FreeBSD Manual Pages
PFCTL(8) BSD System Manager's Manual PFCTL(8) NAME pfctl -- control the packet filter (PF) and network address translation (NAT) device SYNOPSIS pfctl [-AdeghmNnOqRrvz] [-a anchor] [-D macro= value] [-F modifier] [-f file] [-i interface] [-K host | network] [-k host | network] [-o [level]] [-p device] [-s modifier] [-t table -T command [address ...]] [-x level] DESCRIPTION The pfctl utility communicates with the packet filter device using the ioctl interface described in pf(4). It allows ruleset and parameter con- figuration and retrieval of status information from the packet filter. Packet filtering restricts the types of packets that pass through network interfaces entering or leaving the host based on filter rules as de- scribed in pf.conf(5). The packet filter can also replace addresses and ports of packets. Replacing source addresses and ports of outgoing pack- ets is called NAT (Network Address Translation) and is used to connect an internal network (usually reserved address space) to an external one (the Internet) by making all connections to external hosts appear to come from the gateway. Replacing destination addresses and ports of incoming pack- ets is used to redirect connections to different hosts and/or ports. A combination of both translations, bidirectional NAT, is also supported. Translation rules are described in pf.conf(5). When the variable pf is set to YES in rc.conf.local(5), the rule file specified with the variable pf_rules is loaded automatically by the rc(8) scripts and the packet filter is enabled. The packet filter does not itself forward packets between interfaces. Forwarding can be enabled by setting the sysctl(8) variables net.inet.ip.forwarding and/or net.inet6.ip6.forwarding to 1. Set them permanently in sysctl.conf(5). The pfctl utility provides several commands. The options are as follows: -A Load only the queue rules present in the rule file. Other rules and options are ignored. -a anchor Apply flags -f, -F, and -s only to the rules in the specified anchor. In addition to the main ruleset, pfctl can load and ma- nipulate additional rulesets by name, called anchors. The main ruleset is the default anchor. Anchors are referenced by name and may be nested, with the vari- ous components of the anchor path separated by `/' characters, similar to how file system hierarchies are laid out. The last component of the anchor path is where ruleset operations are per- formed. Evaluation of anchor rules from the main ruleset is described in pf.conf(5). For example, the following will show all filter rules (see the -s flag below) inside the anchor "authpf/smith(1234)", which would have been created for user "smith" by authpf(8), PID 1234: # pfctl -a "authpf/smith(1234)" -s rules Private tables can also be put inside anchors, either by having table statements in the pf.conf(5) file that is loaded in the an- chor, or by using regular table commands, as in: # pfctl -a foo/bar -t mytable -T add 1.2.3.4 5.6.7.8 When a rule referring to a table is loaded in an anchor, the rule will use the private table if one is defined, and then fall back to the table defined in the main ruleset, if there is one. This is similar to C rules for variable scope. It is possible to cre- ate distinct tables with the same name in the global ruleset and in an anchor, but this is often bad design and a warning will be issued in that case. By default, recursive inline printing of anchors applies only to unnamed anchors specified inline in the ruleset. If the anchor name is terminated with a `*' character, the -s flag will recur- sively print all anchors in a brace delimited block. For example the following will print the "authpf" ruleset recursively: # pfctl -a 'authpf/*' -sr To print the main ruleset recursively, specify only `*' as the anchor name: # pfctl -a '*' -sr -D macro=value Define macro to be set to value on the command line. Overrides the definition of macro in the ruleset. -d Disable the packet filter. -e Enable the packet filter. -F modifier Flush the filter parameters specified by modifier (may be abbre- viated): -F nat Flush the NAT rules. -F queue Flush the queue rules. -F rules Flush the filter rules. -F state Flush the state table (NAT and filter). -F Sources Flush the source tracking table. -F info Flush the filter information (statistics that are not bound to rules). -F Tables Flush the tables. -F osfp Flush the passive operating system fingerprints. -F all Flush all of the above. -f file Load the rules contained in file. This file may contain macros, tables, options, and normalization, queueing, translation, and filtering rules. With the exception of macros and tables, the statements must appear in that order. -g Include output helpful for debugging. -h Help. -i interface Restrict the operation to the given interface. -K host | network Kill all of the source tracking entries originating from the specified host or network. A second -K host or -K network option may be specified, which will kill all the source tracking entries from the first host/network to the second. -k host | network Kill all of the state entries