FreeBSD Manual Pages
SETKEY(8) BSD System Manager's Manual SETKEY(8) NAME setkey -- manually manipulate the IPsec SA/SP database SYNOPSIS setkey [-v] -c setkey [-v] -f filename setkey [-Pgltv] -D setkey [-Pv] -F setkey [-h] -x DESCRIPTION The setkey utility adds, updates, dumps, or flushes Security Association Database (SAD) entries as well as Security Policy Database (SPD) entries in the kernel. The setkey utility takes a series of operations from the standard input (if invoked with -c) or the file named filename (if invoked with -f filename). -D Dump the SAD entries. If with -P, the SPD entries are dumped. -F Flush the SAD entries. If with -P, the SPD entries are flushed. -g Only SPD entries with global scope are dumped with -D and -P flags. -t Only SPD entries with ifnet scope are dumped with -D and -P flags. Such SPD entries are linked to the corresponding if_ipsec(4) virtual tunneling interface. -h Add hexadecimal dump on -x mode. -l Loop forever with short output on -D. -v Be verbose. The program will dump messages exchanged on PF_KEY socket, including messages sent from other processes to the ker- nel. -x Loop forever and dump all the messages transmitted to PF_KEY socket. -xx makes each timestamp unformatted. Configuration syntax With -c or -f on the command line, setkey accepts the following configu- ration syntax. Lines starting with hash signs (`#') are treated as com- ment lines. add [-46n] src dst protocol spi [extensions] algorithm ... ; Add an SAD entry. add can fail with multiple reasons, including when the key length does not match the specified algorithm. get [-46n] src dst protocol spi ; Show an SAD entry. delete [-46n] src dst protocol spi ; Remove an SAD entry. deleteall [-46n] src dst protocol ; Remove all SAD entries that match the specification. flush [protocol] ; Clear all SAD entries matched by the options. -F on the command line achieves the same functionality. dump [protocol] ; Dumps all SAD entries matched by the options. -D on the command line achieves the same functionality. spdadd [-46n] src_range dst_range upperspec policy ; Add an SPD entry. spddelete [-46n] src_range dst_range upperspec -P direction ; Delete an SPD entry. spdflush ; Clear all SPD entries. -FP on the command line achieves the same functionality. spddump ; Dumps all SPD entries. -DP on the command line achieves the same functionality. Meta-arguments are as follows: src dst Source/destination of the secure communication is specified as IPv4/v6 address. The setkey utility can resolve a FQDN into nu- meric addresses. If the FQDN resolves into multiple addresses, setkey will install multiple SAD/SPD entries into the kernel by trying all possible combinations. -4, -6 and -n restricts the address resolution of FQDN in certain ways. -4 and -6 restrict results into IPv4/v6 addresses only, respectively. -n avoids FQDN resolution and requires addresses to be numeric addresses. protocol protocol is one of following: esp ESP based on rfc2406 esp-old ESP based on rfc1827 ah AH based on rfc2402 ah-old AH based on rfc1826 ipcomp IPComp tcp TCP-MD5 based on rfc2385 spi Security Parameter Index (SPI) for the SAD and the SPD. spi must be a decimal number, or a hexadecimal number with `0x' prefix. SPI values between 0 and 255 are reserved for future use by IANA and they cannot be used. extensions take some of the following: -m mode Specify a security protocol mode for use. mode is one of following: transport, tunnel or any. The de- fault value is any. -r size Specify the bitmap size in octets of the anti-replay window. size is a 32-bit unsigned integer, and its value is one eighth of the anti-replay window size in packets. If size is zero or not specified, an anti- replay check does not take place. -u id Specify the identifier of the policy entry in SPD. See policy. -f pad_option defines the content of the ESP padding. pad_option is one of following: zero-pad All of the padding are zero. random-pad A series of randomized values are set. seq-pad A series of sequential increasing numbers started from 1 are set. -f nocyclic-seq Do not allow cyclic sequence number. -lh time -ls time Specify hard/soft life time duration of the SA. algorithm -E