--no-daemon flag) then SIGINT retains its usual meaning of terminating the dnsmasq process. --dnssec-timestamp=<path> Enables an alternative way of checking the validity of the sys- tem time for DNSSEC (see --dnssec-no-timecheck). In this case, the system time is considered to be valid once it becomes later than the timestamp on the specified file. The file is created and its timestamp set automatically by dnsmasq. The file must be stored on a persistent filesystem, so that it and its mtime are carried over system restarts. The timestamp file is created af- ter dnsmasq has dropped root, so it must be in a location writable by the unprivileged user that dnsmasq runs as. --proxy-dnssec Copy the DNSSEC Authenticated Data bit from upstream servers to downstream clients. This is an alternative to having dnsmasq validate DNSSEC, but it depends on the security of the network between dnsmasq and the upstream servers, and the trustworthi- ness of the upstream servers. Note that caching the Authenti- cated Data bit correctly in all cases is not technically possi- ble. If the AD bit is to be relied upon when using this option, then the cache should be disabled using --cache-size=0. In most cases, enabling DNSSEC validation within dnsmasq is a better op- tion. See --dnssec for details. --dnssec-limits=<limit>[,<limit>.......] Override the default resource limits applied to DNSSEC valida- tion. Cryptographic operations are expensive and crafted domains can DoS a DNSSEC validator by forcing it to do hundreds of thou- sands of such operations. To avoid this, the dnsmasq validation code applies limits on how much work will be expended in valida- tion. If any of the limits are exceeded, the validation will fail and the domain treated as BOGUS. There are four limits, in order(default values in parens): number a signature validation fails per RRset(20), number of signature validations and hash computations per query(200), number of sub-queries to fetch DS and DNSKEY RRsets per query(40), and the number of iterations in a NSEC3 record(150). The maximum values reached during valida- tion are stored, and dumped as part of the stats generated by SIGUSR1. Supplying a limit value of 0 leaves the default in place, so --dnssec-limits=0,0,20 sets the number of sub-queries to 20 whilst leaving the other limits at default values. --dnssec-debug Set debugging mode for the DNSSEC validation, set the Checking Disabled bit on upstream queries, and don't convert replies which do not validate to responses with a return code of SERV- FAIL. Note that setting this may affect DNS behaviour in bad ways, it is not an extra-logging flag and should not be set in production. --auth-zone=<domain>[,<subnet>[/<prefix length>][,<subnet>[/<prefix length>].....][,exclude:<subnet>[/<prefix length>]].....] Define a DNS zone for which dnsmasq acts as authoritative server. Locally defined DNS records which are in the domain will be served. If subnet(s) are given, A and AAAA records must be in one of the specified subnets. As alternative to directly specifying the subnets, it's possible to give the name of an interface, in which case the subnets im- plied by that interface's configured addresses and netmask/pre- fix-length are used; this is useful when using constructed DHCP ranges as the actual address is dynamic and not known when con- figuring dnsmasq. The interface addresses may be confined to only IPv6 addresses using <interface>/6 or to only IPv4 using <interface>/4. This is useful when an interface has dynamically determined global IPv6 addresses which should appear in the zone, but RFC1918 IPv4 addresses which should not. Interface- name and address-literal subnet specifications may be used freely in the same --auth-zone declaration. It's possible to exclude certain IP addresses from responses. It can be used, to make sure that answers contain only global routeable IP addresses (by excluding loopback, RFC1918 and ULA addresses). The subnet(s) are also used to define in-addr.arpa and ip6.arpa domains which are served for reverse-DNS queries. If not speci- fied, the prefix length defaults to 24 for IPv4 and 64 for IPv6. For IPv4 subnets, the prefix length should be have the value 8, 16 or 24 unless you are familiar with RFC 2317 and have arranged the in-addr.arpa delegation accordingly. Note that if no subnets are specified, then no reverse queries are answered. --auth-soa=<serial>[,<hostmaster>[,<refresh>[,<retry>[,<expiry>]]]] Specify fields in the SOA record associated with authoritative zones. Note that this is optional, all the values are set to sane defaults. --auth-sec-servers=<domain>[,<domain>[,<domain>...]] Specify any secondary servers for a zone for which dnsmasq is authoritative. These servers must be configured to get zone data from dnsmasq by zone transfer, and answer queries for the same authoritative zones as dnsmasq. --auth-peer=<ip-address>[,<ip-address>[,<ip-address>...]] Specify the addresses of secondary servers which are allowed to initiate zone transfer (AXFR) requests for zones for which dns- masq is authoritative. If this option is not given but --auth- sec-servers is, then AXFR requests will be accepted from any secondary. Specifying --auth-peer without --auth-sec-servers en- ables zone transfer but does not advertise the secondary in NS records returned by dnsmasq. --conntrack Read the Linux connection track mark associated with incoming DNS queries and set the same mark value on upstream traffic used to answer those queries. This allows traffic generated by dns- masq to be associated with the queries which cause it, useful for bandwidth accounting and firewalling. Dnsmasq must have con- ntrack support compiled in and the kernel must have conntrack support included and configured. This option cannot be combined with --query-port. -F, --dhcp-range=[tag:<tag>[,tag:<tag>],][set:<tag>,]<start- addr>[,<end-addr>|<mode>[,<netmask>[,<broadcast>]]][,<lease time>] -F, --dhcp-range=[tag:<tag>[,tag:<tag>],][set:<tag>,]<start- IPv6addr>[,<end-IPv6addr>|constructor:<interface>][,<mode>][,<prefix- len>][,<lease time>] Enable the DHCP server. Addresses will be given out from the range <start-addr> to <end-addr> and from statically defined ad- dresses given in --dhcp-host options. If the lease time is given, then leases will be given for that length of time. The lease time is in seconds, or minutes (eg 45m) or hours (eg 1h) or days (2d) or weeks (1w) or "infinite". If not given, the de- fault lease time is one hour for IPv4 and one day for IPv6. The minimum lease time is two minutes. For IPv6 ranges, the lease time maybe "deprecated"; this sets the preferred lifetime sent in a DHCP lease or router advertisement to zero, which causes clients to use other addresses, if available, for new connec- tions as a prelude to renumbering. This option may be repeated, with different addresses, to enable DHCP service to more than one network. For directly connected networks (ie, networks on which the machine running dnsmasq has an interface) the netmask is optional: dnsmasq will determine it from the interface configuration. For networks which receive DHCP service via a relay agent, dnsmasq cannot determine the netmask itself, so it should be specified, otherwise dnsmasq will have to guess, based on the class (A, B or C) of the net- work address. The broadcast address is always optional. It is always allowed to have more than one --dhcp-range in a single subnet. For IPv6, the parameters are slightly different: instead of net- mask and broadcast address, there is an optional prefix length which must be equal to or larger then the prefix length on the local interface. If not given, this defaults to 64. Unlike the IPv4 case, the prefix length is not automatically derived from the interface configuration. The minimum size of the prefix length is 64. IPv6 (only) supports another type of range. In this, the start address and optional end address contain only the network part (ie ::1) and they are followed by constructor:<interface>. This forms a template which describes how to create ranges, based on the addresses assigned to the interface. For instance --dhcp-range=::1,::400,constructor:eth0 will look for addresses on eth0 and then create a range from <network>::1 to <network>::400. If the interface is assigned more than one network, then the corresponding ranges will be au- tomatically created, and then deprecated and finally removed again as the address is deprecated and then deleted. The inter- face name may have a final "*" wildcard. Note that just any ad- dress on eth0 will not do: it must not be an autoconfigured or privacy address, or be deprecated. If a --dhcp-range is only being used for stateless DHCP and/or SLAAC, then the address can be simply :: --dhcp-range=::,constructor:eth0 The optional set:<tag> sets an alphanumeric label which marks this network so that DHCP options may be specified on a per-net- work basis. When it is prefixed with 'tag:' instead, then its meaning changes from setting a tag to matching it. Only one tag may be set, but more than one tag may be matched. The optional <mode> keyword may be static which tells dnsmasq to enable DHCP for the network specified, but not to dynamically allocate IP addresses: only hosts which have static addresses given via --dhcp-host or from /etc/ethers will be served. A sta- tic-only subnet with address all zeros may be used as a "catch- all" address to enable replies to all Information-request pack- ets on a subnet which is provided with stateless DHCPv6, ie --dhcp-range=::,static For IPv4, the <mode> may be proxy in which case dnsmasq will provide proxy-DHCP on the specified subnet. (See --pxe-prompt and --pxe-service for details.) For IPv6, the mode may be some combination of ra-only, slaac, ra-names, ra-stateless, ra-advrouter, off-link. ra-only tells dnsmasq to offer Router Advertisement only on this subnet, and not DHCP. slaac tells dnsmasq to offer Router Advertisement on this subnet and to set the A bit in the router advertisement, so that the client will use SLAAC addresses. When used with a DHCP range or static DHCP address this results in the client having both a DHCP-assigned and a SLAAC address. ra-stateless sends router advertisements with the O and A bits set, and provides a stateless DHCP service. The client will use a SLAAC address, and use DHCP for other configuration informa- tion. ra-names enables a mode which gives DNS names to dual-stack hosts which do SLAAC for IPv6. Dnsmasq uses the host's IPv4 lease to derive the name, network segment and MAC address and assumes that the host will also have an IPv6 address calculated using the SLAAC algorithm, on the same network segment. The ad- dress is pinged, and if a reply is received, an AAAA record is added to the DNS for this IPv6 address. Note that this is only happens for directly-connected networks, (not one doing