FreeBSD Manual Pages
PPP(8) BSD System Manager's Manual PPP(8) NAME ppp -- Point to Point Protocol (a.k.a. user-ppp) SYNOPSIS ppp [-mode] [-nat] [-quiet] [-unitN] [system ...] DESCRIPTION This is a user process PPP software package. Normally, PPP is imple- mented as a part of the kernel (e.g., as managed by pppd(8)) and it's thus somewhat hard to debug and/or modify its behaviour. However, in this implementation PPP is done as a user process with the help of the tunnel device driver (tun). The -nat flag does the equivalent of a "nat enable yes", enabling ppp's network address translation features. This allows ppp to act as a NAT or masquerading engine for all machines on an internal LAN. Refer to libalias(3) for details on the technical side of the NAT engine. Refer to the NETWORK ADDRESS TRANSLATION (PACKET ALIASING) section of this man- ual page for details on how to configure NAT in ppp. The -quiet flag tells ppp to be silent at startup rather than displaying the mode and interface to standard output. The -unit flag tells ppp to only attempt to open /dev/tunN. Normally, ppp will start with a value of 0 for N, and keep trying to open a tunnel device by incrementing the value of N by one each time until it succeeds. If it fails three times in a row because the device file is missing, it gives up. The following modes are understood by ppp: -auto ppp opens the tun interface, configures it then goes into the background. The link isn't brought up until outgoing data is de- tected on the tun interface at which point ppp attempts to bring up the link. Packets received (including the first one) while ppp is trying to bring the link up will remain queued for a de- fault of 2 minutes. See the "set choked" command below. In -auto mode, at least one "system" must be given on the command line (see below) and a "set ifaddr" must be done in the system profile that specifies a peer IP address to use when configuring the interface. Something like "10.0.0.1/0" is usually appropri- ate. See the "pmdemand" system in /usr/share/examples/ppp/ppp.conf.sample for an example. -background Here, ppp attempts to establish a connection with the peer imme- diately. If it succeeds, ppp goes into the background and the parent process returns an exit code of 0. If it fails, ppp exits with a non-zero result. -foreground In foreground mode, ppp attempts to establish a connection with the peer immediately, but never becomes a daemon. The link is created in background mode. This is useful if you wish to con- trol ppp's invocation from another process. -direct This is used for receiving incoming connections. ppp ignores the "set device" line and uses descriptor 0 as the link. If callback is configured, ppp will use the "set device" informa- tion when dialing back. -dedicated This option is designed for machines connected with a dedicated wire. ppp will always keep the device open and will never use any configured chat scripts. -ddial This mode is equivalent to -auto mode except that ppp will bring the link back up any time it's dropped for any reason. -interactive This is a no-op, and gives the same behaviour as if none of the above modes have been specified. ppp loads any sections speci- fied on the command line then provides an interactive prompt. One or more configuration entries or systems (as specified in /etc/ppp/ppp.conf) may also be specified on the command line. ppp will read the "default" system from /etc/ppp/ppp.conf at startup, followed by each of the systems specified on the command line. Major Features Provides an interactive user interface. Using its command mode, the user can easily enter commands to establish the connection with the remote end, check the status of connection and close the connection. All func- tions can also be optionally password protected for security. Supports both manual and automatic dialing. Interactive mode has a "term" command which enables you to talk to the device directly. When you are connected to the remote peer and it starts to talk PPP, ppp de- tects it and switches to packet mode automatically. Once you have deter- mined the proper sequence for connecting with the remote host, you can write a chat script to define the necessary dialing and login procedure for later convenience. Supports on-demand dialup capability. By using -auto mode, ppp will act as a daemon and wait for a packet to be sent over the PPP link. When this happens, the daemon automatically dials and establishes the connec- tion. In almost the same manner -ddial mode (direct-dial mode) also au- tomatically dials and establishes the connection. However, it differs in that it will dial the remote site any time it detects the link is down, even if there are no packets to be sent. This mode is useful for full- time connections where we worry less about line charges and more about being connected full time. A third -dedicated mode is also available. This mode is targeted at a dedicated link between two machines. ppp will never voluntarily quit from dedicated mode - you must send it the "quit all" command via its diagnostic socket. A SIGHUP will force an LCP rene- gotiation, and a SIGTERM will force it to exit. Supports client callback. ppp can use either the standard LCP callback protocol or the Microsoft CallBack Control Protocol (ftp://ftp.micro- soft.com/developr/rfc/cbcp.txt). Supports NAT or packet aliasing. Packet aliasing (a.k.a. IP masquerad- ing) allows computers on a private, unregistered network to access the Internet. The PPP host acts as a masquerading gateway. IP addresses as well as TCP and UDP port numbers are NAT'd for outgoing packets and de- NAT'd for returning packets. Supports background PPP connections. In background mode, if ppp success- fully establishes the connection, it will become a daemon. Otherwise, it will exit with an error. This allows the setup of scripts that wish to execute certain commands only if the connection is successfully estab- lished. Supports server-side PPP connections. In direct mode, ppp acts as server which accepts incoming PPP connections on stdin/stdout. Supports PAP and CHAP (rfc 1994, 2433 and 2759) authentication. With PAP or CHAP, it is possible to skip the Unix style login(1) procedure, and use the PPP protocol for authentication instead. If the peer requests Microsoft CHAP authentication and ppp is compiled with DES support, an appropriate MD4/DES response will be made. Supports RADIUS (rfc 2138 & 2548) authentication. An extension to PAP and CHAP, Remote Access Dial In User Service allows authentication infor- mation to be stored in a central or distributed database along with vari- ous per-user framed connection characteristics. If libradius(3) is available at compile time, ppp will use it to make RADIUS requests when configured to do so. Supports Proxy Arp. ppp can be configured to make one or more proxy arp entries on behalf of the peer. This allows routing from the peer to the LAN without configuring each machine on that LAN. Supports packet filtering. User can define four kinds of filters: the in filter for incoming packets, the out filter for outgoing packets, the dial filter to define a dialing trigger packet and the alive filter for keeping a connection alive with the trigger packet. Tunnel driver supports bpf. The user can use tcpdump(1) to check the packet flow over the PPP link. Supports PPP over TCP and PPP over UDP. If a device name is specified as host:port[/tcp|udp], ppp will open a TCP or UDP connection for transport- ing data rather than using a conventional serial device. UDP connections force ppp into synchronous mode. Supports PPP over ISDN. If ppp is given a raw B-channel i4b device to open as a link, it's able to talk to the isdnd(8) daemon to establish an ISDN connection. Supports PPP over Ethernet (rfc 2516). If ppp is given a device specifi- cation of the format PPPoE:iface[:provider] and if netgraph(4) is avail- able, ppp will attempt talk PPP over Ethernet to provider using the iface network interface. On systems that do not support netgraph(4), an external program such as pppoe(8) may be used. Supports IETF draft Predictor-1 (rfc 1978) and DEFLATE (rfc 1979) compression. ppp supports not only VJ-compression but also Predictor-1 and DEFLATE compression. Normally, a modem has built-in compression (e.g., v42.bis) and the system may receive higher data rates from it as a result of such compression. While this is generally a good thing in most other situations, this higher speed data imposes a penalty on the system by increasing the number of serial interrupts the system has to process in talking to the modem and also increases latency. Unlike VJ-compres- sion, Predictor-1 and DEFLATE compression pre-compresses all network traffic flowing through the link, thus reducing overheads to a minimum. Supports Microsoft's IPCP extensions (rfc 1877). Name Server Addresses and NetBIOS Name Server Addresses can be negotiated with clients using the Microsoft PPP stack (i.e., Win95, WinNT) Supports Multi-link PPP (rfc 1990) It is possible to configure ppp to open more than one physical connection to the peer, combining the band- width of all links for better throughput. Supports MPPE (draft-ietf-pppext-mppe) MPPE is Microsoft Point to Point Encryption scheme. It is possible to configure ppp to participate in Mi- crosoft's Windows VPN. For now, ppp can only get encryption keys from CHAP 81 authentication. ppp must be compiled with DES for MPPE to oper- ate. Supports IPV6CP (rfc 2023). An IPv6 connection can be made in addition to or instead of the normal IPv4 connection. PERMISSIONS ppp is installed as user root and group network, with permissions 04554. By default, ppp will not run if the invoking user id is not zero. This may be overridden by using the "allow users" command in /etc/ppp/ppp.conf. When running as a normal user, ppp switches to user id 0 in order to alter the system routing table, set up system lock files and read the ppp configuration files. All external commands (executed via the "shell" or "!bg" commands) are executed as the user id that in- voked ppp. Refer to the `ID0' logging facility if you're interested in what exactly is done as user id zero. GETTING STARTED When you first run ppp you may need to deal with some initial configura- tion details. o Your kernel must include a tunnel device (the GENERIC kernel includes one by default). If it doesn't, or if you require more than one tun interface, you'll need to rebuild your kernel with the following line in your kernel configuration file: pseudo-device tun N where N is the maximum number of PPP connections you wish to support. o Check your /dev directory for the tunnel device entries /dev/tunN, where `N' represents the number of the tun device, starting at zero. If they don't exist, you can create them by running "sh ./MAKEDEV tunN". This will create tun devices 0 through N. o Make sure that your system has a group named "network" in the /etc/group file and that the group contains the names of all users expected to use ppp. Refer to the group(5) manual page for details. Each of these users must also be given access using the "allow users" command in /etc/ppp/ppp.conf. o Create a log file. ppp uses syslog(3) to log information. A common log file name is /var/log/ppp.log. To make output go to this file, put the following lines in the /etc/syslog.conf file: !ppp *.*<TAB>/var/log/ppp.log It is possible to have more than one PPP log file by creating a link to the ppp executable: # cd /usr/sbin # ln ppp ppp0 and using !ppp0 *.*<TAB>/var/log/ppp0.log in /etc/syslog.conf. Don't forget to send a HUP signal to syslogd(8) after altering /etc/syslog.conf. o Although not strictly relevant to ppp's operation, you should config- ure your resolver so that it works correctly. This can be done by configuring a local DNS (using named(8)) or by adding the correct `nameserver' lines to the file /etc/resolv.conf. Refer to the resolv.conf(5) manual page for details. Alternatively, if the peer supports it, ppp can be configured to ask the peer for the nameserver address(es) and to update /etc/resolv.conf automatically. Refer to the "enable dns" and "resolv" commands below for details. MANUAL DIALING In the following examples, we assume that your machine name is awfulhak. when you invoke ppp (see PERMISSIONS above) with no arguments, you are presented with a prompt: ppp ON awfulhak> The `ON' part of your prompt should always be in upper case. If it is in lower case, it means that you must supply a password using the "passwd" command. This only ever happens if you connect to a running version of ppp and have not authenticated yourself using the correct password. You can start by specifying the device name and speed: ppp ON awfulhak> set device /dev/cuaa0 ppp ON awfulhak> set speed 38400 Normally, hardware flow control (CTS/RTS) is used. However, under cer- tain circumstances (as may happen when you are connected directly to cer- tain PPP-capable terminal servers), this may result in ppp hanging as soon as it tries to write data to your communications link as it is wait- ing for the CTS (clear to send) signal - which will never come. Thus, if you have a direct line and can't seem to make a connection, try turning CTS/RTS off with "set ctsrts off". If you need to do this, check the "set accmap" description below too - you'll probably need to "set accmap 000a0000". Usually, parity is set to "none", and this is ppp's default. Parity is a rather archaic error checking mechanism that is no longer used because modern modems do their own error checking, and most link-layer protocols (that's what ppp is) use much more reliable checking mechanisms. Parity has a relatively huge overhead (a 12.5% increase in traffic) and as a re- sult, it is always disabled (set to "none") when PPP is opened. However, some ISPs (Internet Service Providers) may use specific parity settings at connection time (before PPP is opened). Notably, Compuserve insist on even parity when logging in: ppp ON awfulhak> set parity even You can now see what your current device settings look like: ppp ON awfulhak> show physical Name: deflink State: closed Device: N/A Link Type: interactive Connect Count: 0 Queued Packets: 0 Phone Number: N/A Defaults: Device List: /dev/cuaa0 Characteristics: 38400bps, cs8, even parity, CTS/RTS on Connect time: 0 secs 0 octets in, 0 octets out Overall 0 bytes/sec ppp ON awfulhak> The term command can now be used to talk directly to the device: ppp ON awfulhak> term at OK atdt123456 CONNECT login: myispusername Password: myisppassword Protocol: ppp When the peer starts to talk in PPP, ppp detects this automatically and returns to command mode. ppp ON awfulhak> # No link has been established Ppp ON awfulhak> # We've connected & finished LCP PPp ON awfulhak> # We've authenticated PPP ON awfulhak> # We've agreed IP numbers If it does not, it's probable that the peer is waiting for your end to start negotiating. To force ppp to start sending PPP configuration pack- ets to the peer, use the "~p" command to drop out of terminal mode and enter packet mode. If you never even receive a login prompt, it is quite likely that the peer wants to use PAP or CHAP authentication instead of using Unix-style login/password authentication. To set things up properly, drop back to the prompt and set your authentication name and key, then reconnect: ~. ppp ON awfulhak> set authname myispusername ppp ON awfulhak> set authkey myisppassword ppp ON awfulhak> term at OK atdt123456 CONNECT You may need to tell ppp to initiate negotiations with the peer here too: ~p ppp ON awfulhak> # No link has been established Ppp ON awfulhak> # We've connected & finished LCP PPp ON awfulhak> # We've authenticated PPP ON awfulhak> # We've agreed IP numbers You are now connected! Note that `PPP' in the prompt has changed to cap- ital letters to indicate that you have a peer connection. If only some of the three Ps go uppercase, wait until either everything is uppercase or lowercase. If they revert to lowercase, it means that ppp couldn't successfully negotiate with the peer. A good first step for trou- bleshooting at this point would be to ppp ON awfulhak> set log local phase lcp ipcp and try again. Refer to the "set log" command description below for fur- ther details. If things fail at this point, it is quite important that you turn logging on and try again. It is also important that you note any prompt changes and report them to anyone trying to help you. When the link is established, the show command can be used to see how things are going: PPP ON awfulhak> show physical * Modem related information is shown here * PPP ON awfulhak> show ccp * CCP (compression) related information is shown here * PPP ON awfulhak> show lcp * LCP (line control) related information is shown here * PPP ON awfulhak> show ipcp * IPCP (IP) related information is shown here * PPP ON awfulhak> show ipv6cp * IPV6CP (IPv6) related information is shown here * PPP ON awfulhak> show link * Link (high level) related information is shown here * PPP ON awfulhak> show bundle * Logical (high level) connection related information is shown here * At this point, your machine has a host route to the peer. This means that you can only make a connection with the host on the other side of the link. If you want to add a default route entry (telling your machine to send all packets without another routing entry to the other side of the PPP link), enter the following command: PPP ON awfulhak> add default HISADDR The string `HISADDR' represents the IP address of the connected peer. If the "add" command fails due to an existing route, you can overwrite the existing route using PPP ON awfulhak> add! default HISADDR This command can also be executed before actually making the connection. If a new IP address is negotiated at connection time, ppp will update your default route accordingly. You can now use your network applications (ping, telnet, ftp etc.) in other windows or terminals on your machine. If you wish to reuse the current terminal, you can put ppp into the background using your standard shell suspend and background commands (usually "^Z" followed by "bg"). Refer to the PPP COMMAND LIST section for details on all available com- mands. AUTOMATIC DIALING To use automatic dialing, you must prepare some Dial and Login chat scripts. See the example definitions in /usr/share/examples/ppp/ppp.conf.sample (the format of /etc/ppp/ppp.conf is pretty simple). Each line contains one comment, inclusion, label or command: o A line starting with a ("#") character is treated as a comment line. Leading whitespace are ignored when identifying comment lines. o An inclusion is a line beginning with the word `!include'. It must have one argument - the file to include. You may wish to "!include ~/.ppp.conf" for compatibility with older versions of ppp. o A label name starts in the first column and is followed by a colon (":"). o A command line must contain a space or tab in the first column. The /etc/ppp/ppp.conf file should consist of at least a "default" sec- tion. This section is always executed. It should also contain one or more sections, named according to their purpose, for example, "MyISP" would represent your ISP, and "ppp-in" would represent an incoming ppp configuration. You can now specify the destination label name when you invoke ppp. Commands associated with the "default" label are executed, followed by those associated with the destination label provided. When ppp is started with no arguments, the "default" section is still exe- cuted. The load command can be used to manually load a section from the /etc/ppp/ppp.conf file: ppp ON awfulhak> load MyISP Note, no action is taken by ppp after a section is loaded, whether it's the result of passing a label on the command line or using the "load" command. Only the commands specified for that label in the configuration file are executed. However, when invoking ppp with the -background, -ddial, or -dedicated switches, the link mode tells ppp to establish a connection. Refer to the "set mode" command below for further details. Once the connection is made, the `ppp' portion of the prompt will change to `PPP': # ppp MyISP ... ppp ON awfulhak> dial Ppp ON awfulhak> PPp ON awfulhak> PPP ON awfulhak> The Ppp prompt indicates that ppp has entered the authentication phase. The PPp prompt indicates that ppp has entered the network phase. The PPP prompt indicates that ppp has successfully negotiated a network layer protocol and is in a usable state. If the /etc/ppp/ppp.linkup file is available, its contents are executed when the PPP connection is established. See the provided "pmdemand" ex- ample in /usr/share/examples/ppp/ppp.conf.sample which runs a script in the background after the connection is established (refer to the "shell" and "bg" commands below for a description of possible substitution strings). Similarly, when a connection is closed, the contents of the /etc/ppp/ppp.linkdown file are executed. Both of these files have the same format as /etc/ppp/ppp.conf. In previous versions of ppp, it was necessary to re-add routes such as the default route in the ppp.linkup file. ppp supports `sticky routes', where all routes that contain the HISADDR, MYADDR, HISADDR6 or MYADDR6 literals will automatically be updated when the values of these variables change. BACKGROUND DIALING If you want to establish a connection using ppp non-interactively (such as from a crontab(5) entry or an at(1) job) you should use the -background option. When -background is specified, ppp attempts to es- tablish the connection immediately. If multiple phone numbers are speci- fied, each phone number will be tried once. If the attempt fails, ppp exits immediately with a non-zero exit code. If it succeeds, then ppp becomes a daemon, and returns an exit status of zero to its caller. The daemon exits automatically if the connection is dropped by the remote system, or it receives a TERM signal. DIAL ON DEMAND Demand dialing is enabled with the -auto or -ddial options. You must also specify the destination label in /etc/ppp/ppp.conf to use. It must contain the "set ifaddr" command to define the remote peers IP address. (refer to /usr/share/examples/ppp/ppp.conf.sample) # ppp -auto pmdemand When -auto or -ddial is specified, ppp runs as a daemon but you can still configure or examine its configuration by using the "set server" command in /etc/ppp/ppp.conf, (for example, "set server +3000 mypasswd") and con- necting to the diagnostic port as follows: # pppctl 3000 (assuming tun0) Password: PPP ON awfulhak> show who tcp (127.0.0.1:1028) * The "show who" command lists users that are currently connected to ppp itself. If the diagnostic socket is closed or changed to a different socket, all connections are immediately dropped. In -auto mode, when an outgoing packet is detected, ppp will perform the dialing action (chat script) and try to connect with the peer. In -ddial mode, the dialing action is performed any time the line is found to be down. If the connect fails, the default behaviour is to wait 30 seconds and then attempt to connect when another outgoing packet is detected. This behaviour can be changed using the "set redial" command: set redial secs[+inc[-max]][.next] [attempts] secs is the number of seconds to wait before attempting to connect again. If the argument is the literal string `random', the de- lay period is a random value between 1 and 30 seconds inclu- sive. inc is the number of seconds that secs should be incremented each time a new dial attempt is made. The timeout reverts to secs only after a successful connection is established. The default value for inc is zero. max is the maximum number of times ppp should increment secs. The default value for max is 10. next is the number of seconds to wait before attempting to dial the next number in a list of numbers (see the "set phone" command). The default is 3 seconds. Again, if the argument is the lit- eral string `random', the delay period is a random value be- tween 1 and 30 seconds. attempts is the maximum number of times to try to connect for each out- going packet that triggers a dial. The previous value is un- changed if this parameter is omitted. If a value of zero is specified for attempts, ppp will keep trying until a connection is made. So, for example: set redial 10.3 4 will attempt to connect 4 times for each outgoing packet that causes a dial attempt with a 3 second delay between each number and a 10 second delay after all numbers have been tried. If multiple phone numbers are specified, the total number of attempts is still 4 (it does not attempt each number 4 times). Alternatively, set redial 10+10-5.3 20 tells ppp to attempt to connect 20 times. After the first attempt, ppp pauses for 10 seconds. After the next attempt it pauses for 20 seconds and so on until after the sixth attempt it pauses for 1 minute. The next 14 pauses will also have a duration of one minute. If ppp connects, dis- connects and fails to connect again, the timeout starts again at 10 sec- onds. Modifying the dial delay is very useful when running ppp in -auto mode on both ends of the link. If each end has the same timeout, both ends wind up calling each other at the same time if the link drops and both ends have packets queued. At some locations, the serial link may not be reli- able, and carrier may be lost at inappropriate times. It is possible to have ppp redial should carrier be unexpectedly lost during a session. set reconnect timeout ntries This command tells ppp to re-establish the connection ntries times on loss of carrier with a pause of timeout seconds before each try. For ex- ample, set reconnect 3 5 tells ppp that on an unexpected loss of carrier, it should wait 3 seconds before attempting to reconnect. This may happen up to 5 times before ppp gives up. The default value of ntries is zero (no reconnect). Care should be taken with this option. If the local timeout is slightly longer than the remote timeout, the reconnect feature will always be triggered (up to the given number of times) after the remote side times out and hangs up. NOTE: In this context, losing too many LQRs consti- tutes a loss of carrier and will trigger a reconnect. If the -background flag is specified, all phone numbers are dialed at most once until a con- nection is made. The next number redial period specified with the "set redial" command is honoured, as is the reconnect tries value. If your redial value is less than the number of phone numbers specified, not all the specified numbers will be tried. To terminate the program, type PPP ON awfulhak> close ppp ON awfulhak> quit all A simple "quit" command will terminate the pppctl(8) or telnet(1) connec- tion but not the ppp program itself. You must use "quit all" to termi- nate ppp as well. RECEIVING INCOMING PPP CONNECTIONS (Method 1) To handle an incoming PPP connection request, follow these steps: 1. Make sure the modem and (optionally) /etc/rc.serial is configured correctly. o Use Hardware Handshake (CTS/RTS) for flow control. o Modem should be set to NO echo back (ATE0) and NO results string (ATQ1). 2. Edit /etc/ttys to enable a getty(8) on the port where the modem is attached. For example: ttyd1 "/usr/libexec/getty std.38400" dialup on secure Don't forget to send a HUP signal to the init(8) process to start the getty(8): # kill -HUP 1 It is usually also necessary to train your modem to the same DTR speed as the getty: # ppp ppp ON awfulhak> set device /dev/cuaa1 ppp ON awfulhak> set speed 38400 ppp ON awfulhak> term deflink: Entering terminal mode on /dev/cuaa1 Type `~?' for help at OK at OK atz OK at OK ~. ppp ON awfulhak> quit 3. Create a /usr/local/bin/ppplogin file with the following contents: #! /bin/sh exec /usr/sbin/ppp -direct incoming Direct mode (-direct) lets ppp work with stdin and stdout. You can also use pppctl(8) to connect to a configured diagnostic port, in the same manner as with client-side ppp. Here, the incoming section must be set up in /etc/ppp/ppp.conf. Make sure that the incoming section contains the "allow users" com- mand as appropriate. 4. Prepare an account for the incoming user. ppp:xxxx:66:66:PPP Login User:/home/ppp:/usr/local/bin/ppplogin Refer to the manual entries for adduser(8) and vipw(8) for details. 5. Support for IPCP Domain Name Server and NetBIOS Name Server negotia- tion can be enabled using the "accept dns" and "set nbns" commands. Refer to their descriptions below. RECEIVING INCOMING PPP CONNECTIONS (Method 2) This method differs in that we use ppp to authenticate the connection rather than login(1): 1. Configure your default section in /etc/gettytab with automatic ppp recognition by specifying the "pp" capability: default:\ :pp=/usr/local/bin/ppplogin:\ ..... 2. Configure your serial device(s), enable a getty(8) and create /usr/local/bin/ppplogin as in the first three steps for method 1 above. 3. Add either "enable chap" or "enable pap" (or both) to /etc/ppp/ppp.conf under the `incoming' label (or whatever label ppplogin uses). 4. Create an entry in /etc/ppp/ppp.secret for each incoming user: Pfred<TAB>xxxx Pgeorge<TAB>yyyy Now, as soon as getty(8) detects a ppp connection (by recognising the HDLC frame headers), it runs "/usr/local/bin/ppplogin". It is VITAL that either PAP or CHAP are enabled as above. If they are not, you are allowing anybody to establish a ppp session with your ma- chine without a password, opening yourself up to all sorts of potential attacks. AUTHENTICATING INCOMING CONNECTIONS Normally, the receiver of a connection requires that the peer authenti- cates itself. This may be done using login(1), but alternatively, you can use PAP or CHAP. CHAP is the more secure of the two, but some clients may not support it. Once you decide which you wish to use, add the command `enable chap' or `enable pap' to the relevant section of ppp.conf. You must then configure the /etc/ppp/ppp.secret file. This file contains one line per possible client, each line containing up to five fields: name key [hisaddr [label [callback-number]]] The name and key specify the client username and password. If key is "*" and PAP is being used, ppp will look up the password database (passwd(5)) when authenticating. If the client does not offer a suitable response based on any name/key combination in ppp.secret, authentication fails. If authentication is successful, hisaddr (if specified) is used when ne- gotiating IP numbers. See the "set ifaddr" command for details. If authentication is successful and label is specified, the current sys- tem label is changed to match the given label. This will change the sub- sequent parsing of the ppp.linkup and ppp.linkdown files. If authentication is successful and callback-number is specified and "set callback" has been used in ppp.conf, the client will be called back on the given number. If CBCP is being used, callback-number may also con- tain a list of numbers or a "*", as if passed to the "set cbcp" command. The value will be used in ppp's subsequent CBCP phase. PPP OVER TCP and UDP (a.k.a Tunnelling) Instead of running ppp over a serial link, it is possible to use a TCP connection instead by specifying the host, port and protocol as the de- vice: set device ui-gate:6669/tcp Instead of opening a serial device, ppp will open a TCP connection to the given machine on the given socket. It should be noted however that ppp doesn't use the telnet protocol and will be unable to negotiate with a telnet server. You should set up a port for receiving this PPP connec- tion on the receiving machine (ui-gate). This is done by first updating /etc/services to name the service: ppp-in 6669/tcp # Incoming PPP connections over TCP and updating /etc/inetd.conf to tell inetd(8) how to deal with incoming connections on that port: ppp-in stream tcp nowait root /usr/sbin/ppp ppp -direct ppp-in Don't forget to send a HUP signal to inetd(8) after you've updated /etc/inetd.conf. Here, we use a label named "ppp-in". The entry in /etc/ppp/ppp.conf on ui-gate (the receiver) should contain the following: ppp-in: set timeout 0 set ifaddr 10.0.4.1 10.0.4.2 and the entry in /etc/ppp/ppp.linkup should contain: ppp-in: add 10.0.1.0/24 HISADDR It is necessary to put the "add" command in ppp.linkup to ensure that the route is only added after ppp has negotiated and assigned addresses to its interface. You may also want to enable PAP or CHAP for security. To enable PAP, add the following line: enable PAP You'll also need to create the following entry in /etc/ppp/ppp.secret: MyAuthName MyAuthPasswd If MyAuthPasswd is a "*", the password is looked up in the passwd(5) database. The entry in /etc/ppp/ppp.conf on awfulhak (the initiator) should contain the following: ui-gate: set escape 0xff set device ui-gate:ppp-in/tcp set dial set timeout 30 set log Phase Chat Connect hdlc LCP IPCP IPV6CP CCP tun set ifaddr 10.0.4.2 10.0.4.1 with the route setup in /etc/ppp/ppp.linkup: ui-gate: add 10.0.2.0/24 HISADDR Again, if you're enabling PAP, you'll also need this in the /etc/ppp/ppp.conf profile: set authname MyAuthName set authkey MyAuthKey We're assigning the address of 10.0.4.1 to ui-gate, and the address 10.0.4.2 to awfulhak. To open the connection, just type awfulhak # ppp -background ui-gate The result will be an additional "route" on awfulhak to the 10.0.2.0/24 network via the TCP connection, and an additional "route" on ui-gate to the 10.0.1.0/24 network. The networks are effectively bridged - the un- derlying TCP connection may be across a public network (such as the In- ternet), and the PPP traffic is conceptually encapsulated (although not packet by packet) inside the TCP stream between the two gateways. The major disadvantage of this mechanism is that there are two "guaran- teed delivery" mechanisms in place - the underlying TCP stream and what- ever protocol is used over the PPP link - probably TCP again. If packets are lost, both levels will get in each others way trying to negotiate sending of the missing packet. To avoid this overhead, it is also possible to do all this using UDP in- stead of TCP as the transport by simply changing the protocol from "tcp" to "udp". When using UDP as a transport, ppp will operate in synchronous mode. This is another gain as the incoming data does not have to be re- arranged into packets. Care should be taken when adding a default route through a tunneled setup like this. It is quite common for the default route (added in /etc/ppp/ppp.linkup) to end up routing the link's TCP connection through the tunnel, effectively garrotting the connection. To avoid this, make sure you add a static route for the benefit of the link: ui-gate: set escape 0xff set device ui-gate:ppp-in/tcp add ui-gate x.x.x.x ..... where "x.x.x.x" is the IP number that your route to "ui-gate" would nor- mally use. When routing your connection accross a public network such as the Inter- net, it is preferable to encrypt the data. This can be done with the help of the MPPE protocol, although currently this means that you will not be able to also compress the traffic as MPPE is implemented as a com- pression layer (thank Microsoft for this). To enable MPPE encryption, add the following lines to /etc/ppp/ppp.conf on the server: enable MSCHAPv2 disable deflate pred1 deny deflate pred1 ensuring that you've put the requisite entry in /etc/ppp/ppp.secret (MSCHAPv2 is challenge based, so passwd(5) cannot be used) MSCHAPv2 and MPPE are accepted by default, so the client end should work without any additional changes (although ensure you have "set authname" and "set authkey" in your profile). NETWORK ADDRESS TRANSLATION (PACKET ALIASING) The -nat command line option enables network address translation (a.k.a. packet aliasing). This allows the ppp host to act as a masquerading gateway for other computers over a local area network. Outgoing IP pack- ets are NAT'd so that they appear to come from the ppp host, and incoming packets are de-NAT'd so that they are routed to the correct machine on the local area network. NAT allows computers on private, unregistered subnets to have Internet access, although they are invisible from the outside world. In general, correct ppp operation should first be veri- fied with network address translation disabled. Then, the -nat option should be switched on, and network applications (web browser, telnet(1), ftp(1), ping(8), traceroute(8)) should be checked on the ppp host. Fi- nally, the same or similar applications should be checked on other com- puters in the LAN. If network applications work correctly on the ppp host, but not on other machines in the LAN, then the masquerading soft- ware is working properly, but the host is either not forwarding or possi- bly receiving IP packets. Check that IP forwarding is enabled in /etc/rc.conf and that other machines have designated the ppp host as the gateway for the LAN. PACKET FILTERING This implementation supports packet filtering. There are four kinds of filters: the in filter, the out filter, the dial filter and the alive filter. Here are the basics: o A filter definition has the following syntax: set filter name rule-no action [!] [[host] src_addr[/width] [dst_addr[/width]]] [proto [src cmp port] [dst cmp port] [estab] [syn] [finrst] [timeout secs]] 1. Name should be one of `in', `out', `dial' or `alive'. 2. Rule-no is a numeric value between `0' and `39' specifying the rule number. Rules are specified in numeric order according to rule-no, but only if rule `0' is defined. 3. Action may be specified as `permit' or `deny', in which case, if a given packet matches the rule, the associated action is taken immediately. Action can also be specified as `clear' to clear the action associated with that particular rule, or as a new rule number greater than the current rule. In this case, if a given packet matches the current rule, the packet will next be matched against the new rule number (rather than the next rule number). The action may optionally be followed with an exclamation mark ("!"), telling ppp to reverse the sense of the following match. 4. [src_addr[/width]] and [dst_addr[/width]] are the source and destination IP number specifications. If [/width] is specified, it gives the number of relevant netmask bits, allowing the spec- ification of an address range. Either src_addr or dst_addr may be given the values MYADDR, HISADDR, MYADDR6 or HISADDR6 (refer to the description of the "bg" command for a description of these values). When these values are used, the filters will be updated any time the values change. This is similar to the behaviour of the "add" command below. 5. Proto may be any protocol from protocols(5). 6. Cmp is one of `lt', `eq' or `gt', meaning less-than, equal and greater-than respectively. Port can be specified as a numeric port or by service name from /etc/services. 7. The `estab', `syn', and `finrst' flags are only allowed when proto is set to `tcp', and represent the TH_ACK, TH_SYN and TH_FIN or TH_RST TCP flags respectively. 8. The timeout value adjusts the current idle timeout to at least secs seconds. If a timeout is given in the alive filter as well as in the in/out filter, the in/out value is used. If no time- out is given, the default timeout (set using set timeout and de- faulting to 180 seconds) is used. o Each filter can hold up to 40 rules, starting from rule 0. The en- tire rule set is not effective until rule 0 is defined, i.e., the de- fault is to allow everything through. o If no rule in a defined set of rules matches a packet, that packet will be discarded (blocked). If there are no rules in a given fil- ter, the packet will be permitted. o It's possible to filter based on the payload of UDP frames where those frames contain a PROTO_IP PPP frame header. See the filter-decapsulation option below for further details. o Use "set filter name -1" to flush all rules. See /usr/share/examples/ppp/ppp.conf.sample. SETTING THE IDLE TIMER To check/set the idle timer, use the "show bundle" and "set timeout" com- mands: ppp ON awfulhak> set timeout 600 The timeout period is measured in seconds, the default value for which is 180 seconds (or 3 min). To disable the idle timer function, use the com- mand ppp ON awfulhak> set timeout 0 In -ddial and -dedicated modes, the idle timeout is ignored. In -auto mode, when the idle timeout causes the PPP session to be closed, the ppp program itself remains running. Another trigger packet will cause it to attempt to re-establish the link. PREDICTOR-1 and DEFLATE COMPRESSION ppp supports both Predictor type 1 and deflate compression. By default, ppp will attempt to use (or be willing to accept) both compression proto- cols when the peer agrees (or requests them). The deflate protocol is preferred by ppp. Refer to the "disable" and "deny" commands if you wish to disable this functionality. It is possible to use a different compression algorithm in each direction by using only one of "disable deflate" and "deny deflate" (assuming that the peer supports both algorithms). By default, when negotiating DEFLATE, ppp will use a window size of 15. Refer to the "set deflate" command if you wish to change this behaviour. A special algorithm called DEFLATE24 is also available, and is disabled and denied by default. This is exactly the same as DEFLATE except that it uses CCP ID 24 to negotiate. This allows ppp to successfully negoti- ate DEFLATE with pppd version 2.3.*. CONTROLLING IP ADDRESS For IPv4, ppp uses IPCP to negotiate IP addresses. Each side of the con- nection specifies the IP address that it's willing to use, and if the re- quested IP address is acceptable then ppp returns an ACK to the re- quester. Otherwise, ppp returns NAK to suggest that the peer use a dif- ferent IP address. When both sides of the connection agree to accept the received request (and send an ACK), IPCP is set to the open state and a network level connection is established. To control this IPCP behaviour, this implementation has the "set ifaddr" command for defining the local and remote IP address: set ifaddr [src_addr[/nn] [dst_addr[/nn] [netmask [trigger_addr]]]] where, `src_addr' is the IP address that the local side is willing to use, `dst_addr' is the IP address which the remote side should use and `netmask' is the netmask that should be used. `Src_addr' defaults to the current hostname(1), `dst_addr' defaults to 0.0.0.0, and `netmask' de- faults to whatever mask is appropriate for `src_addr'. It is only possi- ble to make `netmask' smaller than the default. The usual value is 255.255.255.255, as most kernels ignore the netmask of a POINTOPOINT in- terface. Some incorrect PPP implementations require that the peer negotiates a specific IP address instead of `src_addr'. If this is the case, `trigger_addr' may be used to specify this IP number. This will not af- fect the routing table unless the other side agrees with this proposed number. set ifaddr 192.244.177.38 192.244.177.2 255.255.255.255 0.0.0.0 The above specification means: o I will first suggest that my IP address should be 0.0.0.0, but I will only accept an address of 192.244.177.38. o I strongly insist that the peer uses 192.244.177.2 as his own address and won't permit the use of any IP address but 192.244.177.2. When the peer requests another IP address, I will always suggest that it uses 192.244.177.2. o The routing table entry will have a netmask of 0xffffffff. This is all fine when each side has a pre-determined IP address, however it is often the case that one side is acting as a server which controls all IP addresses and the other side should go along with it. In order to allow more flexible behaviour, the "set ifaddr" command allows the user to specify IP addresses more loosely: set ifaddr 192.244.177.38/24 192.244.177.2/20 A number followed by a slash ("/") represents the number of bits signifi- cant in the IP address. The above example means: o I'd like to use 192.244.177.38 as my address if it is possible, but I'll also accept any IP address between 192.244.177.0 and 192.244.177.255. o I'd like to make him use 192.244.177.2 as his own address, but I'll also permit him to use any IP address between 192.244.176.0 and 192.244.191.255. o As you may have already noticed, 192.244.177.2 is equivalent to say- ing 192.244.177.2/32. o As an exception, 0 is equivalent to 0.0.0.0/0, meaning that I have no preferred IP address and will obey the remote peers selection. When using zero, no routing table entries will be made until a connection is established. o 192.244.177.2/0 means that I'll accept/permit any IP address but I'll suggest that 192.244.177.2 be used first. When negotiating IPv6 addresses, no control is given to the user. IPV6CP negotiation is fully automatic. CONNECTING WITH YOUR INTERNET SERVICE PROVIDER The following steps should be taken when connecting to your ISP: 1. Describe your providers phone number(s) in the dial script using the "set phone" command. This command allows you to set multiple phone numbers for dialing and redialing separated by either a pipe ("|") or a colon (":"): set phone telno[|backupnumber]...[:nextnumber]... Numbers after the first in a pipe-separated list are only used if the previous number was used in a failed dial or login script. Num- bers separated by a colon are used sequentially, irrespective of what happened as a result of using the previous number. For exam- ple: set phone "1234567|2345678:3456789|4567890" Here, the 1234567 number is attempted. If the dial or login script fails, the 2345678 number is used next time, but *only* if the dial or login script fails. On the dial after this, the 3456789 number is used. The 4567890 number is only used if the dial or login script using the 3456789 fails. If the login script of the 2345678 number fails, the next number is still the 3456789 number. As many pipes and colons can be used as are necessary (although a given site would usually prefer to use either the pipe or the colon, but not both). The next number redial timeout is used between all numbers. When the end of the list is reached, the normal redial period is used before starting at the beginning again. The selected phone number is substituted for the \\T string in the "set dial" command (see below). 2. Set up your redial requirements using "set redial". For example, if you have a bad telephone line or your provider is usually engaged (not so common these days), you may want to specify the following: set redial 10 4 This says that up to 4 phone calls should be attempted with a pause of 10 seconds before dialing the first number again. 3. Describe your login procedure using the "set dial" and "set login" commands. The "set dial" command is used to talk to your modem and establish a link with your ISP, for example: set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 4 \"\" \ ATZ OK-ATZ-OK ATDT\\T TIMEOUT 60 CONNECT" This modem "chat" string means: o Abort if the string "BUSY" or "NO CARRIER" are received. o Set the timeout to 4 seconds. o Expect nothing. o Send ATZ. o Expect OK. If that's not received within the 4 second timeout, send ATZ and expect OK. o Send ATDTxxxxxxx where xxxxxxx is the next number in the phone list from above. o Set the timeout to 60. o Wait for the CONNECT string. Once the connection is established, the login script is executed. This script is written in the same style as the dial script, but care should be taken to avoid having your password logged: set authkey MySecret set login "TIMEOUT 15 login:-\\r-login: awfulhak \ word: \\P ocol: PPP HELLO" This login "chat" string means: o Set the timeout to 15 seconds. o Expect "login:". If it's not received, send a carriage return and expect "login:" again. o Send "awfulhak" o Expect "word:" (the tail end of a "Password:" prompt). o Send whatever our current authkey value is set to. o Expect "ocol:" (the tail end of a "Protocol:" prompt). o Send "PPP". o Expect "HELLO". The "set authkey" command is logged specially. When command or chat logging is enabled, the actual password is not logged; `********' is logged instead. Login scripts vary greatly between ISPs. If you're setting one up for the first time, ENABLE CHAT LOGGING so that you can see if your script is behaving as you expect. 4. Use "set device" and "set speed" to specify your serial line and speed, for example: set device /dev/cuaa0 set speed 115200 Cuaa0 is the first serial port on FreeBSD. If you're running ppp on OpenBSD, cua00 is the first. A speed of 115200 should be specified if you have a modem capable of bit rates of 28800 or more. In gen- eral, the serial speed should be about four times the modem speed. 5. Use the "set ifaddr" command to define the IP address. o If you know what IP address your provider uses, then use it as the remote address (dst_addr), otherwise choose something like 10.0.0.2/0 (see below). o If your provider has assigned a particular IP address to you, then use it as your address (src_addr). o If your provider assigns your address dynamically, choose a suitably unobtrusive and unspecific IP number as your address. 10.0.0.1/0 would be appropriate. The bit after the / specifies how many bits of the address you consider to be important, so if you wanted to insist on something in the class C network 1.2.3.0, you could specify 1.2.3.1/24. o If you find that your ISP accepts the first IP number that you suggest, specify third and forth arguments of "0.0.0.0". This will force your ISP to assign a number. (The third argument will be ignored as it is less restrictive than the default mask for your `src_addr'). An example for a connection where you don't know your IP number or your ISPs IP number would be: set ifaddr 10.0.0.1/0 10.0.0.2/0 0.0.0.0 0.0.0.0 6. In most cases, your ISP will also be your default router. If this is the case, add the line add default HISADDR to /etc/ppp/ppp.conf (or to /etc/ppp/ppp.linkup for setups that don't use -auto mode). This tells ppp to add a default route to whatever the peer address is (10.0.0.2 in this example). This route is `sticky', meaning that should the value of HISADDR change, the route will be updated ac- cordingly. 