ealgo key Specify an encryption algorithm ealgo for ESP. -E ealgo key -A aalgo key Specify a encryption algorithm ealgo, as well as a payload authentication algorithm aalgo, for ESP. -A aalgo key Specify an authentication algorithm for AH. -C calgo [-R] Specify a compression algorithm for IPComp. If -R is specified, the spi field value will be used as the IPComp CPI (compression parameter index) on wire as is. If -R is not specified, the kernel will use well-known CPI on wire, and spi field will be used only as an index for kernel internal usage. key must be double-quoted character string, or a series of hexa- decimal digits preceded by `0x'. Possible values for ealgo, aalgo and calgo are specified in sepa- rate section. src_range dst_range These are selections of the secure communication specified as IPv4/v6 address or IPv4/v6 address range, and it may accompany TCP/UDP port specification. This takes the following form: address address/prefixlen address[port] address/prefixlen[port] prefixlen and port must be a decimal number. The square brackets around port are necessary and are not manpage metacharacters. For FQDN resolution, the rules applicable to src and dst apply here as well. upperspec The upper layer protocol to be used. You can use one of the words in /etc/protocols as upperspec, as well as icmp6, ip4, or any. The word any stands for "any protocol". The protocol num- ber may also be used to specify the upperspec. A type and code related to ICMPv6 may also be specified as an upperspec. The type is specified first, followed by a comma and then the rele- vant code. The specification must be placed after icmp6. The kernel considers a zero to be a wildcard but cannot distinguish between a wildcard and an ICMPv6 type which is zero. The follow- ing example shows a policy where IPSec is not required for in- bound Neighbor Solicitations: spdadd ::/0 ::/0 icmp6 135,0 -P in none; NOTE: upperspec does not work in the forwarding case at this mo- ment, as it requires extra reassembly at forwarding node, which is not implemented at this moment. Although there are many pro- tocols in /etc/protocols, protocols other than TCP, UDP and ICMP may not be suitable to use with IPsec. policy policy is expressed in one of the following three formats: -P direction discard -P direction none -P direction ipsec protocol/mode/src-dst/level [...] The direction of a policy must be specified as one of: out, in, discard, none, or ipsec. The discard direction means that pack- ets matching the supplied indices will be discarded while none means that IPsec operations will not take place on the packet and ipsec means that IPsec operation will take place onto the packet. The protocol/mode/src-dst/level statement gives the rule for how to process the packet. The protocol is specified as ah, esp or ipcomp. The mode is either transport or tunnel. If mode is tunnel, you must specify the end-point addresses of the SA as src and dst with a dash, `-', between the addresses. If mode is transport, both src and dst can be omitted. The level is one of the following: default, use, require or unique. If the SA is not available in every level, the kernel will request the SA from the key exchange daemon. A value of default tells the kernel to use the system wide default protocol e.g., the one from the esp_trans_deflev sysctl variable, when the kernel processes the packet. A value of use means that the kernel will use an SA if it is available, otherwise the kernel will pass the packet as it would normally. A value of require means that an SA is required whenever the kernel sends a packet matched that matches the pol- icy. The unique level is the same as require but, in addition, it allows the policy to bind with the unique out-bound SA. For example, if you specify the policy level unique, racoon(8) will configure the SA for the policy. If you configure the SA by man- ual keying for that policy, you can put the decimal number as the policy identifier after unique separated by colon `:' as in the following example: unique:number. In order to bind this policy to the SA, number must be between 1 and 32767, which corresponds to extensions -u of manual SA configuration. When