FreeBSD Manual Pages
VLAN(4) Kernel Interfaces Manual VLAN(4) NAME vlan -- IEEE 802.1Q VLAN network interface SYNOPSIS To compile this driver into the kernel, place the following line in your kernel configuration file: device vlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_vlan_load="YES" DESCRIPTION The vlan driver demultiplexes frames tagged according to the IEEE 802.1Q standard into logical vlan network interfaces, which allows routing/bridging between multiple VLANs through a single switch trunk port. Each vlan interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). To function, a vlan interface must be assigned a parent interface and numeric VLAN tag using ifconfig(8). A single parent can be assigned to multiple vlan interfaces provided they have different tags. The parent interface is likely to be an Ethernet card connected to a properly con- figured switch port. The VLAN tag should match one of those set up in the switched network. vlan initially assumes the same minimum length for tagged and untagged frames. This mode is selected by setting the sysctl(8) variable net.link.vlan.soft_pad to 0 (default). However, there are network de- vices that fail to adjust frame length when it falls below the allowed minimum due to untagging. Such devices should be able to interoperate with vlan after changing the value of net.link.vlan.soft_pad to 1. In the latter mode, vlan will pad short frames before tagging them so that their length is not less than the minimum value after untagging by the non-compliant devices. HARDWARE The vlan driver supports efficient operation over parent interfaces that can provide help in processing VLANs. Such interfaces are auto- matically recognized by their capabilities. Depending on the level of sophistication found in a physical interface, it may do full VLAN pro- cessing or just be able to receive and transmit long frames (up to 1522 bytes including an Ethernet header and FCS). The capabilities may be user-controlled by the respective parameters to ifconfig(8), vlanhwtag, and vlanmtu. However, a physical interface is not obliged to react to them: It may have either capability enabled permanently without a way to turn it off. The whole issue is very specific to a particular de- vice and its driver. At present, these devices are capable of full VLAN processing in hard- ware: ae(4), age(4), alc(4), ale(4), bce(4), bge(4), bxe(4), cxgb(4), cxgbe(4), em(4), igb(4), ix(4), jme(4), liquidio(4), msk(4), mxge(4), nge(4), re(4), sge(4), stge(4), ti(4), and vge(4). Other Ethernet interfaces can run VLANs using software emulation in the vlan driver. However, some lack the capability of transmitting and re- ceiving long frames. Assigning such an interface as the parent to vlan will result in a reduced MTU on the corresponding vlan interfaces. In the modern Internet, this is likely to cause tcp(4) connectivity prob- lems due to massive, inadequate icmp(4) filtering that breaks the Path MTU Discovery mechanism. These interfaces natively support long frames for vlan: axe(4), bfe(4), cas(4), dc(4), et(4), fwe(4), fxp(4), gem(4), le(4), nfe(4), rl(4), sis(4), sk(4), ste(4), vr(4), vte(4), and xl(4). The vlan driver automatically recognizes devices that natively support long frames for vlan use and calculates the appropriate frame MTU based on the capabilities of the parent interface. Some other interfaces not listed above may handle long frames, but they do not advertise this ability. The MTU setting on vlan can be corrected manually if used in conjunction with such a parent interface. SEE ALSO ifconfig(8), sysctl(8) FreeBSD 13.2 December 26, 2020 VLAN(4)
NAME | SYNOPSIS | DESCRIPTION | HARDWARE | SEE ALSO
Want to link to this manual page? Use this URL:
<https://man.freebsd.org/cgi/man.cgi?query=vlan&manpath=FreeBSD+14.2-RELEASE+and+Ports>