originating from the specified host or network. A second -k host or -k network option may be speci- fied, which will kill all the state entries from the first host/network to the second. For example, to kill all of the state entries originating from "host": # pfctl -k host To kill all of the state entries from "host1" to "host2": # pfctl -k host1 -k host2 To kill all states originating from 192.168.1.0/24 to 172.16.0.0/16: # pfctl -k 192.168.1.0/24 -k 172.16.0.0/16 A network prefix length of 0 can be used as a wildcard. To kill all states with the target "host2": # pfctl -k 0.0.0.0/0 -k host2 -m Merge in explicitly given options without resetting those which are omitted. Allows single options to be modified without dis- turbing the others: # echo "set loginterface fxp0" | pfctl -mf - -N Load only the NAT rules present in the rule file. Other rules and options are ignored. -n Do not actually load rules, just parse them. -O Load only the options present in the rule file. Other rules and options are ignored. -o [level] Control the ruleset optimizer. The ruleset optimizer attempts to improve rulesets by removing rule duplication and making better use of rule ordering. -o none Disable the ruleset optimizer. -o basic Enable basic ruleset optimizations. -o profile Enable basic ruleset optimizations with profiling. basic optimization does does four things: 1. remove duplicate rules 2. remove rules that are a subset of another rule 3. combine multiple rules into a table when advantageous 4. re-order the rules to improve evaluation performance If profile is specified, the currently loaded ruleset will be ex- amined as a feedback profile to tailor the optimization of the quick rules to the actual network behavior. It is important to note that the ruleset optimizer will modify the ruleset to improve performance. A side effect of the ruleset modification is that per-rule accounting statistics will have different meanings than before. If per-rule accounting is impor- tant for billing purposes or whatnot, either the ruleset opti- mizer should not be used or a label field should be added to all of the accounting rules to act as optimization barriers. To retain compatibility with previous behaviour, a single -o without any options will enable basic optimizations, and a second -o will enable profiling. -p device Use the device file device instead of the default /dev/pf. -q Only print errors and warnings. -R Load only the filter rules present in the rule file. Other rules and options are ignored. -r Perform reverse DNS lookups on states when displaying them. -s modifier Show the filter parameters specified by modifier (may be abbrevi- ated): -s nat Show the currently loaded NAT rules. -s queue Show the currently loaded queue rules. When used together with -v, per-queue statistics are also shown. When used together with -v -v, pfctl will loop and show updated queue statistics every five seconds, including measured bandwidth and packets per second. -s rules Show the currently loaded filter rules. When used together with -v, the per-rule statistics (number of evaluations, packets and bytes) are also shown. Note that the "skip step" optimization done auto- matically by the kernel will skip evaluation of rules where possible. Packets passed statefully are counted in the rule that created the state (even though the rule isn't evaluated more than once for the entire connection). -s Anchors Show the currently loaded anchors directly at- tached to the main ruleset. If -a anchor is spec- ified as well, the anchors loaded directly below the given anchor are shown instead. If -v is specified, all anchors attached under the target anchor will be displayed recursively. -s state Show the contents of the state table. -s Sources Show the contents of the source tracking table. -s info Show filter information (statistics and counters). When used together with -v, source tracking sta- tistics are also shown. -s labels Show per-rule statistics (label, evaluations, packets total, bytes total, packets in, bytes in, packets out, bytes out) of filter rules with la- bels, useful for accounting. -s timeouts Show the current global timeouts. -s memory Show the current pool memory hard limits. -s Tables Show the list of tables. -s osfp Show the list of operating system fingerprints. -s Interfaces Show the list of interfaces and interface drivers available to PF. When used together with -v, it additionally lists which interfaces have skip rules activated. When used together with -vv, in- terface statistics are also shown. -i can be used to select an interface or a group of interfaces. -s all Show all of the above, except for the lists of in- terfaces and operating system fingerprints. -T command [address ...] Specify the command (may be abbreviated) to apply to the table. Commands include: -T kill Kill a table. -T flush Flush all addresses of a table. -T add Add one or more addresses in a table. Automati- cally create a nonexisting table. -T delete Delete one or more addresses from a table. -T expire number Delete addresses which had their statistics cleared more than number seconds ago. For