FreeBSD Manual Pages
MTR(8) System Administration MTR(8) NAME mtr - a network diagnostic tool SYNOPSIS mtr [-4|-6] [-F FILENAME] [--report] [--report-wide] [--xml] [--gtk] [--curses] [--displaymode MODE] [--raw] [--csv] [--json] [--split] [--no-dns] [--show-ips] [-o FIELDS] [-y IPINFO] [--aslookup] [--ip- info_provider4 DOMAIN] [--ipinfo_provider6 DOMAIN] [-i INTERVAL] [-c COUNT] [-s PACKETSIZE] [-B BITPATTERN] [-G GRACEPERIOD] [-Q TOS] [--mpls] [-I NAME] [-a ADDRESS] [-f FIRST-TTL] [-m MAX-TTL] [-U MAX-UN- KNOWN] [-E MAX-DISPLAY-PATH] [--udp] [--tcp] [--sctp] [-P PORT] [-L LO- CALPORT] [-Z TIMEOUT] [-M MARK] HOSTNAME DESCRIPTION mtr combines the functionality of the traceroute and ping programs in a single network diagnostic tool. As mtr starts, it investigates the network connection between the host mtr runs on and HOSTNAME by sending packets with purposely low TTLs. It continues to send packets with low TTL, noting the response time of the intervening routers. This allows mtr to print the response per- centage and response times of the internet route to HOSTNAME. A sudden increase in packet loss or response time is often an indication of a bad (or simply overloaded) link. The results are usually reported as round-trip-response times in mil- liseconds and the percentage of packet loss. OPTIONS -h, --help Print the summary of command line argument options. -v, --version Print the installed version of mtr. -4 Use IPv4 only. -6 Use IPv6 only. (IPV4 may be used for DNS lookups.) -F FILENAME, --filename FILENAME Reads the list of hostnames from the specified file. -r, --report This option puts mtr into report mode. When in this mode, mtr will run for the number of cycles specified by the -c option, and then print statistics and exit. This mode is useful for generating statistics about network quality. Note that each running instance of mtr generates a significant amount of network traffic. Using mtr to measure the quality of your network may result in decreased network performance. -w, --report-wide This option puts mtr into wide report mode. When in this mode, mtr will not cut hostnames in the report. -x, --xml Use this option to tell mtr to use the xml output format. This format is better suited for automated processing of the measure- ment results. -t, --curses Use this option to force mtr to use the curses based terminal interface (if available). In case the list of hops exceeds the height of your terminal, you can use the + and - keys to scroll up and down half a page. Ctrl-L clears spurious error messages that may overwrite other parts of the display. --displaymode MODE Use this option to select the initial display mode: 0 (default) selects statistics, 1 selects the stripchart without latency in- formation, and 2 selects the stripchart with latency informa- tion. -g, --gtk Use this option to force mtr to use the GTK+ based X11 window interface (if available). GTK+ must have been available on the system when mtr was built for this to work. See the GTK+ web page at <http://www.gtk.org/> for more information about GTK+. -l, --raw Use the raw output format. This format is better suited for archival of the measurement results. It could be parsed to be presented into any of the other display methods. Example of the raw output format: h 0 10.1.1.1 p 0 339 h 1 46.149.16.4 p 1 530 h 2 172.31.1.16 p 2 531 h 3 82.221.168.236 p 3 1523 h 5 195.130.211.8 p 5 1603 h 6 193.4.58.17 p 6 1127 h 7 193.4.58.17 d 7 www.isnic.is -C, --csv Use the Comma-Separated-Value (CSV) output format. (Note: The separator is actually a semi-colon ';'.) Example of the CSV output format: MTR.0.86+git:16e39fc0;1435562787;OK;nic.is;1;r-76520-PROD.greenqloud.internal;288 MTR.0.86+git:16e39fc0;1435562787;OK;nic.is;2;46.149.16.4;2086 MTR.0.86+git:16e39fc0;1435562787;OK;nic.is;3;172.31.1.16;600 MTR.0.86+git:16e39fc0;1435562787;OK;nic.is;4;82.221.168.236;1163 MTR.0.86+git:16e39fc0;1435562787;OK;nic.is;5;???;0 