7. If your provider requests that you use PAP/CHAP authentication meth- ods, add the next lines to your /etc/ppp/ppp.conf file: set authname MyName set authkey MyPassword Both are accepted by default, so ppp will provide whatever your ISP requires. It should be noted that a login script is rarely (if ever) required when PAP or CHAP are in use. 8. Ask your ISP to authenticate your nameserver address(es) with the line enable dns Do NOT do this if you are running a local DNS unless you also either use "resolv readonly" or have "resolv restore" in /etc/ppp/ppp.linkdown, as ppp will simply circumvent its use by en- tering some nameserver lines in /etc/resolv.conf. Please refer to /usr/share/examples/ppp/ppp.conf.sample and /usr/share/examples/ppp/ppp.linkup.sample for some real examples. The pmdemand label should be appropriate for most ISPs. LOGGING FACILITY ppp is able to generate the following log info either via syslog(3) or directly to the screen: All Enable all logging facilities. This generates a lot of log. The most common use of 'all' is as a basis, where you remove some facilities after enabling 'all' ('debug' and 'timer' are usually best disabled.) Async Dump async level packet in hex. CBCP Generate CBCP (CallBack Control Protocol) logs. CCP Generate a CCP packet trace. Chat Generate `dial', `login', `logout' and `hangup' chat script trace logs. Command Log commands executed either from the command line or any of the configuration files. Connect Log Chat lines containing the string "CONNECT". Debug Log debug information. DNS Log DNS QUERY packets. Filter Log packets permitted by the dial filter and denied by any filter. HDLC Dump HDLC packet in hex. ID0 Log all function calls specifically made as user id 0. IPCP Generate an IPCP packet trace. LCP Generate an LCP packet trace. LQM Generate LQR reports. Phase Phase transition log output. Physical Dump physical level packet in hex. Sync Dump sync level packet in hex. TCP/IP Dump all TCP/IP packets. Timer Log timer manipulation. TUN Include the tun device on each log line. Warning Output to the terminal device. If there is currently no terminal, output is sent to the log file using syslogs LOG_WARNING. Error Output to both the terminal device and the log file using syslogs LOG_ERROR. Alert Output to the log file using LOG_ALERT. The "set log" command allows you to set the logging output level. Multi- ple levels can be specified on a single command line. The default is equivalent to "set log Phase". It is also possible to log directly to the screen. The syntax is the same except that the word "local" should immediately follow "set log". The default is "set log local" (i.e., only the un-maskable warning, error and alert output). If The first argument to "set log [local]" begins with a `+' or a `-' character, the current log levels are not cleared, for example: PPP ON awfulhak> set log phase PPP ON awfulhak> show log Log: Phase Warning Error Alert Local: Warning Error Alert PPP ON awfulhak> set log +tcp/ip -warning PPP ON awfulhak> set log local +command PPP ON awfulhak> show log Log: Phase TCP/IP Warning Error Alert Local: Command Warning Error Alert Log messages of level Warning, Error and Alert are not controllable using "set log [local]". The Warning level is special in that it will not be logged if it can be displayed locally. SIGNAL HANDLING ppp deals with the following signals: INT Receipt of this signal causes the termination of the current con- nection (if any). This will cause ppp to exit unless it is in -auto or -ddial mode. HUP, TERM & QUIT These signals tell ppp to exit. USR1 This signal, tells ppp to re-open any existing server socket, drop- ping all existing diagnostic connections. Sockets that couldn't previously be opened will be retried. USR2 This signal, tells ppp to close any existing server socket, drop- ping all existing diagnostic connections. SIGUSR1 can still be used to re-open the socket. MULTI-LINK PPP If you wish to use more than one physical link to connect to a PPP peer, that peer must also understand the MULTI-LINK PPP protocol. Refer to RFC 1990 for specification details. The peer is identified using a combination of his "endpoint discriminator" and his "authentication id". Either or both of these may be specified. It is recommended that at least one is specified, other- wise there is no way of ensuring that all links are actually connected to the same peer program, and some confusing lock-ups may result. Locally, these identification variables are specified using the "set enddisc" and "set authname" commands. The `authname' (and `authkey') must be agreed in advance with the peer. Multi-link capabilities are enabled using the "set mrru" command (set maximum reconstructed receive unit). Once multi-link is enabled, ppp will attempt to negotiate a multi-link connection with the peer. By default, only one `link' is available (called `deflink'). To create more links, the "clone" command is used. This command will clone exist- ing links, where all characteristics are the same except: 1. The new link has its own name as specified on the "clone" command line. 2. The new link is an `interactive' link. Its mode may subsequently be changed using the "set mode" command. 3. The new link is in a `closed' state. A summary of all available links can be seen using the "show links" com- mand. Once a new link has been created, command usage varies. All link spe- cific commands must be prefixed with the "link name" command, specifying on which link the command is to be applied. When only a single link is available, ppp is smart enough not to require the "link name" prefix. Some commands can still be used without specifying a link - resulting in an operation at the `bundle' level. For example, once two or more links are available, the command "show ccp" will show CCP configuration and statistics at the multi-link level, and "link deflink show ccp" will show the same information at the "deflink" link level. Armed with this information, the following configuration might be used: mp: set timeout 0 set log phase chat set device /dev/cuaa0 /dev/cuaa1 /dev/cuaa2 set phone "123456789" set dial "ABORT BUSY ABORT NO\sCARRIER TIMEOUT 5 \"\" ATZ \ OK-AT-OK \\dATDT\\T TIMEOUT 45 CONNECT" set login set ifaddr 10.0.0.1/0 10.0.0.2/0 0.0.0.0 0.0.0.0 set authname ppp set authkey ppppassword set mrru 1500 clone 1,2,3 # Create 3 new links - duplicates of the default link deflink remove # Delete the default link (called ``deflink'') Note how all cloning is done at the end of the configuration. Usually, the link will be configured first, then cloned. If you wish all links to be up all the time, you can add the following line to the end of your configuration. link 1,2,3 set mode ddial If you want the links to dial on demand, this command could be used: link * set mode auto Links may be tied to specific names by removing the "set device" line above, and specifying the following after the "clone" command: link 1 set device /dev/cuaa0 link 2 set device /dev/cuaa1 link 3 set device /dev/cuaa2 Use the "help" command to see which commands require context (using the "link" command), which have optional context and which should not have any context. When ppp has negotiated MULTI-LINK mode with the peer, it creates a local domain socket in the /var/run directory. This socket is used to pass link information (including the actual link file descriptor) between dif- ferent ppp invocations. This facilitates ppp's ability to be run from a getty(8) or directly from /etc/gettydefs (using the `pp=' capability), without needing to have initial control of the serial line. Once ppp ne- gotiates multi-link mode, it will pass its open link to any already run- ning process. If there is no already running process, ppp will act as the master, creating the socket and listening for new connections. PPP COMMAND LIST This section lists the available commands and their effect. They are us- able either from an interactive ppp session, from a configuration file or from a pppctl(8) or telnet(1) session. accept|deny|enable|disable option.... These directives tell ppp how to negotiate the initial connection with the peer. Each "option" has a default of either accept or deny and enable or disable. "Accept" means that the option will be ACK'd if the peer asks for it. "Deny" means that the option will be NAK'd if the peer asks for it. "Enable" means that the option will be re- quested by us. "Disable" means that the option will not be requested by us. "Option" may be one of the following: acfcomp Default: Enabled and Accepted. ACFComp stands for Address and Control Field Compression. Non LCP packets will usually have an address field of 0xff (the All-Stations address) and a control field of 0x03 (the Unnumbered Information command). If this op- tion is negotiated, these two bytes are simply not sent, thus minimising traffic. See rfc1662 for details. chap[05] Default: Disabled and Accepted. CHAP stands for Challenge Hand- shake Authentication Protocol. Only one of CHAP and PAP (below) may be negotiated. With CHAP, the authenticator sends a "chal- lenge" message to its peer. The peer uses a one-way hash func- tion to encrypt the challenge and sends the result back. The au- thenticator does the same, and compares the results. The advan- tage of this mechanism is that no passwords are sent across the connection. A challenge is made when the connection is first made. Subsequent challenges may occur. If you want to have your peer authenticate itself, you must "enable chap". in /etc/ppp/ppp.conf, and have an entry in /etc/ppp/ppp.secret for the peer. When using CHAP as the client, you need only specify "AuthName" and "AuthKey" in /etc/ppp/ppp.conf. CHAP is accepted by default. Some PPP implementations use "MS-CHAP" rather than MD5 when en- crypting the challenge. MS-CHAP is a combination of MD4 and DES. If ppp was built on a machine with DES libraries available, it will respond to MS-CHAP authentication requests, but will never request them. deflate Default: Enabled and Accepted. This option decides if deflate compression will be used by the Compression Control Protocol (CCP). This is the same algorithm as used by the gzip(1) pro- gram. Note: There is a problem negotiating deflate capabilities with pppd(8) - a PPP implementation available under many operat- ing systems. pppd (version 2.3.1) incorrectly attempts to nego- tiate deflate compression using type 24 as the CCP configuration type rather than type 26 as specified in rfc1979. Type 24 is ac- tually specified as "PPP Magna-link Variable Resource Compression" in rfc1975! ppp is capable of negotiating with pppd, but only if "deflate24" is enabled and accepted. deflate24 Default: Disabled and Denied. This is a variance of the deflate option, allowing negotiation with the pppd(8) program. Refer to the deflate section above for details. It is disabled by default as it violates rfc1975. dns Default: Disabled and Denied. This option allows DNS negotia- tion. If "enabled," ppp will request that the peer confirms the entries in /etc/resolv.conf. If the peer NAKs our request (suggesting new IP numbers), /etc/resolv.conf is updated and another request is sent to confirm the new entries. If "accepted," ppp will answer any DNS queries requested by the peer rather than rejecting them. The answer is taken from /etc/resolv.conf unless the "set dns" command is used as an over- ride. enddisc Default: Enabled and Accepted. This option allows control over whether we negotiate an endpoint discriminator. We only send our discriminator if "set enddisc" is used and enddisc is enabled. We reject the peers discriminator if enddisc is denied. LANMan|chap80lm Default: Disabled and Accepted. The use of this authentication protocol is discouraged as it partially violates the authentica- tion protocol by implementing two different mechanisms (LANMan & NT) under the guise of a single CHAP type (0x80). "LANMan" uses a simple DES encryption mechanism and is the least secure of the CHAP alternatives (although is still more secure than PAP). Refer to the "MSChap" description below for more details. lqr Default: Disabled and Accepted. This option decides if Link Quality Requests will be sent or accepted. LQR is a protocol that allows ppp to determine that the link is down without rely- ing on the modems carrier detect. When LQR is enabled, ppp sends the QUALPROTO option (see "set lqrperiod" below) as part of the LCP request. If the peer agrees, both sides will exchange LQR packets at the agreed frequency, allowing detailed link quality monitoring by enabling LQM logging. If the peer doesn't agree, ppp will send ECHO LQR requests instead. These packets pass no information of interest, but they MUST be replied to by the peer. Whether using LQR or ECHO LQR, ppp will abruptly drop the connec- tion if 5 unacknowledged packets have been sent rather than send- ing a 6th. A message is logged at the PHASE level, and any ap- propriate "reconnect" values are honoured as if the peer were re- sponsible for dropping the connection. mppe Default: Enabled and Accepted. This is Microsoft Point to Point Encryption scheme. MPPE key size can be 40-, 56- and 128-bits. Refer to "set mppe" command. MSChapV2|chap81 Default: Disabled and Accepted. It is very similar to standard CHAP (type 0x05) except that it issues challenges of a fixed 16 bytes in length and uses a combination of MD4, SHA-1 and DES to encrypt the challenge rather than using the standard MD5 mecha- nism. MSChap|chap80nt Default: Disabled and Accepted. The use of this authentication protocol is discouraged as it partially violates the authentica- tion protocol by implementing two different mechanisms (LANMan & NT) under the guise of a single CHAP type (0x80). It is very similar to standard CHAP (type 0x05) except that it issues chal- lenges of a fixed 8 bytes in length and uses a combination of MD4 and DES to encrypt the challenge rather than using the standard MD5 mechanism. CHAP type 0x80 for LANMan is also supported - see "enable LANMan" for details. Because both "LANMan" and "NT" use CHAP type 0x80, when acting as authenticator with both "enabled", ppp will rechallenge the peer up to three times if it responds using the wrong one of the two protocols. This gives the peer a chance to attempt using both protocols. Conversely, when ppp acts as the authenticatee with both proto- cols "accepted", the protocols are used alternately in response to challenges. Note: If only LANMan is enabled, pppd(8) (version 2.3.5) misbe- haves when acting as authenticatee. It provides both the NT and the LANMan answers, but also suggests that only the NT answer should be used. pap Default: Disabled and Accepted. PAP stands for Password Authen- tication Protocol. Only one of PAP and CHAP (above) may be nego- tiated. With PAP, the ID and Password are sent repeatedly to the peer until authentication is acknowledged or the connection is terminated. This is a rather poor security mechanism. It is only performed when the connection is first established. If you want to have your peer authenticate itself, you must "enable pap". in /etc/ppp/ppp.conf, and have an entry in /etc/ppp/ppp.secret for the peer (although see the "passwdauth" and "set radius" options below). When using PAP as the client, you need only specify "AuthName" and "AuthKey" in /etc/ppp/ppp.conf. PAP is accepted by default. pred1 Default: Enabled and Accepted. This option decides if Predictor 1 compression will be used by the Compression Control Protocol (CCP). protocomp Default: Enabled and Accepted. This option is used to negotiate PFC (Protocol Field Compression), a mechanism where the protocol field number is reduced to one octet rather than two. shortseq Default: Enabled and Accepted. This option determines if ppp will request and accept requests for short (12 bit) sequence num- bers when negotiating multi-link mode. This is only applicable if our MRRU is set (thus enabling multi-link). vjcomp Default: Enabled and Accepted. This option determines if Van Ja- cobson header compression will be used. The following options are not actually negotiated with the peer. Therefore, accepting or denying them makes no sense. filter-decapsulation Default: Disabled. When this option is enabled, ppp will examine UDP frames to see if they actually contain a PPP frame as their payload. If this is the case, all filters will operate on the payload rather than the actual packet. This is useful if you want to send PPPoUDP traffic over a PPP link, but want that link to do smart things with the real data rather than the UDP wrapper. The UDP frame payload must not be compressed in any way, other- wise ppp will not be able to interpret it. It's therefore recom- mended that you disable vj pred1 deflate and deny vj pred1 deflate in the configuration for the ppp invocation with the udp link. idcheck Default: Enabled. When ppp exchanges low-level LCP, CCP and IPCP configuration traffic, the Identifier field of any replies is ex- pected to be the same as that of the request. By default, ppp drops any reply packets that do not contain the expected identi- fier field, reporting the fact at the respective log level. If idcheck is disabled, ppp will ignore the identifier field. iface-alias Default: Enabled if -nat is specified. This option simply tells ppp to add new interface addresses to the interface rather than replacing them. The option can only be enabled if network ad- dress translation is enabled ("nat enable yes"). With this