you want to use an SA bundle, you can define multiple rules. For example, if an IP header was followed by an AH header fol- lowed by an ESP header followed by an upper layer protocol header, the rule would be: esp/transport//require ah/transport//require; The rule order is very important. Note that "discard" and "none" are not in the syntax described in ipsec_set_policy(3). There are small, but important, differences in the syntax. See ipsec_set_policy(3) for details. ALGORITHMS The following list shows the supported algorithms. The protocol and algorithm are almost completely orthogonal. The following list of au- thentication algorithms can be used as aalgo in the -A aalgo of the protocol parameter: algorithm keylen (bits) comment hmac-md5 128 ah: rfc2403 128 ah-old: rfc2085 hmac-sha1 160 ah: rfc2404 160 ah-old: 128bit ICV (no document) keyed-md5 128 ah: 96bit ICV (no document) 128 ah-old: rfc1828 keyed-sha1 160 ah: 96bit ICV (no document) 160 ah-old: 128bit ICV (no document) null 0 to 2048 for debugging hmac-sha2-256 256 ah: 128bit ICV (RFC4868) 256 ah-old: 128bit ICV (no document) hmac-sha2-384 384 ah: 192bit ICV (RFC4868) 384 ah-old: 128bit ICV (no document) hmac-sha2-512 512 ah: 256bit ICV (RFC4868) 512 ah-old: 128bit ICV (no document) hmac-ripemd160 160 ah: 96bit ICV (RFC2857) ah-old: 128bit ICV (no document) aes-xcbc-mac 128 ah: 96bit ICV (RFC3566) 128 ah-old: 128bit ICV (no document) tcp-md5 8 to 640 tcp: rfc2385 The following is the list of encryption algorithms that can be used as the ealgo in the -E ealgo of the protocol parameter: algorithm keylen (bits) comment des-cbc 64 esp-old: rfc1829, esp: rfc2405 3des-cbc 192 rfc2451 null 0 to 2048 rfc2410 blowfish-cbc 40 to 448 rfc2451 cast128-cbc 40 to 128 rfc2451 des-deriv 64 ipsec-ciph-des-derived-01 rijndael-cbc 128/192/256 rfc3602 aes-ctr 160/224/288 draft-ietf-ipsec-ciph-aes-ctr-03 aes-gcm-16 160/224/288 rfc4106 camellia-cbc 128/192/256 rfc4312 Note that the first 128/192/256 bits of a key for aes-ctr or aes-gcm-16 will be used as AES key, and remaining 32 bits will be used as nonce. The following are the list of compression algorithms that can be used as the calgo in the -C calgo of the protocol parameter: algorithm comment deflate rfc2394 EXIT STATUS The setkey utility exits 0 on success, and >0 if an error occurs. EXAMPLES Add an ESP SA between two IPv6 addresses using the des-cbc encryption al- gorithm. add 3ffe:501:4819::1 3ffe:501:481d::1 esp 123457 -E des-cbc 0x3ffe05014819ffff ; Add an authentication SA between two FQDN specified hosts: add -6 myhost.example.com yourhost.example.com ah 123456 -A hmac-sha1 "AH SA configuration!" ; Use both ESP and AH between two numerically specified hosts: add 10.0.11.41 10.0.11.33 esp 0x10001 -E des-cbc 0x3ffe05014819ffff -A hmac-md5 "authentication!!" ; Get the SA information associated with first example above: get 3ffe:501:4819::1 3ffe:501:481d::1 ah 123456 ; Flush all entries from the database: flush ; Dump the ESP entries from the database: dump esp ; Add a security policy between two networks that uses ESP in tunnel mode: spdadd 10.0.11.41/32[21] 10.0.11.33/32[any] any -P out ipsec esp/tunnel/192.168.0.1-192.168.1.2/require ; Use TCP MD5 between two numerically specified hosts: add 10.1.10.34 10.1.10.36 tcp 0x1000 -A tcp-md5 "TCP-MD5 BGP secret" ; add 10.1.10.36 10.1.10.34 tcp 0x1001 -A tcp-md5 "TCP-MD5 BGP secret" ; SEE ALSO ipsec_set_policy(3), if_ipsec(4), racoon(8), sysctl(8) Changed manual key configuration for IPsec, http://www.kame.net/newsletter/19991007/, October 1999. HISTORY The setkey utility first appeared in WIDE Hydrangea IPv6 protocol stack kit. The utility was completely re-designed in June 1998. It first ap- peared in FreeBSD 4.0. BUGS The setkey utility should report and handle syntax errors better. For IPsec gateway configuration, src_range and dst_range with TCP/UDP port number do not work, as the gateway does not reassemble packets (can- not inspect upper-layer headers). BSD April 9, 2017 BSD
NAME | SYNOPSIS | DESCRIPTION | ALGORITHMS | EXIT STATUS | EXAMPLES | SEE ALSO | HISTORY | BUGS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=setkey&sektion=8&manpath=FreeBSD+11.1-RELEASE>