FreeBSD Manual Pages
SFXGE(4) amd64 Kernel Interfaces Manual SFXGE(4) NAME sfxge -- Solarflare 10Gb Ethernet adapter driver SYNOPSIS To compile this driver into the kernel, place the following lines in your kernel configuration file: device sfxge To load the driver as a module at boot time, place the following line in loader.conf(5): sfxge_load="YES" DESCRIPTION The sfxge driver provides support for 10Gb Ethernet adapters based on So- larflare SFC9000 and XtremeScale X2 family controllers. The driver sup- ports jumbo frames, transmit/receive checksum offload, TCP Segmentation Of- fload (TSO), Large Receive Offload (LRO), VLAN checksum offload, VLAN TSO, and Receive Side Scaling (RSS) using MSI-X interrupts. The driver allocates 1 receive queue, transmit queue, event queue and IRQ per CPU up to a maximum of 64. IRQ affinities should be spread out using cpuset(1). Interrupt moderation may be controlled through the sysctl dev.sfxge.%d.int_mod (units are microseconds). For more information on configuring this device, see ifconfig(8). A large number of MAC, PHY and data path statistics are available under the sysctl dev.sfxge.%d.stats. The adapter's VPD fields including its serial number are available under the sysctl dev.sfxge.%d.vpd. HARDWARE The sfxge driver supports all 10Gb Ethernet adapters based on Solarflare SFC9000 family controllers. LOADER TUNABLES Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5). Actual values can be obtained using sysctl(8). hw.sfxge.rx_ring The maximum number of descriptors in a receive queue ring. Sup- ported values are: 512, 1024, 2048 and 4096. hw.sfxge.tx_ring The maximum number of descriptors in a transmit queue ring. Sup- ported values are: 512, 1024, 2048 and 4096. hw.sfxge.tx_dpl_get_max The maximum length of the deferred packet "get-list" for queued transmit packets (TCP and non-TCP), used only if the transmit queue lock can be acquired. If a packet is dropped, the tx_get_overflow counter is incremented and the local sender receives ENOBUFS. The value must be greater than 0. hw.sfxge.tx_dpl_get_non_tcp_max The maximum number of non-TCP packets in the deferred packet "get-list" , used only if the transmit queue lock can be acquired. If a packet is dropped, the tx_get_non_tcp_overflow counter is in- cremented and the local sender receives ENOBUFS. The value must be greater than 0. hw.sfxge.tx_dpl_put_max The maximum length of the deferred packet "put-list" for queued transmit packets, used if the transmit queue lock cannot be ac- quired. If a packet is dropped, the tx_put_overflow counter is in- cremented and the local sender receives ENOBUFS. The value must be greater than or equal to 0. hw.sfxge.tso_fw_assisted Bitmask to enable/disable usage of FW-assisted TSO version if sup- ported by NIC firmware. FATSOv1 (bit 0) and FATSOv2 (bit 1) are supported. All enabled by default. hw.sfxge.N.max_rss_channels The maximum number of allocated RSS channels for the Nth adapter. If set to 0 or unset, the number of channels is determined by the number of CPU cores. hw.sfxge.lro.table_size Size of the LRO hash table. Must be a power of 2. A larger table means we can accelerate a larger number of streams. hw.sfxge.lro.chain_max The maximum length of a hash chain. If chains get too long then the lookup time increases and may exceed the benefit of LRO. hw.sfxge.lro.idle_ticks The maximum time (in ticks) that a connection can be idle before it's LRO state is discarded. hw.sfxge.lro.slow_start_packets Number of packets with payload that must arrive in-order before a connection is eligible for LRO. The idea is we should avoid coa- lescing segments when the sender is in slow-start because reducing the ACK rate can damage performance. hw.sfxge.lro.loss_packets Number of packets with payload that must arrive in-order following loss before a connection is eligible for LRO. The idea is we should avoid coalescing segments when the sender is recovering from loss, because reducing the ACK rate can damage performance. hw.sfxge.mcdi_logging Enable logging of MCDI protocol messages (only available if en- abled at compile-time). hw.sfxge.N.mcdi_logging Enable or disable logging of MCDI protocol messages on a per-port basis. The default for each port will be the value of hw.sfxge.mcdi_logging. The logging may also be enabled or disabled after the driver is loaded using the sysctl dev.sfxge.%d.mcdi_logging. hw.sfxge.stats_update_period_ms Period in milliseconds to refresh interface statistics from hard- ware. The accepted range is 0 to 65535, the default is 1000 (1 second). Use zero value to disable periodic statistics update. Supported on SFN8xxx series adapters with firmware v6.2.1.1033 and later and SFN5xxx, SFN6xxx and XtremeScale X2xxx series adapters. SFN7xxx series adapters and sfN8xxx series with earlier firmware use a fixed 1000 milliseconds statistics update period. The period may also be changed after the driver is loaded using the sysctl dev.sfxge.%d.stats_update_period_ms. SUPPORT For general information and support, go to the Solarflare support website at: https://support.solarflare.com. SEE ALSO cpuset(1), arp(4), netintro(4), ng_ether(4), vlan(4), ifconfig(8) AUTHORS The sfxge driver was written by Philip Paeps and Solarflare Communications, Inc. FreeBSD ports 15.quarterly February 22, 2015 SFXGE(4)
NAME | SYNOPSIS | DESCRIPTION | HARDWARE | LOADER TUNABLES | SUPPORT | SEE ALSO | AUTHORS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=sfxge&manpath=FreeBSD+15.1-RELEASE+and+Ports.quarterly>