FreeBSD Manual Pages
NG_ETHER(4) BSD Kernel Interfaces Manual NG_ETHER(4) NAME ng_ether -- Ethernet netgraph node type SYNOPSIS #include <netgraph/ng_ether.h> DESCRIPTION The ng_ether netgraph node type allows Ethernet interfaces to interact with the netgraph(4) networking subsystem. Once the ng_ether module is loaded in the kernel, a node is automatically created for each Ethernet interface in the system. Each node will attempt to name itself with the same name as the associated interface. All ng_ether nodes are persistent for as long as the interface itself exists. Three hooks are supported: lower, upper, and orphans. The hook name divert may be used as an alias for lower, and is provided for backward compatibility. In reality the two names represent the same hook. The lower hook is a connection to the raw Ethernet device. When con- nected, all incoming packets are diverted out this hook. Writing to this hook results in a raw Ethernet frame being transmitted by the device. Normal outgoing packets are not affected by lower being connected. The upper hook is a connection to the upper protocol layers. When con- nected, all outgoing packets are diverted out this hook. Writing to this hook results in a raw Ethernet frame being received by the kernel just as if it had come in over the wire. Normal incoming packets are not af- fected by upper being connected. The orphans hook is equivalent to lower, except that only unrecognized packets (that would otherwise be discarded) are written to the hook, and normal incoming traffic is unaffected. At most one of orphans and lower may be connected at any time. In all cases, frames are raw Ethernet frames with the standard 14 byte Ethernet header (but no checksum). When no hooks are connected, upper and lower are in effect connected to- gether, so that packets flow normally upwards and downwards. HOOKS This node type supports the following hooks: lower Connection to the lower device link layer. upper Connection to the upper protocol layers. orphans Like lower, but only receives unrecognized packets. CONTROL MESSAGES This node type supports the generic control messages, plus the following: NGM_ETHER_GET_IFNAME Returns the name of the associated interface as a NUL-terminated ASCII string. Normally this is the same as the name of the node. NGM_ETHER_GET_IFINDEX Returns the global index of the associated interface as a 32 bit in- teger. NGM_ETHER_GET_ENADDR Returns the device's unique six byte Ethernet address. NGM_ETHER_SET_ENADDR Sets the device's unique six byte Ethernet address. This control message is equivalent to using the SIOCSIFLLADDR ioctl(2) system call. NGM_ETHER_SET_PROMISC Enable or disable promiscuous mode. This message includes a single 32 bit integer flag that enables or disables promiscuous mode on the interface. NGM_ETHER_GET_PROMISC Get the current value of the node's promiscuous flag. The returned value is always either one or zero. Note that this flag reflects the node's own promiscuous setting and does not necessarily reflect the promiscuous state of the actual interface, which can be affected by other means (e.g., bpf(4)). NGM_ETHER_SET_AUTOSRC Sets the automatic source address override flag. This message in- cludes a single 32 bit integer flag that causes all outgoing packets to have their source Ethernet address field overwritten with the de- vice's unique Ethernet address. If this flag is set to zero, the source address in outgoing packets is not modified. The default setting for this flag is enabled. NGM_ETHER_GET_AUTOSRC Get the current value of the node's source address override flag. The returned value is always either one or zero. SHUTDOWN This node is persistent for as long as the interface exists. Upon re- ceipt of a NGM_SHUTDOWN control message, all hooks are disconnected, pro- miscuous mode is disabled, and the source address override flag is reen- abled, but the node is not removed. If the interface itself is detached (e.g., because of PCCARD removal), the node disappears as well. EXAMPLES This command dumps all unrecognized packets received by the fxp0 inter- face to standard output decoded in hex and ASCII: nghook -a fxp0: orphans This command sends the contents of foo.pkt out the interface fxp0: cat foo.pkt | nghook fxp0: orphans These commands insert an ng_tee(4) node between the lower and upper pro- tocol layers, which can be used for tracing packet flow, statistics, etc.: ngctl mkpeer fxp0: tee lower right ngctl connect fxp0: lower upper left BUGS The automatic KLD module loading mechanism that works for most other net- graph node types does not work for the ng_ether node type, because ng_ether nodes are not created on demand; instead, they are created when Ethernet interfaces are attached or when the KLD is first loaded. There- fore, if the KLD is not statically compiled into the kernel, it is neces- sary to load the KLD manually in order to bring the ng_ether nodes into existence. SEE ALSO arp(4), netgraph(4), netintro(4), ifconfig(8), ngctl(8), nghook(8) AUTHORS Julian Elischer <julian@FreeBSD.org> Archie Cobbs <archie@FreeBSD.org> BSD June 26, 2000 BSD
NAME | SYNOPSIS | DESCRIPTION | HOOKS | CONTROL MESSAGES | SHUTDOWN | EXAMPLES | BUGS | SEE ALSO | AUTHORS
Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=ng_ether&sektion=4&manpath=FreeBSD+5.2.1-RELEASE>