DHCP via a relay) and it will not work if a host is using privacy exten- sions. ra-names can be combined with ra-stateless and slaac. ra-advrouter enables a mode where router address(es) rather than prefix(es) are included in the advertisements. This is de- scribed in RFC-3775 section 7.2 and is used in mobile IPv6. In this mode the interval option is also included, as described in RFC-3775 section 7.3. off-link tells dnsmasq to advertise the prefix without the on- link (aka L) bit set. -G, --dhcp- host=[<hwaddr>][,id:<client_id>|*][,set:<tag>][,tag:<tag>][,<ipaddr>][,<host- name>][,<lease_time>][,ignore] Specify per host parameters for the DHCP server. This allows a machine with a particular hardware address to be always allo- cated the same hostname, IP address and lease time. A hostname specified like this overrides any supplied by the DHCP client on the machine. It is also allowable to omit the hardware address and include the hostname, in which case the IP address and lease times will apply to any machine claiming that name. For example --dhcp-host=00:20:e0:3b:13:af,wap,infinite tells dnsmasq to give the machine with hardware address 00:20:e0:3b:13:af the name wap, and an infinite DHCP lease. --dhcp-host=lap,192.168.0.199 tells dnsmasq to always allocate the machine lap the IP address 192.168.0.199. Addresses allocated like this are not constrained to be in the range given by the --dhcp-range option, but they must be in the same subnet as some valid dhcp-range. For subnets which don't need a pool of dynamically allocated addresses, use the "static" keyword in the --dhcp-range declaration. It is allowed to use client identifiers (called client DUID in IPv6-land) rather than hardware addresses to identify hosts by prefixing with 'id:'. Thus: --dhcp-host=id:01:02:03:04,..... refers to the host with client identifier 01:02:03:04. It is also allowed to specify the client ID as text, like this: --dhcp-host=id:clientidastext,..... A single --dhcp-host may contain an IPv4 address or one or more IPv6 addresses, or both. IPv6 addresses must be bracketed by square brackets thus: --dhcp-host=laptop,[1234::56] IPv6 ad- dresses may contain only the host-identifier part: --dhcp- host=laptop,[::56] in which case they act as wildcards in con- structed DHCP ranges, with the appropriate network part in- serted. For IPv6, an address may include a prefix length: --dhcp-host=laptop,[1234:50/126] which (in this case) specifies four addresses, 1234::50 to 1234::53. This (an the ability to specify multiple addresses) is useful when a host presents ei- ther a consistent name or hardware-ID, but varying DUIDs, since it allows dnsmasq to honour the static address allocation but assign a different address for each DUID. This typically occurs when chain netbooting, as each stage of the chain gets in turn allocates an address. Note that in IPv6 DHCP, the hardware address may not be avail- able, though it normally is for direct-connected clients, or clients using DHCP relays which support RFC 6939. For DHCPv4, the special option id:* means "ignore any client-id and use MAC addresses only." This is useful when a client presents a client-id sometimes but not others. If a name appears in /etc/hosts, the associated address can be allocated to a DHCP lease, but only if a --dhcp-host option specifying the name also exists. Only one hostname can be given in a --dhcp-host option, but aliases are possible by using CNAMEs. (See --cname ). Note that /etc/hosts is NOT used when the DNS server side of dnsmasq is disabled by setting the DNS server port to zero. More than one --dhcp-host can be associated (by name, hardware address or UID) with a host. Which one is used (and therefore which address is allocated by DHCP and appears in the DNS) de- pends on the subnet on which the host last obtained a DHCP lease: the --dhcp-host with an address within the subnet is used. If more than one address is within the subnet, the result is undefined. A corollary to this is that the name associated with a host using --dhcp-host does not appear in the DNS until the host obtains a DHCP lease. The special keyword ignore tells dnsmasq never to offer a DHCP lease to a machine. The machine can be specified by hardware ad- dress, client ID or hostname. For example: --dhcp- host=00:20:e0:3b:13:af,ignore. This can be useful when there is another DHCP server on the network which should be used by some machines. The set:<tag> construct sets the tag whenever this --dhcp-host directive is in use. This can be used to selectively send DHCP options just for this host. More than one tag can be set in a --dhcp-host directive (but not in other places where set:<tag> is allowed). When a host matches any --dhcp-host directive (or one implied by /etc/ethers) then the special tag known is set. This allows dnsmasq to be configured to ignore requests from un- known machines using --dhcp-ignore=tag:!known. If the host matches only a --dhcp-host directive which cannot be used be- cause it specifies an address on a different subnet, the tag known-othernet is set. The tag:<tag> construct filters which dhcp-host directives are used. More than one tag can be provided. In this case, the re- quest must match all tags. Tagged directives are used in prefer- ence to untagged ones. Note that one of <hwaddr>, <client_id> or <hostname> still must be specified (can be a wildcard). Ethernet addresses (but not client-ids) may have wildcard bytes, so for example --dhcp-host=00:20:e0:3b:13:*,ignore will cause dnsmasq to ignore the given range of hardware addresses. Note that the "*" will need to be escaped or quoted on a command line, but not in the configuration file. Hardware addresses normally match any network (ARP) type, but it is possible to restrict them to a single ARP type by preceding them with the ARP-type (in HEX) and "-". so --dhcp- host=06-00:20:e0:3b:13:af,1.2.3.4 will only match a Token-Ring hardware address, since the ARP-address type for token ring is 6. As a special case, in DHCPv4, it is possible to include more than one hardware address. eg: --dhcp- host=11:22:33:44:55:66,12:34:56:78:90:12,192.168.0.2. This al- lows an IP address to be associated with multiple hardware ad- dresses, and gives dnsmasq permission to abandon a DHCP lease to one of the hardware addresses when another one asks for a lease. Beware that this is a dangerous thing to do: it will only work reliably if only one of the hardware addresses is active at any time and there is no way for dnsmasq to enforce this. It is, for instance, useful to allocate a stable IP address to a laptop which has both wired and wireless interfaces. --dhcp-hostsfile=<path> Read DHCP host information from the specified file. If a direc- tory is given, then read all the files contained in that direc- tory in alphabetical order. The file contains information about one host per line. The format of a line is the same as text to the right of '=' in --dhcp-host. The advantage of storing DHCP host information in this file is that it can be changed without re-starting dnsmasq: the file will be re-read when dnsmasq re- ceives SIGHUP. --dhcp-optsfile=<path> Read DHCP option information from the specified file. If a di- rectory is given, then read all the files contained in that di- rectory in alphabetical order. The advantage of using this op- tion is the same as for --dhcp-hostsfile: the --dhcp-optsfile will be re-read when dnsmasq receives SIGHUP. Note that it is possible to encode the information in a --dhcp-boot flag as DHCP options, using the options names bootfile-name, server-ip-ad- dress and tftp-server. This allows these to be included in a --dhcp-optsfile. --dhcp-hostsdir=<path> This is equivalent to --dhcp-hostsfile, except for the follow- ing. The path MUST be a directory, and not an individual file. Changed or new files within the directory are read automati- cally, without the need to send SIGHUP. If a file is deleted or changed after it has been read by dnsmasq, then the host record it contained will remain until dnsmasq receives a SIGHUP, or is restarted; ie host records are only added dynamically. The order in which the files in a directory are read is not defined. --dhcp-optsdir=<path> This is equivalent to --dhcp-optsfile, with the differences noted for --dhcp-hostsdir. -Z, --read-ethers Read /etc/ethers for information about hosts for the DHCP server. The format of /etc/ethers is a hardware address, fol- lowed by either a hostname or dotted-quad IP address. When read by dnsmasq these lines have exactly the same effect as --dhcp- host options containing the same information. /etc/ethers is re- read when dnsmasq receives SIGHUP. IPv6 addresses are NOT read from /etc/ethers. -O, --dhcp-option=[tag:<tag>,[tag:<tag>,]][encap:<opt>,][vi-encap:<en- terprise>,][vendor:[<vendor-class>],][<opt>|option:<opt-name>|op- tion6:<opt>|option6:<opt-name>],[<value>[,<value>]] Send various extra options to DHCP clients. By default, dnsmasq sends some standard options to DHCP clients, the netmask and broadcast address are set to the same as the host running dns- masq, and the DNS server and default route are set to the ad- dress of the machine running dnsmasq. (Equivalent rules apply for IPv6.) If the domain name option has been set, that is sent. This configuration allows these defaults to be overridden, or other options specified. The option to be sent may be given as a decimal number or as option:<option-name>. Option numbers are specified in RFC2132 and subsequent RFCs. The set of option-names known by dnsmasq can be discovered by run- ning dnsmasq --help dhcp. For example, to set the default route option to 192.168.4.4, use --dhcp-option=3,192.168.4.4 or --dhcp-option=option:router,192.168.4.4 and to set the time- server address to 192.168.0.4, use --dhcp-option=42,192.168.0.4 or --dhcp-option=option:ntp-server,192.168.0.4. The special ad- dress 0.0.0.0 means "the address of the system running dnsmasq". An option without data is valid, and includes just the option without data. (There is only one option with a zero length data field currently defined for DHCPv4, 80:rapid commit, so this feature is not very useful in practice). Options for which dns- masq normally provides default values can be omitted by defining the option with no data. These are netmask, broadcast, router, DNS server, domainname and hostname. Thus, for DHCPv4 --dhcp-op- tion = option:router will result in no router option being sent, rather than the default of the host on which dnsmasq is running. For DHCPv6, the same is true of the options DNS server and re- fresh time. Data types allowed are comma separated dotted-quad IPv4 ad- dresses, []-wrapped IPv6 addresses, a decimal number, colon-sep- arated hex digits and a text string. If the optional tags are given then this option is only sent when all the tags are matched. Special processing is done on a text