FreeBSD Manual Pages
TBL(7) Miscellaneous Information Manual TBL(7) NAME tbl -- tbl language reference for mandoc DESCRIPTION The tbl language formats tables. It is used within mdoc(7) and man(7) pages. This manual describes the subset of the tbl language accepted by the mandoc(1) utility. Each table is started with a roff(7) TS macro, consist of at most one line of "Options", one or more "Layout" lines, one or more "Data" lines, and ends with a TE macro. All input must be 7-bit ASCII. Options If the first input line of a table ends with a semicolon, it contains case-insensitive options separated by spaces, tabs, or commas. Other- wise, it is interpreted as the first "Layout" line. The following options are available. Some of them require arguments enclosed in parentheses: allbox Draw a single-line box around each table cell. box Draw a single-line box around the table. For GNU compatibil- ity, this may also be invoked with frame. center Center the table instead of left-adjusting it. For GNU compat- ibility, this may also be invoked with centre. decimalpoint Use the single-character argument as the decimal point with the n layout key. This is a GNU extension. delim Use the two characters of the argument as eqn(7) delimiters. Currently unsupported. doublebox Draw a double-line box around the table. For GNU compatibil- ity, this may also be invoked with doubleframe. expand Increase the width of the table to the current line length. Currently ignored. linesize Draw lines with the point size given by the unsigned integer argument. Currently ignored. nokeep Allow page breaks within the table. This is a GNU extension and currently ignored. nospaces Ignore leading and trailing spaces in data cells. This is a GNU extension. nowarn Suppress warnings about tables exceeding the current line length. This is a GNU extension and currently ignored. tab Use the single-character argument as a delimiter between data cells. By default, the horizontal tabulator character is used. Layout The table layout follows an "Options" line or a roff(7) TS or T& macro. Each layout line specifies how one line of "Data" is formatted. The last layout line ends with a full stop. It also applies to all remain- ing data lines. Multiple layout lines can be joined by commas on a single physical input line. Each layout line consists of one or more layout cell specifications, optionally separated by whitespace. The following case-insensitive key characters start a new cell specification: c Center the string in this cell. r Right-justify the string in this cell. l Left-justify the string in this cell. n Justify a number around its last decimal point. If no decimal point is found in the number, it is assumed to trail the number. s Horizontally span columns from the last non-s layout cell. It is an error if a column span follows a _ or = cell, or comes first on a layout line. The combined cell as a whole consumes only one cell of the corresponding data line. a Left-justify a string and pad with one space. ^ Vertically span rows from the last non-^ layout cell. It is an er- ror to invoke a vertical span on the first layout line. Unlike a horizontal span, a vertical span consumes a data cell and discards the content. _ Draw a single horizontal line in this cell. This consumes a data cell and discards the content. It may also be invoked with -. = Draw a double horizontal line in this cell. This consumes a data cell and discards the content. Each cell key may be followed by zero or more of the following case-in- sensitive modifiers: b Use a bold font for the contents of this cell. d Move content down to the last row of this vertical span. Currently ignored. e Make this column wider to match the maximum width of any other col- umn also having the e modifier. f The next one or two characters select the font to use for this cell. One-character font names must be followed by a blank or pe- riod. See the roff(7) manual for supported font names. i Use an italic font for the contents of this cell. m Specify a cell start macro. This is a GNU extension and currently unsupported. p Set the point size to the following unsigned argument, or change it by the following signed argument. Currently ignored. v Set the vertical line spacing to the following unsigned argument, or change it by the following signed argument. Currently ignored. t Do not vertically center content in this vertical span, leave it in the top row. Currently ignored. u Move cell content up by half a table row. Currently ignored. w Specify a minimum column width. x After determining the width of all other columns, distribute the rest of the line length among all columns having the x modifier. z Do not use this cell for determining the width of this column. | Draw a single vertical line to the right of this cell. || Draw a double vertical line to the right of this cell. If a modifier consists of decimal digits, it specifies a minimum spac- ing in units of n between this column and the next column to the right. The default