MTR.0.86+git:16e39fc0;1435562787;OK;nic.is;6;rix-k2-gw.isnic.is;1654 MTR.0.86+git:16e39fc0;1435562787;OK;nic.is;7;www.isnic.is;1036 -j, --json Use this option to tell mtr to use the JSON output format. This format is better suited for automated processing of the measure- ment results. Jansson library must have been available on the system when mtr was built for this to work. -p, --split Use this option to set mtr to spit out a format that is suitable for a split-user interface. -n, --no-dns Use this option to force mtr to display numeric IP numbers and not try to resolve the host names. -b, --show-ips Use this option to tell mtr to display both the host names and numeric IP numbers. In split mode this adds an extra field to the output. In report mode, there is usually too little space to add the IPs, and they will be truncated. Use the wide report (-w) mode to see the IPs in report mode. -o FIELDS, --order FIELDS Use this option to specify which fields to display and in which order. You may use one or more space characters to separate fields. Available fields: +---+---------------------+ | L | Loss ratio | +---+---------------------+ | D | Dropped packets | +---+---------------------+ | R | Received packets | +---+---------------------+ | S | Sent Packets | +---+---------------------+ | N | Newest RTT(ms) | +---+---------------------+ | B | Min/Best RTT(ms) | +---+---------------------+ | A | Average RTT(ms) | +---+---------------------+ | W | Max/Worst RTT(ms) | +---+---------------------+ | V | Standard Deviation | +---+---------------------+ | G | Geometric Mean | +---+---------------------+ | J | Current Jitter | +---+---------------------+ | M | Jitter Mean/Avg. | +---+---------------------+ | X | Worst Jitter | +---+---------------------+ | I | Interarrival Jitter | +---+---------------------+ Example: -o "LSD NBAW X" -y n, --ipinfo n Displays information about each IP hop. Valid values for n are: 0 Display AS number (equivalent to -z) 1 Display IP prefix 2 Display country code of the origin AS 3 Display RIR (ripencc, arin, ...) 4 Display the allocation date of the IP prefix It is possible to cycle between these fields at runtime (using the y key). -z, --aslookup Displays the Autonomous System (AS) number alongside each hop. Equivalent to --ipinfo 0. Example (columns to the right not shown for clarity): 1. AS??? r-76520-PROD.greenqloud.internal 2. AS51969 46.149.16.4 3. AS??? 172.31.1.16 4. AS30818 82.221.168.236 5. ??? 6. AS??? rix-k2-gw.isnic.is 7. AS1850 www.isnic.is --ipinfo_provider4 DOMAIN Provider for IPv4 AS lookups. Defaults to origin.asn.cymru.com. --ipinfo_provider6 DOMAIN Provider for IPv6 AS lookups. Defaults to ori- gin6.asn.cymru.com. -i SECONDS, --interval SECONDS Use this option to specify the positive number of seconds be- tween ICMP ECHO requests. The default value for this parameter is one second. The root user may choose values between zero and one. -c COUNT, --report-cycles COUNT Use this option to set the number of pings sent to determine both the machines on the network and the reliability of those machines. Each cycle lasts one second. -s PACKETSIZE, --psize PACKETSIZE This option sets the packet size used for probing. It is in bytes, inclusive IP and ICMP headers. If set to a negative number, every iteration will use a differ- ent, random packet size up to that number. -B NUM, --bitpattern NUM Specifies bit pattern to use in payload. Should be within range 0 - 255. If NUM is greater than 255, a random pattern is used. -G SECONDS, --gracetime SECONDS Use this option to specify the positive number of seconds to wait for responses after the final request. The default value is five seconds. -Q NUM, --tos NUM Specifies value for type of service field in IP header. Should be within range 0 - 255. -e, --mpls Use this option to tell mtr to display information from ICMP ex- tensions for MPLS (RFC 4950) that are encoded in the response packets. -I NAME, --interface NAME Use the network interface