argument for option 119, to conform with RFC 3397. Text or dotted-quad IP addresses as argu- ments to option 120 are handled as per RFC 3361. Dotted-quad IP addresses which are followed by a slash and then a netmask size are encoded as described in RFC 3442. IPv6 options are specified using the option6: keyword, followed by the option number or option name. The IPv6 option name space is disjoint from the IPv4 option name space. IPv6 addresses in options must be bracketed with square brackets, eg. --dhcp-option=option6:ntp-server,[1234::56]. For IPv6, [::] means "the global address of the machine running dnsmasq", whilst [fd00::] is replaced with the ULA, if it exists, and [fe80::] with the link-local address. Be careful: data-type suitability for the option number sent is not checked. It is quite possible to persuade dnsmasq to gener- ate illegal DHCP packets with injudicious use of this flag. When the value is a decimal number, dnsmasq must determine how large the data item is. It does this by examining the option number and/or the value, but can be overridden by appending a single letter flag as follows: b = one byte, s = two bytes, i = four bytes. This is mainly useful with encapsulated vendor class options (see below) where dnsmasq cannot determine data size from the option number. Option data which consists solely of pe- riods and digits will be interpreted by dnsmasq as an IP ad- dress, and inserted into an option as such. To force a literal string, use quotes. For instance when using option 66 to send a literal IP address as TFTP server name, it is necessary to do --dhcp-option=66,"1.2.3.4". Encapsulated Vendor-class options may also be specified (IPv4 only) using --dhcp-option: for instance --dhcp-option=vendor:PX- EClient,1,0.0.0.0 sends the encapsulated vendor class-specific option "mftp-address=0.0.0.0" to any client whose vendor-class matches "PXEClient". The vendor-class matching is substring based (see --dhcp-vendorclass for details). If a vendor-class option (number 60) is sent by dnsmasq, then that is used for se- lecting encapsulated options in preference to any sent by the client. It is possible to omit the vendorclass completely; --dhcp-option=vendor:,1,0.0.0.0 in which case the encapsulated option is always sent. Options may be encapsulated (IPv4 only) within other options: for instance --dhcp-option=encap:175, 190, iscsi-client0 will send option 175, within which is the option 190. If multiple op- tions are given which are encapsulated with the same option num- ber then they will be correctly combined into one encapsulated option. encap: and vendor: may not both be set in the same --dhcp-option. The final variant on encapsulated options is "Vendor-Identifying Vendor Options" as specified by RFC3925. These are denoted like this: --dhcp-option=vi-encap:2, 10, text The number in the vi- encap: section is the IANA enterprise number used to identify this option. This form of encapsulation is supported in IPv6. The address 0.0.0.0 is not treated specially in encapsulated op- tions. --dhcp-option-force=[tag:<tag>,[tag:<tag>,]][encap:<opt>,][vi-en- cap:<enterprise>,][vendor:[<vendor-class>],]<opt>,[<value>[,<value>]] This works in exactly the same way as --dhcp-option except that the option will always be sent, even if the client does not ask for it in the parameter request list. This is sometimes needed, for example when sending options to PXELinux. --dhcp-option-pxe=[tag:<tag>,[tag:<tag>,]][encap:<opt>,][vi-encap:<en- terprise>,]<opt>,[<value>[,<value>]] A variant of --dhcp-option which defines options only sent in reply to PXE clients. In addition, such options are sent in re- ply to PXE clients when dnsmasq is acting as a PXE proxy, unlike other options. A typical use-case is option 175, sent to iPXE. --dhcp-no-override (IPv4 only) Disable re-use of the DHCP servername and filename fields as extra option space. If it can, dnsmasq moves the boot server and filename information (from --dhcp-boot) out of their dedicated fields into DHCP options. This make extra space avail- able in the DHCP packet for options but can, rarely, confuse old or broken clients. This flag forces "simple and safe" behaviour to avoid problems in such a case. --leasequery[=<addr>[/<prefix>]] Enable RFC 4388 leasequery. The dnsmasq DHCP server will answer LEASEQUERY messages from DHCP relays when this option is given. If an address or subnet is given, only queries from a relay at that source are allowed. Repeat the --leasequery option to spec- ify multiple allowed sources. To correctly answer lease queries it is necessary to store extra data in the lease database, and this is also enabled by the --leasequery option. The extra fields (agent-info and vendorclass) are stored in the leases file in a somewhat backwards compatible manner. Enabling and then disabling leasequery will not cause problems; the extra in- formation will be aged out of the database. However, enabling leasequery in release 2.92 or later, storing leases which come via DHCP relays which add option-82 agent-info data, and then moving back to a pre-2.92 dnsmasq binary may cause problems reading the leases file. As of release 2.92, leasequery is only supported for DHCPv4. --dhcp-relay=<local address>[,<server address>[#<server port>]][,<in- terface] Configure dnsmasq to do DHCP relay. The local address is an ad- dress allocated to an interface on the host running dnsmasq. All DHCP requests arriving on that interface will be relayed to a remote DHCP server at the server address. It is possible to re- lay from a single local address to multiple remote servers by using multiple --dhcp-relay configs with the same local address and different server addresses. A server address must be an IP literal address, not a domain name. If the server address is omitted, the request will be forwarded by broadcast (IPv4) or multicast (IPv6). In this case the interface must be given and not be wildcard. The server address may specify a non-standard port to relay to. If this is used then --dhcp-proxy should likely also be set, otherwise parts of the DHCP conversation which do not pass through the relay will be delivered to the wrong port. Access control for DHCP clients has the same rules as for the DHCP server, see --interface, --except-interface, etc. The op- tional interface name in the --dhcp-relay config has a different function: it controls on which interface DHCP replies from the server will be accepted. This is intended for configurations which have three interfaces: one being relayed from, a second connecting the DHCP server, and a third untrusted network, typi- cally the wider internet. It avoids the possibility of spoof replies arriving via this third interface. It is allowed to have dnsmasq act as a DHCP server on one set of interfaces and relay from a disjoint set of interfaces. Note that whilst it is quite possible to write configurations which appear to act as a server and a relay on the same interface, this is not supported: the relay function will take precedence. Both DHCPv4 and DHCPv6 relay is supported. It's not possible to relay DHCPv4 to a DHCPv6 server or vice-versa. The DHCP relay function for IPv6 includes the ability to snoop prefix-delegation from relayed DHCP transactions. See --dhcp- script for details. --dhcp-split-relay=<local address>,[<server address>[#<server port>]],<server-facing-interface>|<server-facing-address> A usefully enhanced version of DHCPv4 relay. IPv4 DHCP normally uses a single address for two functions; it is used by the DHCP server to determine which network to allocate an address on, and it is used as the address of the relay to which the server sends packets. This version of DHCP relay splits these functions. It uses the address of the server-facing relay interface or a directly-spec- ified address as the address that the server talks to. The ad- dress of the client-facing interface (the first item in the con- fig) is used as to determine the client's subnet. The local ad- dress is also used as server-ID override so that the client al- ways sends requests via the relay. The effect of this is that server doesn't require a route to the client network and the clients don't require a route to the server. The third parameter is mandatory. If it is an interface name it cannot be a wildcard and the same filtering as described in --dhcp-relay applies; answers from the server must arrve via the specified interface. If the third parameter is an IP address it must be an address of a local interface which is routable from the server; In this case no filtering is done, the reply packets can arrive via any route. If setting up a network where the client networks have limited routing, be careful about configuring the DHCP server. Dnsmasq, as DHCP server, will set the default route to the client-facing relay interface unless explicitly configured: that is a sensible default. The normal default DNS server (the same address as the DHCP server) will not be appropriate when there is no route bew- teen the two, so this will have to be explicitly configured. -U, --dhcp-vendorclass=set:<tag>,[enterprise:<IANA-enterprise num- ber>,]<vendor-class> Map from a vendor-class string to a tag. Most DHCP clients pro- vide a "vendor class" which represents, in some sense, the type of host. This option maps vendor classes to tags, so that DHCP options may be selectively delivered to different classes of hosts. For example --dhcp-vendorclass=set:printers,Hewlett- Packard JetDirect will allow options to be set only for HP printers like so: --dhcp-option=tag:printers,3,192.168.4.4 The vendor-class string is substring matched against the vendor- class supplied by the client, to allow fuzzy matching. The set: prefix is optional but allowed for consistency. Note that in IPv6 only, vendorclasses are namespaced with an IANA-allocated enterprise number. This is given with enterprise: keyword and specifies that only vendorclasses matching the spec- ified number should be searched. -j, --dhcp-userclass=set:<tag>,<user-class> Map from a user-class string to a tag (with substring matching, like vendor classes). Most DHCP clients provide a "user class" which is configurable. This option maps user classes to tags, so that DHCP options may be selectively delivered to different classes of hosts. It is possible, for instance to use this to set a different printer server for hosts in the class "accounts" than for hosts in the class "engineering". -4, --dhcp-mac=set:<tag>,<MAC address> Map from a MAC address to a tag. The MAC address may include wildcards. For example --dhcp-mac=set:3com,01:34:23:*:*:* will set the tag "3com" for any host whose MAC address matches the pattern. --dhcp-circuitid=set:<tag>,<circuit-id>, --dhcp-remoteid=set:<tag>,<re- mote-id> Map from RFC3046 relay agent options to tags. This data may be provided by DHCP relay agents. The