FreeBSD Manual Pages
TR(1) General Commands Manual TR(1) NAME tr -- translate characters SYNOPSIS tr [-Ccsu] string1 string2 tr [-Ccu] -d string1 tr [-Ccu] -s string1 tr [-Ccu] -ds string1 string2 DESCRIPTION The tr utility copies the standard input to the standard output with substitution or deletion of selected characters. The following options are available: -C Complement the set of characters in string1, that is "-C ab" includes every character except for `a' and `b'. -c Same as -C but complement the set of values in string1. -d Delete characters in string1 from the input. -s Squeeze multiple occurrences of the characters listed in the last operand (either string1 or string2) in the input into a single instance of the character. This occurs after all dele- tion and translation is completed. -u Guarantee that any output is unbuffered. In the first synopsis form, the characters in string1 are translated into the characters in string2 where the first character in string1 is translated into the first character in string2 and so on. If string1 is longer than string2, the last character found in string2 is dupli- cated until string1 is exhausted. In the second synopsis form, the characters in string1 are deleted from the input. In the third synopsis form, the characters in string1 are compressed as described for the -s option. In the fourth synopsis form, the characters in string1 are deleted from the input, and the characters in string2 are compressed as described for the -s option. The following conventions can be used in string1 and string2 to specify sets of characters: character Any character not described by one of the following conven- tions represents itself. \octal A backslash followed by 1, 2 or 3 octal digits represents a character with that encoded value. To follow an octal se- quence with a digit as a character, left zero-pad the octal sequence to the full 3 octal digits. \character A backslash followed by certain special characters maps to special values. \a <alert character> \b <backspace> \f <form-feed> \n <newline> \r <carriage return> \t <tab> \v <vertical tab> A backslash followed by any other character maps to that character. c-c For non-octal range endpoints represents the range of char- acters between the range endpoints, inclusive, in ascending order, as defined by the collation sequence. If either or both of the range endpoints are octal sequences, it repre- sents the range of specific coded values between the range endpoints, inclusive. See the "COMPATIBILITY" section below for an important note regarding differences in the way the current implementation interprets range expressions differently from previous im- plementations. [:class:] Represents all characters belonging to the defined character class. Class names are: alnum <alphanumeric characters> alpha <alphabetic characters> blank <whitespace characters> cntrl <control characters> digit <numeric characters> graph <graphic characters> ideogram <ideographic characters> lower <lower-case alphabetic characters> phonogram <phonographic characters> print <printable characters> punct <punctuation characters> rune <valid characters> space <space characters> special <special characters> upper <upper-case characters> xdigit <hexadecimal characters> When "[:lower:]" appears in string1 and "[:upper:]" appears in the same relative position in string2, it represents the characters pairs from the toupper mapping in the LC_CTYPE category of the current locale. When "[:upper:]" appears in string1 and "[:lower:]" appears in the same relative posi- tion in string2, it represents the characters pairs from the tolower mapping in the LC_CTYPE category of the current lo- cale. With the exception of case conversion, characters in the classes are in unspecified order. For specific information as to which ASCII characters are included in these classes, see ctype(3) and related manual pages. [=equiv=] Represents all characters belonging to the same equivalence class as equiv, ordered by their encoded values. [#*n] Represents n repeated occurrences of the character repre- sented by #. This expression is only valid when it occurs in string2. If n is omitted or is zero, it is be inter- preted as large enough to extend string2 sequence to the length of string1. If n has a leading zero, it is inter- preted as an octal value, otherwise, it is interpreted as a decimal value. ENVIRONMENT The LANG, LC_ALL, LC_CTYPE and LC_COLLATE environment variables affect the execution of tr as described in environ(7). EXIT STATUS The tr utility exits 0 on success, and >0 if an error occurs. EXAMPLES The following examples are shown as given to the shell: Create a list of the words in file1, one per line, where a word is taken to be a maximal string of letters. tr -cs "[:alpha:]" "\n" < file1 Translate the contents of file1 to upper-case. tr "[:lower:]" "[:upper:]" < file1 (This should be preferred over the traditional Unix idiom of "tr a-z A- Z", since it works correctly in all locales.) Strip out non-printable characters from file1. tr -cd "[:print:]" < file1 Remove diacritical marks from all accented variants of the letter `e': tr "[=e=]" "e" COMPATIBILITY Previous FreeBSD implementations of tr did not order characters in range expressions according to the current locale's collation order, making it possible to convert unaccented Latin characters (esp. as found in English text) from upper to lower case using the traditional Unix idiom of "tr A-Z a-z". Since tr now obeys the locale's collation order, this idiom may not produce correct results when there is not a 1:1 mapping between lower and upper case, or when the order of charac- ters within the two cases differs. As noted in the "EXAMPLES" section above, the character class expressions "[:lower:]" and "[:upper:]" should be used instead of explicit character ranges like "a-z" and "A-Z". "[=equiv=]" expression and collation for ranges are implemented for single byte locales only. System V has historically implemented character ranges using the syntax "[c-c]" instead of the "c-c" used by historic BSD implementations and standardized by POSIX. System V shell scripts should work under this implementation as long as the range is intended to map in another range, i.e., the command "tr [a-z] [A-Z]" will work as it will map the `[' character in string1 to the `[' character in string2. However, if the shell script is deleting or squeezing characters as in the command "tr -d [a-z]", the characters `[' and `]' will be included in the dele- tion or compression list which would not have happened under a historic System V implementation. Additionally, any scripts that depended on the sequence "a-z" to represent the three characters `a', `-' and `z' will have to be rewritten as "a\-z". The tr utility has historically not permitted the manipulation of NUL bytes in its input and, additionally, stripped NUL's from its input stream. This implementation has removed this behavior as a bug. The tr utility has historically been extremely forgiving of syntax er- rors, for example, the -c and -s options were ignored unless two strings were specified. This implementation will not permit illegal syntax. STANDARDS The tr utility conforms to IEEE Std 1003.1-2001 ("POSIX.1"). The "ideogram", "phonogram", "rune", and "special" character classes are extensions. It should be noted that the feature wherein the last character of string2 is duplicated if string2 has less characters than string1 is permitted by POSIX but is not required. Shell scripts attempting to be portable to other POSIX systems should use the "[#*]" convention in- stead of relying on this behavior. The -u option is an extension to the IEEE Std 1003.1-2001 ("POSIX.1") standard. FreeBSD 14.3 October 13, 2006 TR(1)
NAME | SYNOPSIS | DESCRIPTION | ENVIRONMENT | EXIT STATUS | EXAMPLES | COMPATIBILITY | STANDARDS
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=tr&manpath=FreeBSD+14.3-RELEASE+and+Ports>