option enabled, ppp will pass traffic for old interface addresses through the NAT engine (see libalias(3)), resulting in the ability (in -auto mode) to properly connect the process that caused the PPP link to come up in the first place. Disabling NAT with "nat enable no" will also disable `iface-alias'. ipcp Default: Enabled. This option allows ppp to attempt to negotiate IP control protocol capabilities and if successful to exchange IP datagrams with the peer. ipv6cp Default: Enabled. This option allows ppp to attempt to negotiate IPv6 control protocol capabilities and if successful to exchange IPv6 datagrams with the peer. keep-session Default: Disabled. When ppp runs as a Multi-link server, a dif- ferent ppp instance initially receives each connection. After determining that the link belongs to an already existing bundle (controlled by another ppp invocation), ppp will transfer the link to that process. If the link is a tty device or if this option is enabled, ppp will not exit, but will change its process name to "session owner" and wait for the controlling ppp to finish with the link and deliver a signal back to the idle process. This prevents the confusion that results from ppp's parent considering the link re- source available again. For tty devices that have entries in /etc/ttys, this is necessary to prevent another getty(8) from being started, and for program links such as sshd(8), it prevents sshd(8) from exiting due to the death of its child. As ppp cannot determine its parents re- quirements (except for the tty case), this option must be enabled manually depending on the circumstances. loopback Default: Enabled. When loopback is enabled, ppp will automati- cally loop back packets being sent out with a destination address equal to that of the PPP interface. If disabled, ppp will send the packet, probably resulting in an ICMP redirect from the other end. It is convenient to have this option enabled when the in- terface is also the default route as it avoids the necessity of a loopback route. passwdauth Default: Disabled. Enabling this option will tell the PAP au- thentication code to use the password database (see passwd(5)) to authenticate the caller if they cannot be found in the /etc/ppp/ppp.secret file. /etc/ppp/ppp.secret is always checked first. If you wish to use passwords from passwd(5), but also to specify an IP number or label for a given client, use "*" as the client password in /etc/ppp/ppp.secret. proxy Default: Disabled. Enabling this option will tell ppp to proxy ARP for the peer. This means that ppp will make an entry in the ARP table using HISADDR and the MAC address of the local network in which HISADDR appears. This allows other machines connecteed to the LAN to talk to the peer as if the peer itself was con- nected to the LAN. The proxy entry cannot be made unless HISADDR is an address from a LAN. proxyall Default: Disabled. Enabling this will tell ppp to add proxy arp entries for every IP address in all class C or smaller subnets routed via the tun interface. Proxy arp entries are only made for sticky routes that are added using the "add" command. No proxy arp entries are made for the interface address itself (as created by the "set ifaddr" com- mand). sroutes Default: Enabled. When the "add" command is used with the HISADDR, MYADDR, HISADDR6 or MYADDR6 values, entries are stored in the `sticky route' list. Each time these variables change, this list is re-applied to the routing table. Disabling this option will prevent the re-application of sticky routes, although the `stick route' list will still be maintained. [tcp]mssfixup Default: Enabled. This option tells ppp to adjust TCP SYN pack- ets so that the maximum receive segment size is not greater than the amount allowed by the interface MTU. throughput Default: Enabled. This option tells ppp to gather throughput statistics. Input and output is sampled over a rolling 5 second window, and current, best and total figures are retained. This data is output when the relevant PPP layer shuts down, and is also available using the "show" command. Throughput statistics are available at the "IPCP" and "physical" levels. utmp Default: Enabled. Normally, when a user is authenticated using PAP or CHAP, and when ppp is running in -direct mode, an entry is made in the utmp and wtmp files for that user. Disabling this option will tell ppp not to make any utmp or wtmp entries. This is usually only necessary if you require the user to both login and authenticate themselves. add[!] dest[/nn] [mask] [gateway] Dest is the destination IP address. The netmask is specified either as a number of bits with /nn or as an IP number using mask. 0 0 or simply 0 with no mask refers to the default route. It is also possi- ble to use the literal name `default' instead of 0. Gateway is the next hop gateway to get to the given dest machine/network. Refer to the route(8) command for further details. It is possible to use the symbolic names `MYADDR', `HISADDR', `MYADDR6' or `HISADDR6' as the destination, and `HISADDR' or `HISADDR6' as the gateway. `MYADDR' is replaced with the interface IP address, `HISADDR' is replaced with the interface IP destination (peer) address, `MYADDR6' is replaced with the interface IPv6 ad- dress, and `HISADDR6' is replaced with the interface IPv6 destination address, If the add! command is used (note the trailing "!"), then if the route already exists, it will be updated as with the `route change' command (see route(8) for further details). Routes that contain the "HISADDR", "MYADDR", "HISADDR6", "MYADDR6", "DNS0", or "DNS1" constants are considered `sticky'. They are stored in a list (use "show ncp" to see the list), and each time the value of one of these variables changes, the appropriate routing table en- tries are updated. This facility may be disabled using "disable sroutes". allow command [args] This command controls access to ppp and its configuration files. It is possible to allow user-level access, depending on the configura- tion file label and on the mode that ppp is being run in. For exam- ple, you may wish to configure ppp so that only user `fred' may ac- cess label `fredlabel' in -background mode. User id 0 is immune to these commands. allow user[s] logname... By default, only user id 0 is allowed access to ppp. If this command is used, all of the listed users are allowed access to the section in which the "allow users" command is found. The `default' section is always checked first (even though it is only ever automatically loaded at startup). "allow users" commands are cumulative in a given section, but users allowed in any given section override users allowed in the default section, so it's possible to allow users access to everything except a given label by specifying default users in the `default' section, and then specifying a new user list for that label. If user `*' is specified, access is allowed to all users. allow mode[s] mode... By default, access using any ppp mode is possible. If this com- mand is used, it restricts the access modes allowed to load the label under which this command is specified. Again, as with the "allow users" command, each "allow modes" command overrides any previous settings, and the `default' section is always checked first. Possible modes are: `interactive', `auto', `direct', `dedicated', `ddial', `background' and `*'. When running in multi-link mode, a section can be loaded if it allows any of the currently existing line modes. nat command [args] This command allows the control of the network address translation (also known as masquerading or IP aliasing) facilities that are built into ppp. NAT is done on the external interface only, and is un- likely to make sense if used with the -direct flag. If nat is enabled on your system (it may be omitted at compile time), the following commands are possible: nat enable yes|no This command either switches network address translation on or turns it off. The -nat command line flag is synonymous with "nat enable yes". nat addr [addr_local addr_alias] This command allows data for addr_alias to be redirected to addr_local. It is useful if you own a small number of real IP numbers that you wish to map to specific machines behind your gateway. nat deny_incoming yes|no If set to yes, this command will refuse all incoming packets where an aliasing link doesn't already exist. Refer to the CONCEPTUAL BACKGROUND section of libalias(3) for a description of what an "aliasing link" is. It should be noted under what circumstances an aliasing link is created by libalias(3). It may be necessary to further protect your network from outside connections using the "set filter" or "nat target" commands. nat help|? This command gives a summary of available nat commands. nat log yes|no This option causes various NAT statistics and information to be logged to the file /var/log/alias.log. nat port proto targetIP:targetPort[-targetPort] aliasPort[-aliasPort] [remoteIP:remotePort[-remotePort]] This command causes incoming proto connections to aliasPort to be redirected to targetPort on targetIP. proto is either "tcp" or "udp". A range of port numbers may be specified as shown above. The ranges must be of the same size. If remoteIP is specified, only data coming from that IP number is redirected. remotePort must either be "0" (indicating any source port) or a range of ports the same size as the other ranges. This option is useful if you wish to run things like Internet phone on machines behind your gateway, but is limited in that connections to only one interior machine per source machine and target port are possible. nat proto proto localIP [publicIP [remoteIP]] This command tells ppp to redirect packets of protocol type proto (see protocols(5)) to the internal address localIP. If publicIP is specified, only packets destined for that address are matched, otherwise the default alias address is used. If remoteIP is specified, only packets matching that source ad- dress are matched, This command is useful for redirecting tunnel endpoints to an in- ternal machine, for example: nat proto ipencap 10.0.0.1 nat proxy cmd arg... This command tells ppp to proxy certain connections, redirecting them to a given server. Refer to the description of PacketAliasProxyRule() in libalias(3) for details of the avail- able commands. nat punch_fw [base count] This command tells ppp to punch holes in the firewall for FTP or IRC DCC connections. This is done dynamically by installing termporary firewall rules which allow a particular connection (and only that connection) to go through the firewall. The rules are removed once the corresponding connection terminates. A maximum of count rules starting from rule number base will be used for punching firewall holes. The range will be cleared when the "nat punch_fw" command is run. If no arguments are given, firewall punching is disabled. nat same_ports yes|no When enabled, this command will tell the network address transla- tion engine to attempt to avoid changing the port number on out- going packets. This is useful if you want to support protocols such as RPC and LPD which require connections to come from a well known port. nat target [address] Set the given target address or clear it if no address is given. The target address is used by libalias to specify how to NAT in- coming packets by default. If a target address is not set or if "default" is given, packets are not altered and are allowed to route to the internal network. The target address may be set to "MYADDR", in which case libalias will redirect all packets to the interface address. nat use_sockets yes|no When enabled, this option tells the network address translation engine to create a socket so that it can guarantee a correct in- coming ftp data or IRC connection. nat unregistered_only yes|no Only alter outgoing packets with an unregistered source address. According to RFC 1918, unregistered source addresses are 10.0.0.0/8, 172.16.0.0/12 and 192.168.0.0/16. These commands are also discussed in the file README.nat which comes with the source distribution. [!]bg command The given command is executed in the background with the following words replaced: AUTHNAME This is replaced with the local authname value. See the "set authname" command below. COMPILATIONDATE This is replaced with the date on which ppp was com- piled. DNS0 & DNS1 These are replaced with the primary and secondary nameserver IP numbers. If nameservers are negoti- ated by IPCP, the values of these macros will change. ENDDISC This is replaced with the local endpoint discrimina- tor value. See the "set enddisc" command below. HISADDR This is replaced with the peers IP number. HISADDR6 This is replaced with the peers IPv6 number. INTERFACE This is replaced with the name of the interface that's in use. IPOCTETSIN This is replaced with the number of IP bytes re- ceived since the connection was established. IPOCTETSOUT This is replaced with the number of IP bytes sent since the connection was established. IPPACKETSIN This is replaced with the number of IP packets re- ceived since the connection was established. IPPACKETSOUT This is replaced with the number of IP packets sent since the connection was established. IPV6OCTETSIN This is replaced with the number of IPv6 bytes re- ceived since the connection was established. IPV6OCTETSOUT This is replaced with the number of IPv6 bytes sent since the connection was established. IPV6PACKETSIN This is replaced with the number of IPv6 packets re- ceived since the connection was established. IPV6PACKETSOUT This is replaced with the number of IPv6 packets sent since the connection was established. LABEL This is replaced with the last label name used. A label may be specified on the ppp command line, via the "load" or "dial" commands and in the ppp.secret file. MYADDR This is replaced with the IP number assigned to the local interface. MYADDR6 This is replaced with the IPv6 number assigned to the local interface. OCTETSIN This is replaced with the number of bytes received since the connection was established. OCTETSOUT This is replaced with the number of bytes sent since the connection was established. PACKETSIN This is replaced with the number of packets received since the connection was established. PACKETSOUT This is replaced with the number of packets sent since the connection was established. PEER_ENDDISC This is replaced with the value of the peers end- point discriminator. PROCESSID This is replaced with the current process id. SOCKNAME This is replaced with the name of the diagnostic socket. UPTIME This is replaced with the bundle uptime in HH:MM:SS format. USER This is replaced with the username that has been au- thenticated with PAP or CHAP. Normally, this vari- able is assigned only in -direct mode. This value is available irrespective of whether utmp logging is enabled. VERSION This is replaced with the current version number of ppp. These substitutions are also done by the "set proctitle", "ident" and "log" commands. If you wish to pause ppp while the command executes, use the "shell" command instead. clear physical|ipcp|ipv6 [current|overall|peak...] Clear the specified throughput values at either the "physical", "ipcp" or "ipv6cp" level. If "physical" is specified, context must be given (see the "link" command below). If no second argument is given, all values are cleared. clone name[,name]... Clone the specified link, creating one or more new links according to the name argument(s). This command must be used from the "link" com- mand below unless you've only got a single link (in which case that link becomes the default). Links may be removed using the "remove" command below. The default link name is "deflink". close [lcp|ccp[!]] If no arguments are given, the relevant protocol layers will be brought down and the link will be closed. If "lcp" is specified, the LCP layer is brought down, but ppp will not bring the link offline. It is subsequently possible to use "term" (see below) to talk to the peer machine if, for example, something like "slirp" is being used. If "ccp" is specified, only the relevant compression layer is closed. If the "!" is used, the compression layer will remain in the closed state, otherwise it will re-enter the STOPPED state, waiting for the peer to initiate further CCP negotiation. In any event, this command does not disconnect the user from ppp or exit ppp. See the "quit" command below. delete[!] dest This command deletes the route with the given dest IP address. If dest is specified as `ALL', all non-direct entries in the routing ta- ble for the current interface, and all `sticky route' entries are deleted. If dest is specified as `default', the default route is deleted. If the delete! command is used (note the trailing "!"), ppp will not complain if the route does not already exist. dial|call [label]... This command is the equivalent of "load label" followed by "open", and is provided for backwards compatibility. down [lcp|ccp] Bring the relevant layer down ungracefully, as if the underlying layer had become unavailable. It's not considered polite to use this command on a Finite State Machine that's in the OPEN state. If no arguments are supplied, the entire link is closed (or if no context is given, all links are terminated). If `lcp' is specified, the LCP layer is terminated but the device is not brought offline and the link is not closed. If `ccp' is specified, only the relevant com- pression layer(s) are terminated. help|? [command] Show a list of available commands. If command is specified, show the usage string for that command. ident [text...] Identify the link to the peer using text. If text is empty, link identification is disabled. It is possible to use any of the words described for the bg command above. Refer to the sendident command for details of when ppp identifies itself to the peer. iface command [args] This command is used to control the interface used by ppp. Command may be one of the following: iface add[!] addr[/bits] [peer] iface add[!] addr mask peer Add the given addr mask peer combination to the interface. In- stead of specifying mask, /bits can be used (with no space be- tween it and addr). If the given address already exists, the command fails unless the "!" is used - in which case the previous interface address entry is overwritten with the new one, allowing a change of netmask or peer address. If only addr is specified, bits defaults to "32" and peer de- faults to "255.255.255.255". This address (the broadcast ad- dress) is the only duplicate peer address that ppp allows. iface clear [INET | INET6] If this command is used while ppp is in the OPENED state or while in -auto mode, all addresses except for the NCP negotiated ad- dress are deleted from the interface. If ppp is not in the OPENED state and is not in -auto mode, all interface addresses are deleted. If the INET or INET6 arguments are used, only addresses for that address family are cleared. iface delete[!]