circuit-id or remote-id is normally given as colon-separated hex, but is also allowed to be a simple string. If an exact match is achieved between the cir- cuit or agent ID and one provided by a relay agent, the tag is set. --dhcp-remoteid (but not --dhcp-circuitid) is supported in IPv6. --dhcp-subscrid=set:<tag>,<subscriber-id> (IPv4 and IPv6) Map from RFC3993 subscriber-id relay agent op- tions to tags. --dhcp-proxy[=<ip addr>]...... (IPv4 only) A normal DHCP relay agent is only used to forward the initial parts of a DHCP interaction to the DHCP server. Once a client is configured, it communicates directly with the server. This is undesirable if the relay agent is adding extra information to the DHCP packets, such as that used by --dhcp- circuitid and --dhcp-remoteid. A full relay implementation can use the RFC 5107 serverid-override option to force the DHCP server to use the relay as a full proxy, with all packets pass- ing through it. This flag provides an alternative method of do- ing the same thing, for relays which don't support RFC 5107. Given alone, it manipulates the server-id for all interactions via relays. If a list of IP addresses is given, only interac- tions via relays at those addresses are affected. --dhcp-match=set:<tag>,<option number>|option:<option name>|vi-en- cap:<enterprise>[,<value>] Without <value>, set <tag> if the client sends a DHCP option of the given number or name. With <value>, set <tag> only if the client sends the option matching or containing <value>. The value may be of the form "01:ff:*:02" in which case the value must match (apart from wildcards) but the option sent may have unmatched data past the end of the value. The value may also be of the same form as in --dhcp-option in which case the option sent is treated as an array, and one element must match. --dhcp-match=set:efi-ia32,option:client-arch,6 sets the tag efi- ia32 if the number 6 appears in the list of architectures sent by the client in option 93. (See RFC 4578 for details.) If the value is a string, substring matching is used. The special form with vi-encap:<enterprise number> matches against vendor-identifying vendor classes for the specified en- terprise. Please see RFC 3925 for more details of these rare and interesting beasts. --dhcp-name-match=set:<tag>,<name>[*] Set a <tag> if the given <name> is supplied by a DHCP client. There may be a single trailing wildcard *, with a glob meaning. Combined with dhcp-ignore or dhcp-ignore-names this gives the ability to ignore certain clients by name, or disallow certain hostnames from being claimed by a client. --tag-if=set:<tag>[,set:<tag>[,tag:<tag>[,tag:<tag>]]] Perform boolean operations on tags. All set:<tag> tags are set if all tag:<tag> are already set, (or unset when tag:!<tag> is used). If no tag:<tag> appears, set:<tag> tags are set uncondi- tionally. Any number of set: and tag: forms may appear, in any order. --tag-if lines are executed in order, so if the tag in tag:<tag> is a tag set by another --tag-if, the line which sets the tag must precede the line which tests it. As an extension, the tag:<tag> clauses support limited wildcard matching, similar to the matching in the --interface directive. This allows the example --tag-if=set:ppp,tag:ppp* to set the tag 'ppp' for all requests received on any matching interface (ppp0, ppp1, etc). This can be used in conjunction with the tag:!<tag> format meaning that no tag matching the wildcard may be set. -J, --dhcp-ignore=tag:<tag>[,tag:<tag>] When all the given tags appear in the tag set, ignore the host and do not allocate it a DHCP lease. --dhcp-ignore-names[=tag:<tag>[,tag:<tag>]] When all the given tags appear in the tag set, ignore any host- name provided by the host. Note that, unlike --dhcp-ignore, it is permissible to supply no tags, in which case DHCP-client sup- plied hostnames are always ignored, and DHCP hosts are added to the DNS using only --dhcp-host configuration in dnsmasq and the contents of /etc/hosts and /etc/ethers. --dhcp-generate-names=tag:<tag>[,tag:<tag>] (IPv4 only) Generate a name for DHCP clients which do not other- wise have one, using the MAC address expressed in hex, separated by dashes. Note that if a host provides a name, it will be used by preference to this, unless --dhcp-ignore-names is set. --dhcp-broadcast[=tag:<tag>[,tag:<tag>]] (IPv4 only) When all the given tags appear in the tag set, al- ways use broadcast to communicate with the host when it is un- configured. It is permissible to supply no tags, in which case this is unconditional. Most DHCP clients which need broadcast replies set a flag in their requests so that this happens auto- matically, some old BOOTP clients do not. -M, --dhcp-boot=[tag:<tag>,]<filename>,[<servername>[,<server ad- dress>|<tftp_servername>]] (IPv4 only) Set BOOTP options to be returned by the DHCP server. Server name and address are optional: if not provided, the name is left empty, and the address set to the address of the machine running dnsmasq. If dnsmasq is providing a TFTP service (see --enable-tftp ) then only the filename is required here to en- able network booting. If the optional tag(s) are given, they must match for this configuration to be sent. Instead of an IP address, the TFTP server address can be given as a domain name which is looked up in /etc/hosts. This name can be associated in /etc/hosts with multiple IP addresses, which are used round- robin. This facility can be used to load balance the tftp load among a set of servers. --dhcp-sequential-ip Dnsmasq is designed to choose IP addresses for DHCP clients us- ing a hash of the client's MAC address. This normally allows a client's address to remain stable long-term, even if the client sometimes allows its DHCP lease to expire. In this default mode IP addresses are distributed pseudo-randomly over the entire available address range. There are sometimes circumstances (typ- ically server deployment) where it is more convenient to have IP addresses allocated sequentially, starting from the lowest available address, and setting this flag enables this mode. Note that in the sequential mode, clients which allow a lease to ex- pire are much more likely to move IP address; for this reason it should not be generally used. --dhcp-ignore-clid Dnsmasq is reading 'client identifier' (RFC 2131) option sent by clients (if available) to identify clients. This allow one to serve same IP address for a host using several interfaces. Use this option to disable 'client identifier' reading, i.e. to al- ways identify a host using the MAC address. --pxe-service=[tag:<tag>,]<CSA>,<menu text>[,<basename>|<bootservice- type>][,<server address>|<server_name>] Most uses of PXE boot-ROMS simply allow the PXE system to obtain an IP address and then download the file specified by --dhcp- boot and execute it. However the PXE system is capable of more complex functions when supported by a suitable DHCP server. This specifies a boot option which may appear in a PXE boot menu. <CSA> is client system type, only services of the correct type will appear in a menu. The known types are x86PC, PC98, IA64_EFI, Alpha, Arc_x86, Intel_Lean_Client, IA32_EFI, x86-64_EFI, Xscale_EFI, BC_EFI, ARM32_EFI and ARM64_EFI; an in- teger may be used for other types. The parameter after the menu text may be a file name, in which case dnsmasq acts as a boot server and directs the PXE client to download the file by TFTP, either from itself ( --enable-tftp must be set for this to work) or another TFTP server if the final server address/name is given. Note that the "layer" suffix (normally ".0") is supplied by PXE, and need not be added to the basename. Alternatively, the basename may be a filename, complete with suffix, in which case no layer suffix is added. If an integer boot service type, rather than a basename is given, then the PXE client will search for a suitable boot service for that type on the network. This search may be done by broadcast, or direct to a server if its IP address/name is provided. If no boot service type or filename is provided (or a boot service type of 0 is specified) then the menu entry will abort the net boot procedure and continue boot- ing from local media. The server address can be given as a do- main name which is looked up in /etc/hosts. This name can be as- sociated in /etc/hosts with multiple IP addresses, which are used round-robin. --pxe-prompt=[tag:<tag>,]<prompt>[,<timeout>] Setting this provides a prompt to be displayed after PXE boot. If the timeout is given then after the timeout has elapsed with no keyboard input, the first available menu option will be auto- matically executed. If the timeout is zero then the first avail- able menu item will be executed immediately. If --pxe-prompt is omitted the system will wait for user input if there are multi- ple items in the menu, but boot immediately if there is only one. See --pxe-service for details of menu items. Dnsmasq supports PXE "proxy-DHCP", in this case another DHCP server on the network is responsible for allocating IP ad- dresses, and dnsmasq simply provides the information given in --pxe-prompt and --pxe-service to allow netbooting. This mode is enabled using the proxy keyword in --dhcp-range. If the "other" DHCP server is on a remote network, it is possible, and useful, to configure dnsmasq as both a PXE proxy-DHCP server and a DHCP relay to the remote DHCP server. See --dhcp-relay for details. PXE is only supported over IPv4 at this time. --dhcp-pxe-vendor=<vendor>[,...] According to UEFI and PXE specifications, DHCP packets between PXE clients and proxy PXE servers should have PXEClient in their vendor-class field. However, the firmware of computers from a few vendors is customized to carry a different identifier in that field. This option is used to consider such identifiers valid for identifying PXE clients. For instance --dhcp-pxe-vendor=PXEClient,HW-Client will enable dnsmasq to also provide proxy PXE service to those PXE clients with HW-Client in as their identifier. -X, --dhcp-lease-max=<number> Limits dnsmasq to the specified maximum number of DHCP leases. The default is 1000. This limit is to prevent DoS attacks from hosts which create thousands of leases and use lots of memory in the dnsmasq process. -K, --dhcp-authoritative Should be set when dnsmasq is definitely the only DHCP server on a network. For DHCPv4, it changes the behaviour from strict RFC compliance so that DHCP requests on unknown leases from unknown hosts are not ignored. This allows new hosts to get a lease without a tedious timeout under all circumstances. It also al- lows dnsmasq to rebuild its lease database without each client needing to reacquire a lease, if the database is lost. For DHCPv6 it controls the same behaviour as DHCPv4 with missing leases (except for the RFC uncompliance - the DHCPv6 RFCs allow this behaviour if configured). It