with a specific name for sending net- work probes. This can be useful when you have multiple network interfaces with routes to your destination, for example both wired Ethernet and WiFi, and wish to test a particular inter- face. -a ADDRESS, --address ADDRESS Use this option to bind the outgoing socket to ADDRESS, so that all packets will be sent with ADDRESS as source address. NOTE that this option doesn't apply to DNS requests (which could be and could not be what you want). -f NUM, --first-ttl NUM Specifies with what TTL to start. Defaults to 1. -m NUM, --max-ttl NUM Specifies the maximum number of hops (max time-to-live value) traceroute will probe. Default is 30. -U NUM, --max-unknown NUM Specifies the maximum unknown host. Default is 5. -E NUM, --max-display-path NUM Specifies the maximum number of ECMP paths to display. Default is 8. -u, --udp Use UDP datagrams instead of ICMP ECHO. -T, --tcp Use TCP SYN packets instead of ICMP ECHO. PACKETSIZE is ig- nored, since SYN packets can not contain data. -S, --sctp Use Stream Control Transmission Protocol packets instead of ICMP ECHO. -P PORT, --port PORT The target port number for TCP/SCTP/UDP traces. -L LOCALPORT, --localport LOCALPORT The source port number for UDP traces. -Z SECONDS, --timeout SECONDS The number of seconds to keep probe sockets open before giving up on the connection. Using large values for this, especially combined with a short interval, will use up a lot of file de- scriptors. -M MARK, --mark MARK Set the mark for each packet sent through this socket similar to the netfilter MARK target but socket-based. MARK is a 32-bit unsigned integer. See socket(7) for full description of this socket option. ENVIRONMENT mtr recognizes a few environment variables. MTR_OPTIONS This environment variable allows one to specify options, as if they were passed on the command line. It is parsed before read- ing the actual command line options, so that options specified in MTR_OPTIONS are overridden by command-line options. Example: MTR_OPTIONS="-4 -c 1" mtr -6 localhost would send one probe (because of -c 1) towards ::1 (because of -6, which overrides the -4 passed in MTR_OPTIONS). MTR_PACKET A path to the mtr-packet executable, to be used for sending and receiving network probes. If MTR_PACKET is unset, the PATH will be used to search for an mtr-packet executable. DISPLAY Specifies an X11 server for the GTK+ frontend. INTERACTIVE CONTROL mtr can be controlled while it is running with the following keys: ?|h help p pause (SPACE to resume) d switching display mode e toggle MPLS information on/off n toggle DNS on/off r reset all counters o str set the columns to display, default str='LRS N BAWV' j toggle latency(LS NABWV)/jitter(DR AGJMXI) stats c <n> report cycle n, default n=infinite i <n> set the ping interval to n seconds, default n=1 f <n> set the initial time-to-live(ttl), default n=1 m <n> set the max time-to-live, default n= # of hops s <n> set the packet size to n or random(n<0) b <c> set ping bit pattern to c(0..255) or random(c<0) Q <t> set ping packet's TOS to t u switch between ICMP ECHO and UDP datagrams y switching IP info z toggle ASN info on/off q exit BUGS Some modern routers give a lower priority to ICMP ECHO packets than to other network traffic. Consequently, the reliability of these routers reported by mtr will be significantly lower than the actual reliability of these routers. CONTACT INFORMATION For the latest version, see the mtr web page at <http://www.bitwizard. nl/mtr/> For patches, bug reports, or feature requests, please open an issue on GitHub at: <https://github.com/traviscross/mtr>. SEE ALSO mtr-packet(8), traceroute(8), ping(8), socket(7), TCP/IP Illustrated (Stevens, ISBN 0201633469). mtr 0.96 MTR(8)
NAME | SYNOPSIS | DESCRIPTION | OPTIONS | ENVIRONMENT | INTERACTIVE CONTROL | BUGS | CONTACT INFORMATION | SEE ALSO
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=mtr&manpath=FreeBSD+15.0-RELEASE+and+Ports>