is 3. If there is a vertical line, it is drawn inside the spacing. Data The data section follows the last "Layout" line. Each data line con- sists of one or more data cells, delimited by tab characters. If a data cell contains only the two bytes `\^', the cell above spans to this row, as if the layout specification of this cell were ^. If a data cell contains only the single character `_' or `=', a single or double horizontal line is drawn across the cell, joining its neigh- bours. If a data cell contains only the two character sequence `\_' or `\=', a single or double horizontal line is drawn inside the cell, not joining its neighbours. If a data line contains nothing but the single character `_' or `=', a horizontal line across the whole table is in- serted without consuming a layout row. In place of any data cell, a text block can be used. It starts with T{ at the end of a physical input line. Input line breaks inside the text block neither end the text block nor its data cell. It only ends if T} occurs at the beginning of a physical input line and is followed by an end-of-cell indicator. If the T} is followed by the end of the physi- cal input line, the text block, the data cell, and the data line ends at this point. If the T} is followed by the tab character, only the text block and the data cell end, but the data line continues with the data cell following the tab character. If T} is followed by any other character, it does not end the text block, which instead continues to the following physical input line. EXAMPLES String justification and font selection: .TS rb c lb r ci l. r center l ri ce le right c left .TE r center l ri ce le right c left Some ports in OpenBSD 6.1 to show number alignment and line drawing: .TS box tab(:); r| l r n. software:version _ AFL:2.39b Mutt:1.8.0 Ruby:1.8.7.374 TeX Live:2015 .TE +----------+-----------+ | software | version | +----------+-----------+ | AFL 2.39b | | Mutt 1.8.0 | | Ruby 1.8.7.374 | | TeX Live 2015 | +----------------------+ Spans and skipping width calculations: .TS box tab(:); lz s | rt lt| cb| ^ ^ | rz s. left:r l:center: :right .TE +------------+---+ | left | r | | l | center | | | | right | +---+------------+ Text blocks, specifying spacings and specifying and equalizing column widths, putting lines into individual cells, and overriding allbox: .TS allbox tab(:); le le||7 lw10. The fourth line:_:line 1 of this column:=:line 2 determines:_:line 3 the column width.:T{ This text is too wide to fit into a column of width 17. T}:line 4 T{ No break here. T}::line 5 .TE +---------------------+-----------------------++-------------+ | The fourth line +-----------------------+| line 1 | +---------------------+-----------------------++-------------+ | of this column +-----------------------+| line 2 | +---------------------+-----------------------++-------------+ | determines | -------------------- || line 3 | +---------------------+-----------------------++-------------+ | the column width. | This text is too || line 4 | | | wide to fit into a || | | | column of width 17. || | +---------------------+-----------------------++-------------+ | No break here. | || line 5 | +---------------------+-----------------------++-------------+ These examples were constructed to demonstrate many tbl features in a compact way. In real manual pages, keep tables as simple as possible. They usually look better, are less fragile, and are more portable. COMPATIBILITY The mandoc(1) implementation of tbl doesn't support mdoc(7) and man(7) macros and eqn(7) equations inside tables. SEE ALSO mandoc(1), man(7), mandoc_char(7), mdoc(7), roff(7) M. E. Lesk, Tbl -- A Program to Format Tables, June 11, 1976. HISTORY The tbl utility, a preprocessor for troff, was originally written by M. E. Lesk at Bell Labs in 1975. The GNU reimplementation of tbl, part of the groff package, was released in 1990 by James Clark. A standalone tbl implementation was written by Kristaps Dzonsons in 2010. This formed the basis of the implementation that first appeared in OpenBSD 4.9 as a part of the mandoc(1) utility. AUTHORS This tbl reference was written by Kristaps Dzonsons <kristaps@bsd.lv> and Ingo Schwarze <schwarze@openbsd.org>. BUGS In -T utf8 output mode, heavy lines are drawn instead of double lines. This cannot be improved because the Unicode standard only provides an incomplete set of box drawing characters with double lines, whereas it provides a full set of box drawing characters with heavy lines. It is unlikely this can be improved in the future because the box drawing characters are already marked in Unicode as characters intended only for backward compatibility with legacy systems, and their use is not encouraged. So it seems unlikely that the missing ones might get added in the future. FreeBSD 13.2 September 18, 2021 TBL(7)
NAME | DESCRIPTION | EXAMPLES | COMPATIBILITY | SEE ALSO | HISTORY | AUTHORS | BUGS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=tbl&sektion=7&manpath=FreeBSD+14.3-RELEASE+and+Ports>