also sets the priority in replies to 255 (the maximum) instead of 0 (the minimum). --dhcp-rapid-commit Enable DHCPv4 Rapid Commit Option specified in RFC 4039. When enabled, dnsmasq will respond to a DHCPDISCOVER message includ- ing a Rapid Commit option with a DHCPACK including a Rapid Com- mit option and fully committed address and configuration infor- mation. Should only be enabled if either the server is the only server for the subnet, or multiple servers are present and they each commit a binding for all clients. --dhcp-alternate-port[=<server port>[,<client port>]] (IPv4 only) Change the ports used for DHCP from the default. If this option is given alone, without arguments, it changes the ports used for DHCP from 67 and 68 to 1067 and 1068. If a single argument is given, that port number is used for the server and the port number plus one used for the client. Finally, two port numbers allows arbitrary specification of both server and client ports for DHCP. -3, --bootp-dynamic[=<network-id>[,<network-id>]] (IPv4 only) Enable dynamic allocation of IP addresses to BOOTP clients. Use this with care, since each address allocated to a BOOTP client is leased forever, and therefore becomes perma- nently unavailable for re-use by other hosts. if this is given without tags, then it unconditionally enables dynamic alloca- tion. With tags, only when the tags are all set. It may be re- peated with different tag sets. -5, --no-ping (IPv4 only) By default, the DHCP server will attempt to ensure that an address is not in use before allocating it to a host. It does this by sending an ICMP echo request (aka "ping") to the address in question. If it gets a reply, then the address must already be in use, and another is tried. This flag disables this check. Use with caution. --log-dhcp Extra logging for DHCP: log all the options sent to DHCP clients and the tags used to determine them. --quiet-dhcp, --quiet-dhcp6, --quiet-ra, --quiet-tftp Suppress logging of the routine operation of these protocols. Errors and problems will still be logged. --quiet-tftp does not consider file not found to be an error. --quiet-dhcp and quiet- dhcp6 are over-ridden by --log-dhcp. -l, --dhcp-leasefile=<path> Use the specified file to store DHCP lease information. --dhcp-duid=<enterprise-id>,<uid> (IPv6 only) Specify the server persistent UID which the DHCPv6 server will use. This option is not normally required as dnsmasq creates a DUID automatically when it is first needed. When given, this option provides dnsmasq the data required to create a DUID-EN type DUID. Note that once set, the DUID is stored in the lease database, so to change between DUID-EN and automati- cally created DUIDs or vice-versa, the lease database must be re-initialised. The enterprise-id is assigned by IANA, and the uid is a string of hex octets unique to a particular device. -6 --dhcp-script=<path> Whenever a new DHCP lease is created, or an old one destroyed, or a TFTP file transfer completes, the executable specified by this option is run. <path> must be an absolute pathname, no PATH search occurs. The arguments to the process are "add", "old" or "del", the MAC address of the host (or DUID for IPv6) , the IP address, and the hostname, if known. "add" means a lease has been created, "del" means it has been destroyed, "old" is a notification of an existing lease when dnsmasq starts or a change to MAC address or hostname of an existing lease (also, lease length or expiry and client-id, if --leasefile-ro is set and lease expiry if --script-on-renewal is set). If the MAC ad- dress is from a network type other than ethernet, it will have the network type prepended, eg "06-01:23:45:67:89:ab" for token ring. The process is run as root (assuming that dnsmasq was originally run as root) even if dnsmasq is configured to change UID to an unprivileged user. The environment is inherited from the invoker of dnsmasq, with some or all of the following variables added For both IPv4 and IPv6: DNSMASQ_DOMAIN if the fully-qualified domain name of the host is known, this is set to the domain part. (Note that the hostname passed to the script as an argument is never fully-qualified.) If the client provides a hostname, DNSMASQ_SUPPLIED_HOSTNAME If the client provides user-classes, DNSMASQ_USER_CLASS0..DNS- MASQ_USER_CLASSn If dnsmasq was compiled with HAVE_BROKEN_RTC, then the length of the lease (in seconds) is stored in DNSMASQ_LEASE_LENGTH, other- wise the time of lease expiry is stored in DNSMASQ_LEASE_EX- PIRES. The number of seconds until lease expiry is always stored in DNSMASQ_TIME_REMAINING. DNSMASQ_DATA_MISSING is set to "1" during "old" events for ex- isting leases generated at startup to indicate that data not stored in the persistent lease database will not be present. This comprises everything other than IP address, hostname, MAC address, DUID, IAID and lease length or expiry time. If a lease used to have a hostname, which is removed, an "old" event is generated with the new state of the lease, ie no name, and the former name is provided in the environment variable DNS- MASQ_OLD_HOSTNAME. DNSMASQ_INTERFACE stores the name of the interface on which the request arrived; this is not set for "old" actions when dnsmasq restarts. DNSMASQ_RELAY_ADDRESS is set if the client used a DHCP relay to contact dnsmasq and the IP address of the relay is known. DNSMASQ_TAGS contains all the tags set during the DHCP transac- tion, separated by spaces. DNSMASQ_LOG_DHCP is set if --log-dhcp is in effect. DNSMASQ_REQUESTED_OPTIONS a string containing the decimal values in the Parameter Request List option, comma separated, if the parameter request list option is provided by the client. DNSMASQ_MUD_URL the Manufacturer Usage Description URL if pro- vided by the client. (See RFC8520 for details.) For IPv4 only: DNSMASQ_CLIENT_ID if the host provided a client-id. DNSMASQ_CIRCUIT_ID, DNSMASQ_SUBSCRIBER_ID, DNSMASQ_REMOTE_ID if a DHCP relay-agent added any of these options. If the client provides vendor-class, DNSMASQ_VENDOR_CLASS. For IPv6 only: If the client provides vendor-class, DNSMASQ_VENDOR_CLASS_ID, containing the IANA enterprise id for the class, and DNS- MASQ_VENDOR_CLASS0..DNSMASQ_VENDOR_CLASSn for the data. DNSMASQ_SERVER_DUID containing the DUID of the server: this is the same for every call to the script. DNSMASQ_IAID containing the IAID for the lease. If the lease is a temporary allocation, this is prefixed to 'T'. DNSMASQ_MAC containing the MAC address of the client, if known. Note that the supplied hostname, vendorclass and userclass data is only supplied for "add" actions or "old" actions when a host resumes an existing lease, since these data are not held in dns- masq's lease database. All file descriptors are closed except stdin, which is open to /dev/null, and stdout and stderr which capture output for log- ging by dnsmasq. (In debug mode, stdio, stdout and stderr file are left as those inherited from the invoker of dnsmasq). The script is not invoked concurrently: at most one instance of the script is ever running (dnsmasq waits for an instance of script to exit before running the next). Changes to the lease database are which require the script to be invoked are queued awaiting exit of a running instance. If this queueing allows multiple state changes occur to a single lease before the script can be run then earlier states are discarded and the current state of that lease is reflected when the script finally runs. At dnsmasq startup, the script will be invoked for all existing leases as they are read from the lease file. Expired leases will be called with "del" and others with "old". When dnsmasq re- ceives a HUP signal, the script will be invoked for existing leases with an "old" event. There are five further actions which may appear as the first ar- gument to the script, "init", "arp-add", "arp-del", "relay- snoop" and "tftp". More may be added in the future, so scripts should be written to ignore unknown actions. "init" is described below in --leasefile-ro The "tftp" action is invoked when a TFTP file transfer com- pletes: the arguments are the file size in bytes, the address to which the file was sent, and the complete pathname of the file. The "relay-snoop" action is invoked when dnsmasq is configured as a DHCP relay for DHCPv6 and it relays a prefx delegation to a client. The arguments are the name of the interface where the client is connected, its (link-local) address on that interface and the delegated prefix. This information is sufficient to in- stall routes to the delegated prefix of a router. See --dhcp-re- lay for more details on configuring DHCP relay. The "arp-add" and "arp-del" actions are only called if enabled with --script-arp They are are supplied with a MAC address and IP address as arguments. "arp-add" indicates the arrival of a new entry in the ARP or neighbour table, and "arp-del" indicates the deletion of same. --dhcp-luascript=<path> Specify a script written in Lua, to be run when leases are cre- ated, destroyed or changed. To use this option, dnsmasq must be compiled with the correct support. The Lua interpreter is ini- tialised once, when dnsmasq starts, so that global variables persist between lease events. The Lua code must define a lease function, and may provide init and shutdown functions, which are called, without arguments when dnsmasq starts up and terminates. It may also provide a tftp function. The lease function receives the information detailed in --dhcp- script. It gets two arguments, firstly the action, which is a string containing, "add", "old" or "del", and secondly a table of tag value pairs. The tags mostly correspond to the environ- ment variables detailed above, for instance the tag "domain" holds the same data as the environment variable DNSMASQ_DOMAIN. There are a few extra tags which hold the data supplied as argu- ments to --dhcp-script. These are mac_address, ip_address and hostname for IPv4, and client_duid, ip_address and hostname for IPv6. The tftp function is called in the same way as the lease func- tion, and the table holds the tags destination_address, file_name and file_size. The arp and arp-old functions are called only when enabled with --script-arp and have a table which holds the tags mac_address and client_address. --dhcp-scriptuser Specify the user as which to run the lease-change script or Lua script. This defaults to root, but can be changed to another user using this flag. --script-arp Enable the "arp" and "arp-old" functions in the --dhcp-script and --dhcp-luascript. -9, --leasefile-ro Completely suppress use of the lease database file. The file will not be created, read, or written. Change the way the lease- change script (if one is provided) is called, so that the lease database may be maintained in external storage by the script. In addition to the invocations given in --dhcp-script the