entries which have never had their statistics cleared, number refers to the time they were added to the table. -T replace Replace the addresses of the table. Automatically create a nonexisting table. -T show Show the content (addresses) of a table. -T test Test if the given addresses match a table. -T zero Clear all the statistics of a table. -T load Load only the table definitions from pf.conf(5). This is used in conjunction with the -f flag, as in: # pfctl -Tl -f pf.conf For the add, delete, replace, and test commands, the list of ad- dresses can be specified either directly on the command line and/or in an unformatted text file, using the -f flag. Comments starting with a `#' are allowed in the text file. With these commands, the -v flag can also be used once or twice, in which case pfctl will print the detailed result of the operation for each individual address, prefixed by one of the following let- ters: A The address/network has been added. C The address/network has been changed (negated). D The address/network has been deleted. M The address matches (test operation only). X The address/network is duplicated and therefore ignored. Y The address/network cannot be added/deleted due to conflict- ing `!' attributes. Z The address/network has been cleared (statistics). Each table maintains a set of counters that can be retrieved us- ing the -v flag of pfctl. For example, the following commands define a wide open firewall which will keep track of packets go- ing to or coming from the OpenBSD FTP server. The following com- mands configure the firewall and send 10 pings to the FTP server: # printf "table <test> { ftp.openbsd.org }\n \ pass out to <test>\n" | pfctl -f- # ping -qc10 ftp.openbsd.org We can now use the table show command to output, for each address and packet direction, the number of packets and bytes that are being passed or blocked by rules referencing the table. The time at which the current accounting started is also shown with the "Cleared" line. # pfctl -t test -vTshow 129.128.5.191 Cleared: Thu Feb 13 18:55:18 2003 In/Block: [ Packets: 0 Bytes: 0 ] In/Pass: [ Packets: 10 Bytes: 840 ] Out/Block: [ Packets: 0 Bytes: 0 ] Out/Pass: [ Packets: 10 Bytes: 840 ] Similarly, it is possible to view global information about the tables by using the -v modifier twice and the -s Tables command. This will display the number of addresses on each table, the num- ber of rules which reference the table, and the global packet statistics for the whole table: # pfctl -vvsTables --a-r- test Addresses: 1 Cleared: Thu Feb 13 18:55:18 2003 References: [ Anchors: 0 Rules: 1 ] Evaluations: [ NoMatch: 3496 Match: 1 ] In/Block: [ Packets: 0 Bytes: 0 ] In/Pass: [ Packets: 10 Bytes: 840 ] In/XPass: [ Packets: 0 Bytes: 0 ] Out/Block: [ Packets: 0 Bytes: 0 ] Out/Pass: [ Packets: 10 Bytes: 840 ] Out/XPass: [ Packets: 0 Bytes: 0 ] As we can see here, only one packet - the initial ping request - matched the table, but all packets passing as the result of the state are correctly accounted for. Reloading the table(s) or ruleset will not affect packet accounting in any way. The two "XPass" counters are incremented instead of the "Pass" counters when a "stateful" packet is passed but doesn't match the table anymore. This will happen in our example if someone flushes the table while the ping(8) command is running. When used with a single -v, pfctl will only display the first line containing the table flags and name. The flags are defined as follows: c For constant tables, which cannot be altered outside pf.conf(5). p For persistent tables, which don't get automatically killed when no rules refer to them. a For tables which are part of the active tableset. Tables without this flag do not really exist, cannot contain ad- dresses, and are only listed if the -g flag is given. i For tables which are part of the inactive tableset. This flag can only be witnessed briefly during the loading of pf.conf(5). r For tables which are referenced (used) by rules. h This flag is set when a table in the main ruleset is hidden by one or more tables of the same name from anchors attached below it. -t table Specify the name of the table. -v Produce more verbose output. A second use of -v will produce even more verbose output including ruleset warnings. See the previous section for its effect on table commands. -x level Set the debug level (may be abbreviated) to one of the following: -x none Don't generate debug messages. -x urgent Generate debug messages only for serious errors. -x misc Generate debug messages for various errors. -x loud Generate debug messages for common conditions. -z Clear per-rule statistics. FILES /etc/pf.conf Packet filter rules file. /etc/pf.os Passive operating system fingerprint database. SEE ALSO pf(4), pf.conf(5), pf.os(5), rc.conf(5), sysctl.conf(5), authpf(8), ftp-proxy(8), rc(8), sysctl(8) HISTORY The pfctl program and the pf(4) filter mechanism first appeared in OpenBSD 3.0. BSD November 20, 2002 BSD
NAME | SYNOPSIS | DESCRIPTION | FILES | SEE ALSO | HISTORY
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=pfctl&sektion=8&manpath=FreeBSD+7.1-RELEASE>