|rm[!] addr This command deletes the given addr from the interface. If the "!" is used, no error is given if the address isn't currently as- signed to the interface (and no deletion takes place). iface show Shows the current state and current addresses for the interface. It is much the same as running "ifconfig INTERFACE". iface help [sub-command] This command, when invoked without sub-command, will show a list of possible "iface" sub-commands and a brief synopsis for each. When invoked with sub-command, only the synopsis for the given sub-command is shown. [data]link name[,name]... command [args] This command may prefix any other command if the user wishes to spec- ify which link the command should affect. This is only applicable after multiple links have been created in Multi-link mode using the "clone" command. Name specifies the name of an existing link. If name is a comma sep- arated list, command is executed on each link. If name is "*", command is executed on all links. load [label]... Load the given label(s) from the ppp.conf file. If label is not given, the default label is used. Unless the label section uses the "set mode", "open" or "dial" com- mands, ppp will not attempt to make an immediate connection. log word... Send the given word(s) to the log file with the prefix "LOG:". Word substitutions are done as explained under the "!bg" command above. open [lcp|ccp|ipcp] This is the opposite of the "close" command. All closed links are immediately brought up apart from second and subsequent demand-dial links - these will come up based on the "set autoload" command that has been used. If the "lcp" argument is used while the LCP layer is already open, LCP will be renegotiated. This allows various LCP options to be changed, after which "open lcp" can be used to put them into effect. After renegotiating LCP, any agreed authentication will also take place. If the "ccp" argument is used, the relevant compression layer is opened. Again, if it is already open, it will be renegotiated. If the "ipcp" argument is used, the link will be brought up as nor- mal, but if IPCP is already open, it will be renegotiated and the network interface will be reconfigured. It is probably not good practice to re-open the PPP state machines like this as it's possible that the peer will not behave correctly. It is however useful as a way of forcing the CCP or VJ dictionaries to be reset. passwd pass Specify the password required for access to the full ppp command set. This password is required when connecting to the diagnostic port (see the "set server" command). Pass is specified on the "set server" command line. The value of pass is not logged when command logging is active, instead, the literal string `********' is logged. quit|bye [all] If "quit" is executed from the controlling connection or from a com- mand file, ppp will exit after closing all connections. Otherwise, if the user is connected to a diagnostic socket, the connection is simply dropped. If the all argument is given, ppp will exit despite the source of the command after closing all existing connections. remove|rm This command removes the given link. It is only really useful in multi-link mode. A link must be in the CLOSED state before it is re- moved. rename|mv name This command renames the given link to name. It will fail if name is already used by another link. The default link name is `deflink'. Renaming it to `modem', `cuaa0' or `USR' may make the log file more readable. resolv command This command controls ppp's manipulation of the resolv.conf(5) file. When ppp starts up, it loads the contents of this file into memory and retains this image for future use. command is one of the follow- ing: readonly Treat /etc/resolv.conf as read only. If "dns" is enabled, ppp will still attempt to negotiate nameservers with the peer, making the results available via the DNS0 and DNS1 macros. This is the opposite of the "resolv writable" com- mand. reload Reload /etc/resolv.conf into memory. This may be necessary if for example a DHCP client overwrote /etc/resolv.conf. restore Replace /etc/resolv.conf with the version originally read at startup or with the last "resolv reload" command. This is sometimes a useful command to put in the /etc/ppp/ppp.linkdown file. rewrite Rewrite the /etc/resolv.conf file. This command will work even if the "resolv readonly" command has been used. It may be useful as a command in the /etc/ppp/ppp.linkup file if you wish to defer updating /etc/resolv.conf until after other commands have finished. writable Allow ppp to update /etc/resolv.conf if "dns" is enabled and ppp successfully negotiates a DNS. This is the oppo- site of the "resolv readonly" command. save This option is not (yet) implemented. sendident This command tells ppp to identify itself to the peer. The link must be in LCP state or higher. If no identity has been set (via the ident command), sendident will fail. When an identity has been set, ppp will automatically identify itself when it sends or receives a configure reject, when negotiation fails or when LCP reaches the opened state. Received identification packets are logged to the LCP log (see set log for details) and are never responded to. set[up] var value This option allows the setting of any of the following variables: set accmap hex-value ACCMap stands for Asynchronous Control Character Map. This is always negotiated with the peer, and defaults to a value of 00000000 in hex. This protocol is required to defeat hardware that depends on passing certain characters from end to end (such as XON/XOFF etc). For the XON/XOFF scenario, use "set accmap 000a0000". set [auth]key value This sets the authentication key (or password) used in client mode PAP or CHAP negotiation to the given value. It also speci- fies the password to be used in the dial or login scripts in place of the `\P' sequence, preventing the actual password from being logged. If command or chat logging is in effect, value is logged as `********' for security reasons. If the first character of value is an exclamation mark ("!"), ppp treats the remainder of the string as a program that must be exe- cuted to determine the "authname" and "authkey" values. If the "!" is doubled up (to "!!"), it is treated as a single literal "!", otherwise, ignoring the "!", value is parsed as a program to execute in the same was as the "!bg" command above, substituting special names in the same manner. Once executed, ppp will feed the program three lines of input, each terminated by a newline character: o The host name as sent in the CHAP challenge. o The challenge string as sent in the CHAP challenge. o The locally defined "authname". Two lines of output are expected: o The "authname" to be sent with the CHAP response. o The "authkey", which is encrypted with the challenge and re- quest id, the answer being sent in the CHAP response packet. When configuring ppp in this manner, it's expected that the host challenge is a series of ASCII digits or characters. An encryp- tion device or Secure ID card is usually required to calculate the secret appropriate for the given challenge. set authname id This sets the authentication id used in client mode PAP or CHAP negotiation. If used in -direct mode with CHAP enabled, id is used in the ini- tial authentication challenge and should normally be set to the local machine name. set autoload min-percent max-percent period These settings apply only in multi-link mode and default to zero, zero and five respectively. When more than one demand-dial (also known as -auto) mode link is available, only the first link is made active when ppp first reads data from the tun device. The next demand-dial link will be opened only when the current bundle throughput is at least max-percent percent of the total bundle bandwidth for period seconds. When the current bundle throughput decreases to min-percent percent or less of the total bundle bandwidth for period seconds, a demand-dial link will be brought down as long as it's not the last active link. Bundle throughput is measured as the maximum of inbound and out- bound traffic. The default values cause demand-dial links to simply come up one at a time. Certain devices cannot determine their physical bandwidth, so it is sometimes necessary to use the "set bandwidth" command (de- scribed below) to make "set autoload" work correctly. set bandwidth value This command sets the connection bandwidth in bits per second. value must be greater than zero. It is currently only used by the "set autoload" command above. set callback option... If no arguments are given, callback is disabled, otherwise, ppp will request (or in -direct mode, will accept) one of the given options. In client mode, if an option is NAK'd ppp will request a different option, until no options remain at which point ppp will terminate negotiations (unless "none" is one of the speci- fied option). In server mode, ppp will accept any of the given protocols - but the client must request one of them. If you wish callback to be optional, you must include none as an option. The options are as follows (in this order of preference): auth The callee is expected to decide the callback number based on authentication. If ppp is the callee, the num- ber should be specified as the fifth field of the peers entry in /etc/ppp/ppp.secret. cbcp Microsoft's callback control protocol is used. See "set cbcp" below. If you wish to negotiate cbcp in client mode but also wish to allow the server to request no callback at CBCP negotiation time, you must specify both cbcp and none as callback options. E.164 *|number[,number]... The caller specifies the number. If ppp is the callee, number should be either a comma separated list of allow- able numbers or a "*", meaning any number is permitted. If ppp is the caller, only a single number should be specified. Note, this option is very unsafe when used with a "*" as a malicious caller can tell ppp to call any (possibly in- ternational) number without first authenticating them- selves. none If the peer does not wish to do callback at all, ppp will accept the fact and continue without callback rather than terminating the connection. This is required (in addi- tion to one or more other callback options) if you wish callback to be optional. set cbcp [*|number[,number...] [delay [retry]]] If no arguments are given, CBCP (Microsoft's CallBack Control Protocol) is disabled - ie, configuring CBCP in the "set callback" command will result in ppp requesting no callback in the CBCP phase. Otherwise, ppp attempts to use the given phone number(s). In server mode (-direct), ppp will insist that the client uses one of these numbers, unless "*" is used in which case the client is expected to specify the number. In client mode, ppp will attempt to use one of the given numbers (whichever it finds to be agreeable with the peer), or if "*" is specified, ppp will expect the peer to specify the number. set cd [off|seconds[!]] Normally, ppp checks for the existence of carrier depending on the type of device that has been opened: Terminal Devices Carrier is checked one second after the login script is complete. If it's not set, ppp assumes that this is be- cause the device doesn't support carrier (which is true for most "laplink" NULL-modem cables), logs the fact and stops checking for carrier. As ptys don't support the TIOCMGET ioctl, the tty device will switch all carrier detection off when it detects that the device is a pty. ISDN (i4b) Devices Carrier is checked once per second for 6 seconds. If it's not set after the sixth second, the connection at- tempt is considered to have failed and the device is closed. Carrier is always required for i4b devices. PPPoE (netgraph) Devices Carrier is checked once per second for 5 seconds. If it's not set after the fifth second, the connection at- tempt is considered to have failed and the device is closed. Carrier is always required for PPPoE devices. All other device types don't support carrier. Setting a carrier value will result in a warning when the device is opened. Some modems take more than one second after connecting to assert the carrier signal. If this delay isn't increased, this will re- sult in ppp's inability to detect when the link is dropped, as ppp assumes that the device isn't asserting carrier. The "set cd" command overrides the default carrier behaviour. seconds specifies the maximum number of seconds that ppp should wait after the dial script has finished before deciding if car- rier is available or not. If "off" is specified, ppp will not check for carrier on the de- vice, otherwise ppp will not proceed to the login script until either carrier is detected or until seconds has elapsed, at which point ppp assumes that the device will not set carrier. If no arguments are given, carrier settings will go back to their default values. If seconds is followed immediately by an exclamation mark ("!"), ppp will require carrier. If carrier is not detected after seconds seconds, the link will be disconnected. set choked [timeout] This sets the number of seconds that ppp will keep a choked out- put queue before dropping all pending output packets. If timeout is less than or equal to zero or if timeout isn't specified, it is set to the default value of 120 seconds. A choked output queue occurs when ppp has read a certain number of packets from the local network for transmission, but cannot send the data due to link failure (the peer is busy etc.). ppp will not read packets indefinitely. Instead, it reads up to 30 packets (or 30 + nlinks * 2 packets in multi-link mode), then stops reading the network interface until either timeout seconds have passed or at least one packet has been sent. If timeout seconds pass, all pending output packets are dropped. set ctsrts|crtscts on|off This sets hardware flow control. Hardware flow control is on by default. set deflate out-winsize [in-winsize] This sets the DEFLATE algorithms default outgoing and incoming window sizes. Both out-winsize and in-winsize must be values be- tween 8 and 15. If in-winsize is specified, ppp will insist that this window size is used and will not accept any other values from the peer. set dns [primary [secondary]] This command specifies DNS overrides for the "accept dns" com- mand. Refer to the "accept" command description above for de- tails. This command does not affect the IP numbers requested us- ing "enable dns". set device|line value... This sets the device(s) to which ppp will talk to the given "value". All ISDN and serial device names are expected to begin with /dev/. ISDN devices are usually called i4brbchX and serial de- vices are usually called cuaXX. If "value" does not begin with /dev/, it must either begin with an exclamation mark ("!"), be of the format PPPoE:iface[:provider] (on netgraph(4) enabled