lease- change script is called once, at dnsmasq startup, with the sin- gle argument "init". When called like this the script should write the saved state of the lease database, in dnsmasq lease- file format, to stdout and exit with zero exit code. Setting this option also forces the leasechange script to be called on changes to the client-id and lease length and expiry time. --script-on-renewal Call the DHCP script when the lease expiry time changes, for in- stance when the lease is renewed. --bridge-interface=<interface>,<alias>[,<alias>] Treat DHCP (v4 and v6) requests and IPv6 Router Solicit packets arriving at any of the <alias> interfaces as if they had arrived at <interface>. This option allows dnsmasq to provide DHCP and RA service over unaddressed and unbridged Ethernet interfaces, e.g. on an OpenStack compute host where each such interface is a TAP interface to a VM, or as in "old style bridging" on BSD platforms. A trailing '*' wildcard can be used in each <alias>. It is permissible to add more than one alias using more than one --bridge-interface option since --bridge-inter- face=int1,alias1,alias2 is exactly equivalent to --bridge-inter- face=int1,alias1 --bridge-interface=int1,alias2 --shared-network=<interface>,<addr> --shared-network=<addr>,<addr> The DHCP server determines which DHCP ranges are useable for al- locating an address to a DHCP client based on the network from which the DHCP request arrives, and the IP configuration of the server's interface on that network. The shared-network option extends the available subnets (and therefore DHCP ranges) beyond the subnets configured on the arrival interface. The first argument is either the name of an interface, or an ad- dress that is configured on a local interface, and the second argument is an address which defines another subnet on which ad- dresses can be allocated. To be useful, there must be a suitable dhcp-range which allows address allocation on this subnet and this dhcp-range MUST in- clude the netmask. Using shared-network also needs extra consideration of routing. Dnsmasq does not have the usual information that it uses to de- termine the default route, so the default route option (or other routing) MUST be configured manually. The client must have a route to the server: if the two-address form of shared-network is used, this needs to be to the first specified address. If the interface,address form is used, there must be a route to all of the addresses configured on the interface. The two-address form of shared-network is also usable with a DHCP relay: the first address is the address of the relay and the second, as before, specifies an extra subnet which addresses may be allocated from. -s, --domain=<domain>[[,<address range>[,local]]|<interface>] Specifies DNS domains for the DHCP server. Domains may be be given unconditionally (without the IP range) or for limited IP ranges. This has two effects; firstly it causes the DHCP server to return the domain to any hosts which request it, and secondly it sets the domain which it is legal for DHCP-configured hosts to claim. The intention is to constrain hostnames so that an un- trusted host on the LAN cannot advertise its name via DHCP as e.g. "microsoft.com" and capture traffic not meant for it. If no domain suffix is specified, then any DHCP hostname with a domain part (ie with a period) will be disallowed and logged. If suffix is specified, then hostnames with a domain part are allowed, provided the domain part matches the suffix. In addition, when a suffix is set then hostnames without a domain part have the suf- fix added as an optional domain part. Eg on my network I can set --domain=thekelleys.org.uk and have a machine whose DHCP host- name is "laptop". The IP address for that machine is available from dnsmasq both as "laptop" and "laptop.thekelleys.org.uk". If the domain is given as "#" then the domain is read from the first "search" directive in /etc/resolv.conf (or equivalent). The address range can be of the form <ip address>,<ip address> or <ip address>/<netmask> or just a single <ip address>. See --dhcp-fqdn which can change the behaviour of dnsmasq with do- mains. If the address range is given as ip-address/network-size, then a additional flag "local" may be supplied which has the effect of adding --local declarations for forward and reverse DNS queries. Eg. --domain=thekelleys.org.uk,192.168.0.0/24,local is identi- cal to --domain=thekelleys.org.uk,192.168.0.0/24 --lo- cal=/thekelleys.org.uk/ --local=/0.168.192.in-addr.arpa/ The address range can also be given as a network interface name, in which case all of the subnets currently assigned to the in- terface are used in matching the address. This allows hosts on different physical subnets to be given different domains in a way which updates automatically as the interface addresses change. --dhcp-fqdn In the default mode, dnsmasq inserts the unqualified names of DHCP clients into the DNS. For this reason, the names must be unique, even if two clients which have the same name are in dif- ferent domains. If a second DHCP client appears which has the same name as an existing client, the name is transferred to the new client. If --dhcp-fqdn is set, this behaviour changes: the unqualified name is no longer put in the DNS, only the qualified name. Two DHCP clients with the same name may both keep the name, provided that the domain part is different (ie the fully qualified names differ.) To ensure that all names have a domain part, there must be at least --domain without an address speci- fied when --dhcp-fqdn is set. --dhcp-client-update Normally, when giving a DHCP lease, dnsmasq sets flags in the FQDN option to tell the client not to attempt a DDNS update with its name and IP address. This is because the name-IP pair is au- tomatically added into dnsmasq's DNS view. This flag suppresses that behaviour, this is useful, for instance, to allow Windows clients to update Active Directory servers. See RFC 4702 for de- tails. --enable-ra Enable dnsmasq's IPv6 Router Advertisement feature. DHCPv6 doesn't handle complete network configuration in the same way as DHCPv4. Router discovery and (possibly) prefix discovery for au- tonomous address creation are handled by a different protocol. When DHCP is in use, only a subset of this is needed, and dns- masq can handle it, using existing DHCP configuration to provide most data. When RA is enabled, dnsmasq will advertise a prefix for each --dhcp-range, with default router as the relevant link-local address on the machine running dnsmasq. By default, the "managed address" bits are set, and the "use SLAAC" bit is reset. This can be changed for individual subnets with the mode keywords described in --dhcp-range. RFC6106 DNS parameters are included in the advertisements. By default, the relevant link- local address of the machine running dnsmasq is sent as recur- sive DNS server. If provided, the DHCPv6 options dns-server and domain-search are used for the DNS server (RDNSS) and the domain search list (DNSSL). --ra-param=<interface>,[mtu:<integer>|<interface>|off,][high,|low,]<ra- interval>[,<router lifetime>] Set non-default values for router advertisements sent via an in- terface. The priority field for the router may be altered from the default of medium with eg --ra-param=eth0,high. The inter- val between router advertisements may be set (in seconds) with --ra-param=eth0,60. The lifetime of the route may be changed or set to zero, which allows a router to advertise prefixes but not a route via itself. --ra-param=eth0,0,0 (A value of zero for the interval means the default value.) All four parameters may be set at once. --ra-param=eth0,mtu:1280,low,60,1200 The interface field may include a wildcard. The mtu: parameter may be an arbitrary interface name, in which case the MTU value for that interface is used. This is useful for (eg) advertising the MTU of a WAN interface on the other in- terfaces of a router. --dhcp-reply-delay=[tag:<tag>,]<integer> Delays sending DHCPOFFER and PROXYDHCP replies for at least the specified number of seconds. This can be used as workaround for bugs in PXE boot firmware that does not function properly when receiving an instant reply. This option takes into account the time already spent waiting (e.g. performing ping check) if any. --enable-tftp[=<interface>[,<interface>]] Enable the TFTP server function. This is deliberately limited to that needed to net-boot a client. Only reading is allowed; the tsize and blksize extensions are supported (tsize is only sup- ported in octet mode). Without an argument, the TFTP service is provided to the same set of interfaces as DHCP service. If the list of interfaces is provided, that defines which interfaces receive TFTP service. --tftp-root=<directory>[,<interface>] Look for files to transfer using TFTP relative to the given di- rectory. When this is set, TFTP paths which include ".." are re- jected, to stop clients getting outside the specified root. Ab- solute paths (starting with /) are allowed, but they must be within the tftp-root. If the optional interface argument is given, the directory is only used for TFTP requests via that in- terface. --tftp-no-fail Do not abort startup if specified tftp root directories are in- accessible. --tftp-unique-root[=ip|mac] Add the IP or hardware address of the TFTP client as a path com- ponent on the end of the TFTP-root. Only valid if a --tftp-root is set and the directory exists. Defaults to adding IP address (in standard dotted-quad format). For instance, if --tftp-root is "/tftp" and client 1.2.3.4 requests file "myfile" then the effective path will be "/tftp/1.2.3.4/myfile" if /tftp/1.2.3.4 exists or /tftp/myfile otherwise. When "=mac" is specified it will append the MAC address instead, using lowercase zero padded digits separated by dashes, e.g.: 01-02-03-04-aa-bb Note that resolving MAC addresses is only possible if the client is in the local network or obtained a DHCP lease from us. --tftp-secure Enable TFTP secure mode: without this, any file which is read- able by the dnsmasq process under normal unix access-control rules is available via TFTP. When the --tftp-secure flag is given, only files owned by the user running the dnsmasq process are accessible. If dnsmasq is being run as root, different rules apply: --tftp-secure has no effect, but only files which have the world-readable bit set are accessible. It is not recommended to run dnsmasq as root with TFTP enabled, and certainly not without specifying --tftp-root. Doing so can expose any world- readable file on the server to any host on the net. --tftp-lowercase Convert filenames in TFTP requests to all lowercase. This is useful for requests from Windows machines, which have case-in- sensitive filesystems and tend to play fast-and-loose with case in filenames. Note that dnsmasq's tftp server always converts "\" to "/" in filenames. --tftp-max=<connections> Set the maximum number of concurrent TFTP connections allowed. This defaults to 50. When serving a large number of TFTP connec- tions, per-process file descriptor limits may be encountered. Dnsmasq needs one file descriptor for each concurrent TFTP con- nection and one file descriptor per unique file (plus a few oth- ers). So serving the same file simultaneously to n clients will use require about n + 10 file descriptors, serving different files simultaneously to n clients will require about (2*n) + 10 descriptors. If --tftp-port-range is given, that can affect the number of concurrent connections. --tftp-mtu=<mtu size> Use size as the ceiling of the MTU supported by the intervening network when negotiating TFTP blocksize, overriding the MTU set- ting of the local interface if it is larger. --tftp-no-blocksize Stop the TFTP server from negotiating the "blocksize" option with a client. Some buggy clients request this option but then behave badly when it is granted. --tftp-port-range=<start>,<end> A TFTP server listens on a well-known port (69) for connection initiation, but it also uses a dynamically-allocated port for each connection. Normally these are allocated by the OS, but this option specifies a range of ports for use by TFTP trans- fers. This can be useful when TFTP has to traverse a firewall. The start of the range cannot be lower than 1025 unless dnsmasq is running as root. The number of concurrent TFTP connections is limited by the size of the port range. --tftp-single-port Run in a mode where the TFTP server uses ONLY the well-known port (69) for its end of the TFTP transfer. This allows TFTP to work when there in NAT is the path between client and server. Note that this is not strictly compliant with the RFCs specify- ing the TFTP protocol: use at your own risk. -C, --conf-file=<file> Specify a configuration file. The presence of this option stops dnsmasq from reading the default configuration file (normally /etc/dnsmasq.conf). Multiple files may be specified by repeating the option either on the command line or in configuration files. A filename of "-" causes dnsmasq to read configuration from stdin. -7, --conf-dir=<directory>[,<file-extension>......], Read all the files in the given directory as configuration files. If extension(s) are given, any files which end in those extensions are skipped. Any files whose names end in ~ or start with . or start and end with # are always skipped. If the exten- sion starts with * then only files which have that extension are loaded. So --conf-dir=/path/to/dir,*.conf loads all files with the suffix .conf in /path/to/dir. This flag may be given on the command line or in a configuration file. If giving it on the command line, be sure to escape * characters. Files are loaded in alphabetical order of filename. --servers-file=<file> A special case of --conf-file which differs in two respects. Firstly, only --server and --rev-server are allowed in the con- figuration file included. Secondly, the file is re-read and the configuration therein is updated when dnsmasq receives SIGHUP. --conf-script=<file>[ <arg] Execute <file>, and treat what it emits to stdout as the con- tents of a configuration file. If the script exits with a non- zero exit code, dnsmasq treats this as a fatal error. The script can be passed arguments, space separated from the file- name and each other so, for instance --conf-dir="/etc/dnsmasq- uncompress-ads /share/ads-domains.gz" with /etc/dnsmasq-uncompress-ads containing set -e zcat ${1} | sed -e "s:^:address=/:" -e "s:$:/:" exit 0 and /share/ads-domains.gz containing a compressed list of ad server domains will save disk space with large ad-server block- lists. --no-ident Do not respond to class CHAOS and type TXT in domain bind queries. Without this option being set, the cache statistics are also available in the DNS as answers to queries of class CHAOS and type TXT in domain bind. The domain names are cachesize.bind, insertions.bind, evictions.bind, misses.bind, hits.bind, auth.bind and servers.bind unless disabled at compile-time. An example command to query this, using the dig utility would be dig +short chaos txt cachesize.bind --max-tcp-connections=<number> The maximum number of concurrent TCP connections. The applica- tion forks to handle each TCP request. The default maximum is 20. CONFIG FILE At startup, dnsmasq reads /etc/dnsmasq.conf, if it exists. (On FreeBSD, the file is /usr/local/etc/dnsmasq.conf ) (but see the --conf-file and --conf-dir options.) The format of this file consists of one option per line, exactly as the long options detailed in the OPTIONS section but without the leading "--". Lines starting with # are comments and ig- nored. For options which may only be specified once, the configuration file overrides the command line. Quoting is allowed in a config file: between " quotes the special meanings of ,:. and # are removed and the following escapes are allowed: \\ \" \t \e \b \r and \n. The later cor- responding to tab, escape, backspace, return and newline. NOTES When it receives a SIGHUP, dnsmasq clears its cache and then re-loads /etc/hosts and /etc/ethers and any file given by --dhcp-hostsfile, --dhcp-hostsdir, --dhcp-optsfile, --dhcp-optsdir, --addn-hosts or --hostsdir. The DHCP lease change script is called for all existing DHCP leases. If --no-poll is set SIGHUP also re-reads /etc/resolv.conf. SIGHUP does NOT re-read the configuration file. When it receives a SIGUSR1, dnsmasq writes statistics to the system log. It writes the cache size, the number of names which have had to removed from the cache before they expired in order to make room for new names and the total number of names that have been inserted into the cache. The number of cache hits and misses and the number of au- thoritative queries answered are also given. For each upstream server it gives the number of queries sent, and the number which resulted in an error. It also gives information on the number of forks for TCP con- nections. In --no-daemon mode or when full logging is enabled (--log- queries), a complete dump of the contents of the cache is made. When it receives SIGUSR2 and it is logging direct to a file (see --log- facility ) dnsmasq will close and reopen the log file. Note that during this operation, dnsmasq will not be running as root. When it first cre- ates the logfile dnsmasq changes the ownership of the file to the non- root user it will run as. Logrotate should be configured to create a new log file with the ownership which matches the existing one before sending SIGUSR2. If TCP DNS queries are in progress, the old logfile will remain open in child processes which are handling TCP queries and may continue to be written. There is a limit of 150 seconds, after which all existing TCP processes will have expired: for this reason, it is not wise to configure logfile compression for logfiles which have just been rotated. Using logrotate, the required options are create and delaycompress. Dnsmasq is a DNS query forwarder: it is not capable of recursively an- swering arbitrary queries starting from the root servers but forwards such queries to a fully recursive upstream DNS server which is typi- cally provided by an ISP. By default, dnsmasq reads /etc/resolv.conf to discover the IP addresses of the upstream nameservers it should use, since the information is typically stored there. Unless --no-poll is used, dnsmasq checks the modification time of /etc/resolv.conf (or equivalent if --resolv-file is used) and re-reads it if it changes. This allows the DNS servers to be set dynamically by PPP or DHCP since both protocols provide the information. Absence of /etc/resolv.conf is not an error since it may not have been created before a PPP connection exists. Dnsmasq simply keeps checking in case /etc/resolv.conf is cre- ated at any time. Dnsmasq can be told to parse more than one re- solv.conf file. This is useful on a laptop, where both PPP and DHCP may be used: dnsmasq can be set to poll both /etc/ppp/resolv.conf and /etc/dhcpc/resolv.conf and will use the contents of whichever changed last, giving automatic switching between DNS servers. Upstream servers may also be specified on the command line or in the configuration file. These server specifications optionally take a do- main name which tells dnsmasq to use that server only to find names in that particular domain. In order to configure dnsmasq to act as cache for the host on which it is running, put "nameserver 127.0.0.1" in /etc/resolv.conf to force lo- cal processes to send queries to dnsmasq. Then either specify the up- stream servers directly to dnsmasq using --server options or put their addresses real in another file, say /etc/resolv.dnsmasq and run dnsmasq with the --resolv-file /etc/resolv.dnsmasq option. This second tech- nique allows for dynamic update of the server addresses by PPP or DHCP. Addresses in /etc/hosts will "shadow" different addresses for the same names in the upstream DNS, so "mycompany.com 1.2.3.4" in /etc/hosts will ensure that queries for "mycompany.com" always return 1.2.3.4 even if queries in the upstream DNS would otherwise return a different ad- dress. There is one exception to this: if the upstream DNS contains a CNAME which points to a shadowed name, then looking up the CNAME through dnsmasq will result in the unshadowed address associated with the target of the CNAME. To work around this, add the CNAME to /etc/hosts so that the CNAME is shadowed too. The tag system works as follows: dnsmasq tags each DHCP request with tags from applicable configuration lines containing set:<tag> i.e. set:<tag> from the --dhcp-range used to allocate the address; set:<tag> from any matching --dhcp-host (plus the tag known or known- othernet). BOOTP requests are tagged bootp. Each request is also tagged with the name of the interface on which the request arrived. Each configuration line containing one or more tag:<tag> constructs ap- plies when all its tags exist on the request. That is: Configuration tag:A applies to a request set:tagged A. Configuration tag:B applies to a request set:tagged B. Configuration tag:A+B doesn't apply to a request set:tagged A. Configuration tag:A+B doesn't apply to a request set:tagged B. Configurations tag:A+B, tag:A, tag:B apply to a request set:tagged A+B. set:<tag> constructs in --dhcp-range and --dhcp-host tag requests. Use tag:<tag>s in --dhcp-options to match set:<tag> and apply configu- rations. A --dhcp-option with tag:<tag> is preferred over an untagged --dhcp-op- tion, provided that all its tags match somewhere in the set gathered above. The tag prefix '!' means 'not'. --dhcp-option=tag:!purple,3,1.2.3.4 sends the option when the request is not tagged with purple. (The shell metacharacter '!' must be escaped on the command line but not in a con- figuration