systems), or be of the format host:port[/tcp|udp]. If it begins with an exclamation mark, the rest of the device name is treated as a program name, and that program is executed when the device is opened. Standard input, output and error are fed back to ppp and are read and written as if they were a regu- lar device. If a PPPoE:iface[:provider] specification is given, ppp will at- tempt to create a PPP over Ethernet connection using the given iface interface by using netgraph(4). If netgraph(4) is not available, ppp will attempt to load it using kldload(2). If this fails, an external program must be used such as the pppoe(8) pro- gram available under OpenBSD. The given provider is passed as the service name in the PPPoE Discovery Initiation (PADI) packet. If no provider is given, an empty value will be used. When a PPPoE connection is established, ppp will place the name of the Access Concentrator in the environment variable ACNAME. Refer to netgraph(4) and ng_pppoe(4) for further details. If a host:port[/tcp|udp] specification is given, ppp will attempt to connect to the given host on the given port. If a "/tcp" or "/udp" suffix is not provided, the default is "/tcp". Refer to the section on PPP OVER TCP and UDP above for further details. If multiple "values" are specified, ppp will attempt to open each one in turn until it succeeds or runs out of devices. set dial chat-script This specifies the chat script that will be used to dial the other side. See also the "set login" command below. Refer to chat(8) and to the example configuration files for details of the chat script format. It is possible to specify some special `values' in your chat script as follows: \c When used as the last character in a `send' string, this in- dicates that a newline should not be appended. \d When the chat script encounters this sequence, it delays two seconds. \p When the chat script encounters this sequence, it delays for one quarter of a second. \n This is replaced with a newline character. \r This is replaced with a carriage return character. \s This is replaced with a space character. \t This is replaced with a tab character. \T This is replaced by the current phone number (see "set phone" below). \P This is replaced by the current authkey value (see "set authkey" above). \U This is replaced by the current authname value (see "set authname" above). Note that two parsers will examine these escape sequences, so in order to have the `chat parser' see the escape character, it is necessary to escape it from the `command parser'. This means that in practice you should use two escapes, for example: set dial "... ATDT\\T CONNECT" It is also possible to execute external commands from the chat script. To do this, the first character of the expect or send string is an exclamation mark ("!"). If a literal exclamation mark is required, double it up to "!!" and it will be treated as a single literal "!". When the command is executed, standard in- put and standard output are directed to the open device (see the "set device" command), and standard error is read by ppp and sub- stituted as the expect or send string. If ppp is running in in- teractive mode, file descriptor 3 is attached to /dev/tty. For example (wrapped for readability): set login "TIMEOUT 5 \"\" \"\" login:--login: ppp \ word: ppp \"!sh \\-c \\\"echo \\-n label: >&2\\\"\" \ \"!/bin/echo in\" HELLO" would result in the following chat sequence (output using the `set log local chat' command before dialing): Dial attempt 1 of 1 dial OK! Chat: Expecting: Chat: Sending: Chat: Expecting: login:--login: Chat: Wait for (5): login: Chat: Sending: ppp Chat: Expecting: word: Chat: Wait for (5): word: Chat: Sending: ppp Chat: Expecting: !sh \-c "echo \-n label: >&2" Chat: Exec: sh -c "echo -n label: >&2" Chat: Wait for (5): !sh \-c "echo \-n label: >&2" --> label: Chat: Exec: /bin/echo in Chat: Sending: Chat: Expecting: HELLO Chat: Wait for (5): HELLO login OK! Note (again) the use of the escape character, allowing many lev- els of nesting. Here, there are four parsers at work. The first parses the original line, reading it as three arguments. The second parses the third argument, reading it as 11 arguments. At this point, it is important that the "-" signs are escaped, oth- erwise this parser will see them as constituting an expect-send- expect sequence. When the "!" character is seen, the execution parser reads the first command as three arguments, and then sh(1) itself expands the argument after the -c. As we wish to send the output back to the modem, in the first example we redirect our output to file descriptor 2 (stderr) so that ppp itself sends and logs it, and in the second example, we just output to stdout, which is attached directly to the modem. This, of course means that it is possible to execute an entirely external "chat" command rather than using the internal one. See chat(8) for a good alternative. The external command that is executed is subjected to the same special word expansions as the "!bg" command. set enddisc [label|IP|MAC|magic|psn value] This command sets our local endpoint discriminator. If set prior to LCP negotiation, and if no "disable enddisc" command has been used, ppp will send the information to the peer using the LCP endpoint discriminator option. The following discriminators may be set: label The current label is used. IP Our local IP number is used. As LCP is negotiated prior to IPCP, it is possible that the IPCP layer will subse- quently change this value. If it does, the endpoint dis- criminator stays at the old value unless manually reset. MAC This is similar to the IP option above, except that the MAC address associated with the local IP number is used. If the local IP number is not resident on any Ethernet interface, the command will fail. As the local IP number defaults to whatever the machine host name is, "set enddisc mac" is usually done prior to any "set ifaddr" commands. magic A 20 digit random number is used. Care should be taken when using magic numbers as restarting ppp or creating a link using a different ppp invocation will also use a different magic number and will therefore not be recog- nised by the peer as belonging to the same bundle. This makes it unsuitable for -direct connections. psn value The given value is used. Value should be set to an abso- lute public switched network number with the country code first. If no arguments are given, the endpoint discriminator is reset. set escape value... This option is similar to the "set accmap" option above. It al- lows the user to specify a set of characters that will be `escaped' as they travel across the link. set filter dial|alive|in|out rule-no permit|deny|clear|rule-no [!] [[host] src_addr[/width] [dst_addr[/width]]] [proto [src lt|eq|gt port] [dst lt|eq|gt port] [estab] [syn] [finrst] [timeout secs]] ppp supports four filter sets. The alive filter specifies pack- ets that keep the connection alive - resetting the idle timer. The dial filter specifies packets that cause ppp to dial when in -auto mode. The in filter specifies packets that are allowed to travel into the machine and the out filter specifies packets that are allowed out of the machine. Filtering is done prior to any IP alterations that might be done by the NAT engine on outgoing packets and after any IP alter- ations that might be done by the NAT engine on incoming packets. By default all empty filter sets allow all packets to pass. Rules are processed in order according to rule-no (unless skipped by specifying a rule number as the action). Up to 40 rules may be given for each set. If a packet doesn't match any of the rules in a given set, it is discarded. In the case of in and out filters, this means that the packet is dropped. In the case of alive filters it means that the packet will not reset the idle timer (even if the in/out filter has a "timeout" value) and in the case of dial filters it means that the packet will not trig- ger a dial. A packet failing to trigger a dial will be dropped rather than queued. Refer to the section on PACKET FILTERING above for further details. set hangup chat-script This specifies the chat script that will be used to reset the de- vice before it is closed. It should not normally be necessary, but can be used for devices that fail to reset themselves prop- erly on close. set help|? [command] This command gives a summary of available set commands, or if command is specified, the command usage is shown. set ifaddr [myaddr[/nn] [hisaddr[/nn] [netmask [triggeraddr]]]] This command specifies the IP addresses that will be used during IPCP negotiation. Addresses are specified using the format a.b.c.d/nn Where "a.b.c.d" is the preferred IP, but nn specifies how many bits of the address we will insist on. If /nn is omitted, it de- faults to "/32" unless the IP address is 0.0.0.0 in which case it defaults to "/0". If you wish to assign a dynamic IP number to the peer, hisaddr may also be specified as a range of IP numbers in the format IP[-IP][,IP[-IP]]... for example: set ifaddr 10.0.0.1 10.0.1.2-10.0.1.10,10.0.1.20 will only negotiate "10.0.0.1" as the local IP number, but may assign any of the given 10 IP numbers to the peer. If the peer requests one of these numbers, and that number is not already in use, ppp will grant the peers request. This is useful if the peer wants to re-establish a link using the same IP number as was previously allocated (thus maintaining any existing tcp or udp connections). If the peer requests an IP number that's either outside of this range or is already in use, ppp will suggest a random unused IP number from the range. If triggeraddr is specified, it is used in place of myaddr in the initial IPCP negotiation. However, only an address in the myaddr range will be accepted. This is useful when negotiating with some PPP implementations that will not assign an IP number unless their peer requests "0.0.0.0". It should be noted that in -auto mode, ppp will configure the in- terface immediately upon reading the "set ifaddr" line in the config file. In any other mode, these values are just used for IPCP negotiations, and the interface isn't configured until the IPCP layer is up. Note that the HISADDR argument may be overridden by the third field in the ppp.secret file once the client has authenticated itself (if PAP or CHAP are "enabled"). Refer to the AUTHENTICATING INCOMING CONNECTIONS section for details. In all cases, if the interface is already configured, ppp will try to maintain the interface IP numbers so that any existing bound sockets will remain valid. set ifqueue packets Set the maximum number of packets that ppp will read from the tunnel interface while data cannot be sent to any of the avail- able links. This queue limit is necessary to flow control outgo- ing data as the tunnel interface is likely to be far faster than the combined links available to ppp. If packets is set to a value less than the number of links, ppp will read up to that value regardless. This prevents any possi- ble latency problems. The default value for packets is "30". set ccpretry|ccpretries [timeout [reqtries [trmtries]]] set chapretry|chapretries [timeout [reqtries]] set ipcpretry|ipcpretries [timeout [reqtries [trmtries]]] set ipv6cpretry|ipv6cpretries [timeout [reqtries [trmtries]]] set lcpretry|lcpretries [timeout [reqtries [trmtries]]] set papretry|papretries [timeout [reqtries]] These commands set the number of seconds that ppp will wait be- fore resending Finite State Machine (FSM) Request packets. The default timeout for all FSMs is 3 seconds (which should suffice in most cases). If reqtries is specified, it tells ppp how many configuration re- quest attempts it should make while receiving no reply from the peer before giving up. The default is 5 attempts for CCP, LCP and IPCP and 3 attempts for PAP and CHAP. If trmtries is specified, it tells ppp how many terminate re- quests should be sent before giving up waiting for the peers re- sponse. The default is 3 attempts. Authentication protocols are not terminated and it is therefore invalid to specify trmtries for PAP or CHAP. In order to avoid negotiations with the peer that will never con- verge, ppp will only send at most 3 times the configured number of reqtries in any given negotiation session before giving up and closing that layer. set log [local] [+|-]value... This command allows the adjustment of the current log level. Re- fer to the Logging Facility section for further details. set login chat-script This chat-script compliments the dial-script. If both are speci- fied, the login script will be executed after the dial script. Escape sequences available in the dial script are also available here. set logout chat-script This specifies the chat script that will be used to logout before the hangup script is called. It should not normally be neces- sary. set lqrperiod frequency This command sets the frequency in seconds at which LQR or ECHO LQR packets are sent. The default is 30 seconds. You must also use the "enable lqr" command if you wish to send LQR requests to the peer. set mode interactive|auto|ddial|background This command allows you to change the `mode' of the specified link. This is normally only useful in multi-link mode, but may also be used in uni-link mode. It is not possible to change a link that is `direct' or `dedicated'. Note: If you issue the command "set mode auto", and have network address translation enabled, it may be useful to "enable iface-alias" afterwards. This will allow ppp to do the necessary address translations to enable the process that triggers the con- nection to connect once the link is up despite the peer assigning us a new (dynamic) IP address. set mppe [40|56|128|* [stateless|stateful|*]] This option selects the encryption parameters used when negotia- tion MPPE. MPPE can be disabled entirely with the "disable mppe" command. If no arguments are given, ppp will attempt to negoti- ate a stateful link with a 128 bit key, but will agree to what- ever the peer requests (including no encryption at all). If any arguments are given, ppp will insist on using MPPE and will close the link if it's rejected by the peer (Note; this be- haviour can be overridden by a configured RADIUS server). The first argument specifies the number of bits that ppp should insist on during negotiations and the second specifies whether ppp should insist on stateful or stateless mode. In stateless mode, the encryption dictionary is re-initialised with every packet according to an encryption key that is changed with every packet. In stateful mode, the encryption dictionary is re-ini- tialised every 256 packets or after the loss of any data and the key is changed every 256 packets. Stateless mode is less effi- cient but is better for unreliable transport layers. set mrru [value] Setting this option enables Multi-link PPP negotiations, also known as Multi-link Protocol or MP. There is no default MRRU (Maximum Reconstructed Receive Unit) value. If no argument is given, multi-link mode is disabled. set mru [max[imum]] [value] The default MRU (Maximum Receive Unit) is 1500. If it is in- creased, the other side *may* increase its MTU. In theory there is no point in decreasing the MRU to below the default as the PPP protocol says implementations *must* be able to accept packets of at least 1500 octets. If the "maximum" keyword is used, ppp will refuse to negotiate a higher value. The maximum MRU can be set to 2048 at most. Set- ting a maximum of less than 1500 violates the PPP rfc, but may sometimes be necessary. For example, PPPoE imposes a maximum of 1492 due to hardware limitations. If no argument is given, 1500 is assumed. A value must be given when "maximum" is specified. set mtu [max[imum]] [value] The default MTU is 1500. At negotiation time, ppp will accept whatever MRU the peer requests (assuming it's not less than 296 bytes or greater than the assigned maximum). If the MTU is set, ppp will not accept MRU values less than value. When negotia- tions are complete, the MTU is used when writing to the inter- face, even if the peer requested a higher value MRU. This can be useful for limiting your packet size (giving better bandwidth sharing at the expense of more header data). If the "maximum" keyword is used, ppp will refuse to negotiate a higher value. The maximum MTU can be set to 2048 at most. If no value is given, 1500, or whatever the peer asks for is used. A value must be given when "maximum" is specified. set nbns [x.x.x.x [y.y.y.y]] This option allows the setting of the Microsoft NetBIOS name server values to be returned at the peers request. If no values are given, ppp will reject any such requests. set openmode active|passive [delay] By default, openmode is always active with a one second delay. That is, ppp will always initiate LCP/IPCP/CCP negotiation one second after the line comes up. If you want to wait for the peer to initiate negotiations, you can use the value passive. If you want to initiate negotiations immediately or after more than one second, the appropriate delay may be specified here in seconds. set parity odd|even|none|mark This allows the line parity to be set. The default value is none. set phone telno[|backupnumber]...