file). When selecting --dhcp-options, a --dhcp-range tag is second class to other tags, to make it easy to override options for individual hosts, so: --dhcp-range=set:interface1,...... --dhcp-host=set:myhost,..... --dhcp-option=tag:interface1,option:nis-domain,"domain1" --dhcp-option=tag:myhost,option:nis-domain,"domain2" sets the NIS-domain to domain1 for hosts in the range, but to domain2 for a particular host that may or may not fall in the range. Note that for --dhcp-range both tag:<tag> and set:<tag> are possible, in order to both select the range in use based on (eg) --dhcp-host, and to affect the options sent, based on the range selected. The tag system evolved from an earlier, more limited system. For back- ward compatibility, "net:" may be used instead of "tag:" and "set:" may be omitted. (Except in --dhcp-host, where "net:" may be used instead of "set:".) For the same reason, '#' may be used instead of '!' to indi- cate NOT. The DHCP server in dnsmasq will function as a BOOTP server also, pro- vided that the MAC address and IP address for clients are given, either using --dhcp-host configurations or in /etc/ethers , and a --dhcp-range configuration option is present to activate the DHCP server on a par- ticular network. (Setting --bootp-dynamic removes the need for static address mappings.) The filename parameter in a BOOTP request is used as a tag, as is the tag bootp, allowing some control over the options re- turned to different classes of hosts. AUTHORITATIVE CONFIGURATION Configuring dnsmasq to act as an authoritative DNS server is compli- cated by the fact that it involves configuration of external DNS servers to provide delegation. We will walk through three scenarios of increasing complexity. Prerequisites for all of these scenarios are a globally accessible IP address, an A or AAAA record pointing to that address, and an external DNS server capable of doing delegation of the zone in question. For the first part of this explanation, we will call the A (or AAAA) record for the globally accessible address server.exam- ple.com, and the zone for which dnsmasq is authoritative our.zone.com. The simplest configuration consists of two lines of dnsmasq configura- tion; something like --auth-server=server.example.com,eth0 --auth-zone=our.zone.com,1.2.3.0/24 and two records in the external DNS server.example.com A 192.0.43.10 our.zone.com NS server.example.com eth0 is the external network interface on which dnsmasq is listening, and has (globally accessible) address 192.0.43.10. Note that the external IP address may well be dynamic (ie assigned from an ISP by DHCP or PPP) If so, the A record must be linked to this dy- namic assignment by one of the usual dynamic-DNS systems. A more complex, but practically useful configuration has the address record for the globally accessible IP address residing in the authori- tative zone which dnsmasq is serving, typically at the root. Now we have --auth-server=our.zone.com,eth0 --auth-zone=our.zone.com,1.2.3.0/24 our.zone.com A 1.2.3.4 our.zone.com NS our.zone.com The A record for our.zone.com has now become a glue record, it solves the chicken-and-egg problem of finding the IP address of the nameserver for our.zone.com when the A record is within that zone. Note that this is the only role of this record: as dnsmasq is now authoritative from our.zone.com it too must provide this record. If the external address is static, this can be done with an /etc/hosts entry or --host-record. --auth-server=our.zone.com,eth0 --host-record=our.zone.com,1.2.3.4 --auth-zone=our.zone.com,1.2.3.0/24 If the external address is dynamic, the address associated with our.zone.com must be derived from the address of the relevant inter- face. This is done using --interface-name Something like: --auth-server=our.zone.com,eth0 --interface-name=our.zone.com,eth0 --auth-zone=our.zone.com,1.2.3.0/24,eth0 (The "eth0" argument in --auth-zone adds the subnet containing eth0's dynamic address to the zone, so that the --interface-name returns the address in outside queries.) Our final configuration builds on that above, but also adds a secondary DNS server. This is another DNS server which learns the DNS data for the zone by doing zones transfer, and acts as a backup should the pri- mary server become inaccessible. The configuration of the secondary is beyond the scope of this man-page, but the extra configuration of dns- masq is simple: --auth-sec-servers=secondary.myisp.com and our.zone.com NS secondary.myisp.com Adding auth-sec-servers enables zone transfer in dnsmasq, to allow the secondary to collect the DNS data. If you wish to restrict this data to particular hosts then --auth-peer=<IP address of secondary> will do so. Dnsmasq acts as an authoritative server for in-addr.arpa and ip6.arpa domains associated with the subnets given in --auth-zone declarations, so reverse (address to name) lookups can be simply configured with a suitable NS record, for instance in this example, where we allow 1.2.3.0/24 addresses. 3.2.1.in-addr.arpa NS our.zone.com Note that at present, reverse (in-addr.arpa and ip6.arpa) zones are not available in zone transfers, so there is no point arranging secondary servers for reverse lookups. When dnsmasq is configured to act as an authoritative server, the fol- lowing data is used to populate the authoritative zone. --mx-host, --srv-host, --dns-rr, --txt-record, --naptr-record, --caa- record, as long as the record names are in the authoritative domain. --synth-domain as long as the domain is in the authoritative zone and, for reverse (PTR) queries, the address is in the relevant subnet. --cname as long as the record name is in the authoritative domain. If the target of the CNAME is unqualified, then it is qualified with the authoritative zone name. CNAME used in this way (only) may be wild- cards, as in --cname=*.example.com,default.example.com IPv4 and IPv6 addresses from /etc/hosts (and --addn-hosts ) and --host- record and --interface-name and ---dynamic-host provided the address falls into one of the subnets specified in the --auth-zone. Addresses of DHCP leases, provided the address falls into one of the subnets specified in the --auth-zone. (If constructed DHCP ranges are is use, which depend on the address dynamically assigned to an inter- face, then the form of --auth-zone which defines subnets by the dynamic address of an interface should be used to ensure this condition is met.) In the default mode, where a DHCP lease has an unqualified name, and possibly a qualified name constructed using --domain then the name in the authoritative zone is constructed from the unqualified name and the zone's domain. This may or may not equal that specified by --domain. If --dhcp-fqdn is set, then the fully qualified names associated with DHCP leases are used, and must match the zone's domain. EXIT CODES 0 - Dnsmasq successfully forked into the background, or terminated nor- mally if backgrounding is not enabled. 1 - A problem with configuration was detected. 2 - A problem with network access occurred (address in use, attempt to use privileged ports without permission). 3 - A problem occurred with a filesystem operation (missing file/direc- tory, permissions). 4 - Memory allocation failure. 5 - Other miscellaneous problem. 11 or greater - a non zero return code was received from the lease- script process "init" call or a --conf-script file. The exit code from dnsmasq is the script's exit code with 10 added. LIMITS The default values for resource limits in dnsmasq are generally conser- vative, and appropriate for embedded router type devices with slow processors and limited memory. On more capable hardware, it is possible to increase the limits, and handle many more clients. The following ap- plies to dnsmasq-2.37: earlier versions did not scale as well. Dnsmasq is capable of handling DNS and DHCP for at least a thousand clients. The DHCP lease times should not be very short (less than one hour). The value of --dns-forward-max can be increased: start with it equal to the number of clients and increase if DNS seems slow. Note that DNS performance depends too on the performance of the upstream nameservers. The size of the DNS cache may be increased: the hard limit is 10000 names and the default (150) is very low. Sending SIGUSR1 to dnsmasq makes it log information which is useful for tuning the cache size. See the NOTES section for details. The built-in TFTP server is capable of many simultaneous file trans- fers: the absolute limit is related to the number of file-handles al- lowed to a process and the ability of the select() system call to cope with large numbers of file handles. If the limit is set too high using --tftp-max it will be scaled down and the actual limit logged at start- up. Note that more transfers are possible when the same file is being sent than when each transfer sends a different file. It is possible to use dnsmasq to block Web advertising by using a list of known banner-ad servers, all resolving to 127.0.0.1 or 0.0.0.0, in /etc/hosts or an additional hosts file. The list can be very long, dns- masq has been tested successfully with one million names. That size file needs a 1GHz processor and about 60Mb of RAM. INTERNATIONALISATION Dnsmasq can be compiled to support internationalisation. To do this, the make targets "all-i18n" and "install-i18n" should be used instead of the standard targets "all" and "install". When internationalisation is compiled in, dnsmasq will produce log messages in the local language and support internationalised domain names (IDN). Domain names in /etc/hosts, /etc/ethers and /etc/dnsmasq.conf which contain non-ASCII characters will be translated to the DNS-internal punycode representa- tion. Note that dnsmasq determines both the language for messages and the assumed charset for configuration files from the LANG environment variable. This should be set to the system default value by the script which is responsible for starting dnsmasq. When editing the configura- tion files, be careful to do so using only the system-default locale and not user-specific one, since dnsmasq has no direct way of determin- ing the charset in use, and must assume that it is the system default. FILES /etc/dnsmasq.conf /usr/local/etc/dnsmasq.conf /etc/resolv.conf /var/run/dnsmasq/resolv.conf /etc/ppp/resolv.conf /etc/dhcpc/resolv.conf /etc/hosts /etc/ethers /var/lib/misc/dnsmasq.leases /var/db/dnsmasq.leases /var/run/dnsmasq.pid SEE ALSO hosts(5), resolver(5) AUTHOR This manual page was written by Simon Kelley <simon@thekelleys.org.uk>. 2025-02-05 DNSMASQ(8)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | CONFIG FILE | NOTES | AUTHORITATIVE CONFIGURATION | EXIT CODES | LIMITS | INTERNATIONALISATION | FILES | SEE ALSO | AUTHOR
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=dnsmasq&manpath=FreeBSD+15.0-RELEASE+and+Ports.quarterly>