[:nextnumber]... This allows the specification of the phone number to be used in place of the \\T string in the dial and login chat scripts. Mul- tiple phone numbers may be given separated either by a pipe ("|") or a colon (":"). Numbers after the pipe are only dialed if the dial or login script for the previous number failed. Numbers after the colon are tried sequentially, irrespective of the reason the line was dropped. If multiple numbers are given, ppp will dial them according to these rules until a connection is made, retrying the maximum num- ber of times specified by "set redial" below. In -background mode, each number is attempted at most once. set [proc]title [value] The current process title as displayed by ps(1) is changed ac- cording to value. If value is not specified, the original process title is restored. All the word replacements done by the shell commands (see the "bg" command above) are done here too. Note, if USER is required in the process title, the "set proctitle" command must appear in ppp.linkup, as it is not known when the commands in ppp.conf are executed. set radius [config-file] This command enables RADIUS support (if it's compiled in). config-file refers to the radius client configuration file as de- scribed in radius.conf(5). If PAP, CHAP, MSCHAP or MSCHAPv2 are "enabled", ppp behaves as a Network Access Server and uses the configured RADIUS server to authenticate rather than authenticat- ing from the ppp.secret file or from the passwd database. If none of PAP, CHAP, MSCHAP or MSCHAPv2 are enabled, "set radius" will do nothing. ppp uses the following attributes from the RADIUS reply: RAD_FRAMED_IP_ADDRESS The peer IP address is set to the given value. RAD_FRAMED_IP_NETMASK The tun interface netmask is set to the given value. RAD_FRAMED_MTU If the given MTU is less than the peers MRU as agreed during LCP negotiation, *and* it is less that any config- ured MTU (see the "set mru" command), the tun interface MTU is set to the given value. RAD_FRAMED_COMPRESSION If the received compression type is "1", ppp will request VJ compression during IPCP negotiations despite any "disable vj" configuration command. RAD_FILTER_ID If this attribute is supplied, ppp will attempt to use it as an additional label to load from the ppp.linkup and ppp.linkdown files. The load will be attempted before (and in addition to) the normal label search. If the la- bel doesn't exist, no action is taken and ppp proceeds to the normal load using the current label. RAD_FRAMED_ROUTE The received string is expected to be in the format dest[/bits] gw [metrics]. Any specified metrics are ig- nored. MYADDR and HISADDR are understood as valid values for dest and gw, "default" can be used for dest to sep- cify the default route, and "0.0.0.0" is understood to be the same as "default" for dest and HISADDR for gw. For example, a returned value of "1.2.3.4/24 0.0.0.0 1 2 -1 3 400" would result in a routing table entry to the 1.2.3.0/24 network via HISADDR and a returned value of "0.0.0.0 0.0.0.0" or "default HISADDR" would result in a default route to HISADDR. All RADIUS routes are applied after any sticky routes are applied, making RADIUS routes override configured routes. This also applies for RADIUS routes that don't include the MYADDR or HISADDR keywords. RAD_SESSION_TIMEOUT If supplied, the client connection is closed after the given number of seconds. RAD_REPLY_MESSAGE If supplied, this message is passed back to the peer as the authentication SUCCESS text. RAD_MICROSOFT_MS_CHAP_ERROR If this RAD_VENDOR_MICROSOFT vendor specific attribute is supplied, it is passed back to the peer as the authenti- cation FAILURE text. RAD_MICROSOFT_MS_CHAP2_SUCCESS If this RAD_VENDOR_MICROSOFT vendor specific attribute is supplied and if MS-CHAPv2 authentication is being used, it is passed back to the peer as the authentication SUC- CESS text. RAD_MICROSOFT_MS_MPPE_ENCRYPTION_POLICY If this RAD_VENDOR_MICROSOFT vendor specific attribute is supplied and has a value of 2 (Required), ppp will insist that MPPE encryption is used (even if no "set mppe" con- figuration command has been given with arguments). If it is supplied with a value of 1 (Allowed), encryption is made optional (despite any "set mppe" configuration com- mands with arguments). RAD_MICROSOFT_MS_MPPE_ENCRYPTION_TYPES If this RAD_VENDOR_MICROSOFT vendor specific attribute is supplied, bits 1 and 2 are examined. If either or both are set, 40 bit and/or 128 bit (respectively) encryption options are set, overriding any given first argument to the "set mppe" command. Note, it is not currently possi- ble for the RADIUS server to specify 56 bit encryption. RAD_MICROSOFT_MS_MPPE_RECV_KEY If this RAD_VENDOR_MICROSOFT vendor specific attribute is supplied, it's value is used as the master key for de- cryption of incoming data. When clients are authenti- cated using MSCHAPv2, the RADIUS server MUST provide this attribute if inbound MPPE is to function. RAD_MICROSOFT_MS_MPPE_SEND_KEY If this RAD_VENDOR_MICROSOFT vendor specific attribute is supplied, it's value is used as the master key for en- cryption of outgoing data. When clients are authenti- cated using MSCHAPv2, the RADIUS server MUST provide this attribute if outbound MPPE is to function. Values received from the RADIUS server may be viewed using "show bundle". set reconnect timeout ntries Should the line drop unexpectedly (due to loss of CD or LQR fail- ure), a connection will be re-established after the given timeout. The line will be re-connected at most ntries times. Ntries defaults to zero. A value of random for timeout will re- sult in a variable pause, somewhere between 1 and 30 seconds. set recvpipe [value] This sets the routing table RECVPIPE value. The optimum value is just over twice the MTU value. If value is unspecified or zero, the default kernel controlled value is used. set redial secs[+inc[-max]][.next] [attempts] ppp can be instructed to attempt to redial attempts times. If more than one phone number is specified (see "set phone" above), a pause of next is taken before dialing each number. A pause of secs is taken before starting at the first number again. A lit- eral value of "random" may be used here in place of secs and next, causing a random delay of between 1 and 30 seconds. If inc is specified, its value is added onto secs each time ppp tries a new number. secs will only be incremented at most max times. max defaults to 10. Note, the secs delay will be effective, even after attempts has been exceeded, so an immediate manual dial may appear to have done nothing. If an immediate dial is required, a "!" should im- mediately follow the "open" keyword. See the "open" description above for further details. set sendpipe [value] This sets the routing table SENDPIPE value. The optimum value is just over twice the MTU value. If value is unspecified or zero, the default kernel controlled value is used. set server|socket TcpPort|LocalName|none|open|closed [password [mask]] This command tells ppp to listen on the given socket or `diagnostic port' for incoming command connections. The word "none" instructs ppp to close any existing socket and clear the socket configuration. The word "open" instructs ppp to attempt to re-open the port. The word "closed" instructs ppp to close the open port. If you wish to specify a local domain socket, LocalName must be specified as an absolute file name, otherwise it is assumed to be the name or number of a TCP port. You may specify the octal umask to be used with a local domain socket. Refer to umask(2) for umask details. Refer to services(5) for details of how to translate TCP port names. You must also specify the password that must be entered by the client (using the "passwd" variable above) when connecting to this socket. If the password is specified as an empty string, no password is required for connecting clients. When specifying a local domain socket, the first "%d" sequence found in the socket name will be replaced with the current inter- face unit number. This is useful when you wish to use the same profile for more than one connection. In a similar manner TCP sockets may be prefixed with the "+" character, in which case the current interface unit number is added to the port number. When using ppp with a server socket, the pppctl(8) command is the preferred mechanism of communications. Currently, telnet(1) can also be used, but link encryption may be implemented in the fu- ture, so telnet(1) should be avoided. Note; SIGUSR1 and SIGUSR2 interact with the diagnostic socket. set speed value This sets the speed of the serial device. If speed is specified as "sync", ppp treats the device as a synchronous device. Certain device types will know whether they should be specified as synchronous or asynchronous. These devices will override in- correct settings and log a warning to this effect. set stopped [LCPseconds [CCPseconds]] If this option is set, ppp will time out after the given FSM (Fi- nite State Machine) has been in the stopped state for the given number of "seconds". This option may be useful if the peer sends a terminate request, but never actually closes the connection de- spite our sending a terminate acknowledgement. This is also use- ful if you wish to "set openmode passive" and time out if the peer doesn't send a Configure Request within the given time. Use "set log +lcp +ccp" to make ppp log the appropriate state transi- tions. The default value is zero, where ppp doesn't time out in the stopped state. This value should not be set to less than the openmode delay (see "set openmode" above). set timeout idleseconds [mintimeout] This command allows the setting of the idle timer. Refer to the section titled SETTING THE IDLE TIMER for further details. If mintimeout is specified, ppp will never idle out before the link has been up for at least that number of seconds. set urgent [tcp|udp|none] [[+|-]port] ... This command controls the ports that ppp prioritizes when trans- mitting data. The default priority TCP ports are ports 21 (ftp control), 22 (ssh), 23 (telnet), 513 (login), 514 (shell), 543 (klogin) and 544 (kshell). There are no priority UDP ports by default. See services(5) for details. If neither "tcp" or "udp" are specified, "tcp" is assumed. If no ports are given, the priority port lists are cleared (al- though if "tcp" or "udp" is specified, only that list is cleared). If the first port argument is prefixed with a plus ("+") or a minus ("-"), the current list is adjusted, otherwise the list is reassigned. ports prefixed with a plus or not pre- fixed at all are added to the list and ports prefixed with a mi- nus are removed from the list. If "none" is specified, all priority port lists are disabled and even IPTOS_LOWDELAY packets are not prioritised. set vj slotcomp on|off This command tells ppp whether it should attempt to negotiate VJ slot compression. By default, slot compression is turned on. set vj slots nslots This command sets the initial number of slots that ppp will try to negotiate with the peer when VJ compression is enabled (see the `enable' command above). It defaults to a value of 16. Nslots must be between 4 and 16 inclusive. shell|! [command] If command is not specified a shell is invoked according to the SHELL environment variable. Otherwise, the given command is executed. Word replacement is done in the same way as for the "!bg" command as described above. Use of the ! character requires a following space as with any of the other commands. You should note that this command is executed in the foreground; ppp will not continue running until this process has ex- ited. Use the bg command if you wish processing to happen in the background. show var This command allows the user to examine the following: show bundle Show the current bundle settings. show ccp Show the current CCP compression statistics. show compress Show the current VJ compression statistics. show escape Show the current escape characters. show filter [name] List the current rules for the given filter. If name is not specified, all filters are shown. show hdlc Show the current HDLC statistics. show help|? Give a summary of available show commands. show iface Show the current interface information (the same as "iface show"). show ipcp Show the current IPCP statistics. show layers Show the protocol layers currently in use. show lcp Show the current LCP statistics. show [data]link Show high level link information. show links Show a list of available logical links. show log Show the current log values. show mem Show current memory statistics. show ncp Show the current NCP statistics. show physical Show low level link information. show mp Show Multi-link information. show proto Show current protocol totals. show route Show the current routing tables. show stopped Show the current stopped timeouts. show timer Show the active alarm timers. show version Show the current version number of ppp. term Go into terminal mode. Characters typed at the keyboard are sent to the device. Characters read from the device are displayed on the screen. When a remote PPP peer is detected, ppp automatically en- ables Packet Mode and goes back into command mode. MORE DETAILS o Read the example configuration files. They are a good source of in- formation. o Use "help", "nat ?", "enable ?", "set ?" and "show ?" to get online information about what's available. o The following URLs contain useful information: o http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/faq/ppp.html o http://www.FreeBSD.org/doc/handbook/userppp.html FILES ppp refers to four files: ppp.conf, ppp.linkup, ppp.linkdown and ppp.secret. These files are placed in the /etc/ppp directory. /etc/ppp/ppp.conf System default configuration file. /etc/ppp/ppp.secret An authorisation file for each system. /etc/ppp/ppp.linkup A file to check when ppp establishes a network level connection. /etc/ppp/ppp.linkdown A file to check when ppp closes a network level connection. /var/log/ppp.log Logging and debugging information file. Note, this name is specified in /etc/syslog.conf. See syslog.conf(5) for further details. /var/spool/lock/LCK..* tty port locking file. Refer to uucplock(3) for further details. /var/run/tunN.pid The process id (pid) of the ppp program connected to the tunN device, where `N' is the number of the device. /var/run/ttyXX.if The tun interface used by this port. Again, this file is only cre- ated in -background, -auto and -ddial modes. /etc/services Get port number if port number is using service name. /var/run/ppp-authname-class-value In multi-link mode, local domain sockets are created using the peer authentication name (`authname'), the peer endpoint discriminator class (`class') and the peer endpoint discriminator value (`value'). As the endpoint discriminator value may be a binary value, it is turned to HEX to determine the actual file name. This socket is used to pass links between different instances of ppp. SEE ALSO at(1), ftp(1), gzip(1), hostname(1), login(1), tcpdump(1), telnet(1), kldload(2), libalias(3), libradius(3), syslog(3), uucplock(3), netgraph(4), ng_pppoe(4), crontab(5), group(5), passwd(5), protocols(5), radius.conf(5), resolv.conf(5), syslog.conf(5), adduser(8), chat(8), getty(8), inetd(8), init(8), isdn(8), named(8), ping(8), pppctl(8), pppd(8), pppoe(8), route(8), sshd(8), syslogd(8), traceroute(8), vipw(8) HISTORY This program was originally written by Toshiharu OHNO <tony-o@iij.ad.jp>, and was submitted to FreeBSD 2.0.5 by Atsushi Murai <amurai@spec.co.jp>. It was substantially modified during 1997 by Brian Somers <brian@Awfulhak.org>, and was ported to OpenBSD in November that year (just after the 2.2 release). Most of the code was rewritten by Brian Somers in early 1998 when multi- link ppp support was added. BSD September 20, 1995 BSD
NAME | SYNOPSIS | DESCRIPTION | Major Features | PERMISSIONS | GETTING STARTED | MANUAL DIALING | AUTOMATIC DIALING | BACKGROUND DIALING | DIAL ON DEMAND | RECEIVING INCOMING PPP CONNECTIONS (Method 1) | RECEIVING INCOMING PPP CONNECTIONS (Method 2) | AUTHENTICATING INCOMING CONNECTIONS | PPP OVER TCP and UDP (a.k.a Tunnelling) | NETWORK ADDRESS TRANSLATION (PACKET ALIASING) | PACKET FILTERING | SETTING THE IDLE TIMER | PREDICTOR-1 and DEFLATE COMPRESSION | CONTROLLING IP ADDRESS | CONNECTING WITH YOUR INTERNET SERVICE PROVIDER | LOGGING FACILITY | SIGNAL HANDLING | MULTI-LINK PPP | PPP COMMAND LIST | MORE DETAILS | FILES | SEE ALSO | HISTORY
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=ppp&sektion=8&manpath=FreeBSD+4.7-RELEASE>